录井系统雷击危害分析及模拟试验研究

针对雷击电磁辐射对录井系统的危害问题,建立了录井系统线路雷击危害模拟试验模型,采用8/20 μs冲击电流发生器,开展了录井系统的雷击耦合试验,定量分析了雷击电磁辐射对录井系统的影响。研究结果表明:随着电流的增大和距离电流通道的减小,耦合的电压随之增大;线缆长度越长耦合的电压越大,最大耦合电压达到了2 720 V;屏蔽层接地可以有效地减小电磁辐射对线缆的耦合作用。     

重大基坑坍塌事故虚拟仿真系统研究

为预防基坑坍塌事故发生、进行重大事故警示教育,以杭州地铁湘湖站北2基坑坍塌事故为素材,研究构建重大基坑坍塌事故虚拟仿真培训系统。对案例事故涉及的设计、施工、环境三大因素的技术问题进行总结,研究了事故链各致险因素及对推动事故发生所起作用,完成仿真系统平台设计和开发工作。系统应用多种制作技术创建工程场景模型,展示深基坑工程复杂的施工工序和空间关系,再现基坑坍塌事故发生发展过程和贴近实际的灾难场景。研究结果表明:仿真系统成果可丰富地下工程教学、施工现场安全教育和安全监察培训的内容和形式。     

石化装置安全仪表系统KooN表决结构的误跳车率定量分析

为了更准确量化安全仪表系统的误跳车率,基于联锁回路SIF中传感器、逻辑解算器、执行机构引发误跳车的不同失效机理和模型,考虑共因失效对误跳车率的影响,提出1种更符合实际并适用于异型KooN结构的新子系统误跳车率计算模型（STR of Non-identical Redundant System,SNRS）。针对SIF回路的误跳车率计算,建立了1种分析安全联锁SIF回路误跳车率（Reliability based Spurious Trip,RST）的计算框架。研究结果表明:以某聚丙烯装置第三反应器保护系统为例,将SNRS和RST方法与目前主流的多种计算方法进行数值计算对比,验证了方法的有效性,能够有效进行定量分析。     

基于火探管式的锂离子电池灭火技术研究

为研究锂离子电池灭火方案,基于火探管灭火技术同时利用新型清洁灭火剂Novec 1230,组装成火探管灭火系统。在灭火测试平台上以功率为200 W的电热管作为外热源引发单电池或电池模组热失控,通过改变火探管的布置位置,记录相应的灭火行为以及灭火效率,并对实验结果进行了分析。研究结果表明,当火探管灭火系统直接布置在电池正上方时,在起火后的5.6s内控制火情;随着灭火剂用量增加可以显著降低体系温度,防止电池复燃以及连锁热失控现象发生;火探管有效覆盖区域外的失控电池作为热源将继续加热临近电池,引发连锁热失控,造成灭火系统失效;根据电池热失控后的燃烧行为以及传热行为,提出相应的火探管灭火系统复合方案。     

A comparative study of vocational education and occupational safety and health training in China and the UK

In order to enhance Chinese workers’ occupational safety awareness, it is essential to learn from developed countries’ experiences. This article investigates thoroughly occupational safety and health (OSH) in China and the UK; moreover, the article performs a comparison of Chinese and British OSH training-related laws, regulations and education system. The following conclusions are drawn: China’s work safety continues to improve, but there is still a large gap compared with the UK. In China a relatively complete vocational education and training (VET) system has been established. However, there exist some defects in OSH. In the UK, the employer will not only pay attention to employees’ physiological health, but also to their mental health. The UK’s VET is characterized by classification and grading management, which helps integrate OSH into the whole education system. China can learn from the UK in the development of policies, VET and OSH training.     

Usability of non-standard lower anchor configurations for child restraint system (CRS) installation

Abstract

Objectives: The objective of this study was to determine whether the amount of tension required for proper child restraint system (CRS) installation varies with lower anchor spacing and to determine whether nonexperts can produce adequate tension on wider-than-standard lower anchor configurations.

Methods: CRSs were installed by certified child passenger safety technicians (CPSTs; n?=?6 subjects, n?=?72 installations) and nonexperts (n?=?30 subjects, n?=?120 installations) on a mock-up vehicle seat fixture with lower anchors set at 11 (standard), 15, 19, and 23 in. apart from one another. Each CPST installed a rear-facing (RF) infant base, RF convertible, and forward-facing (FF) convertible into each of the 4 spacing configurations in random order. The CPSTs were instructed to tighten the lower connector strap until the tension was exactly at the threshold between passing and failing the 1-in. test. Each nonexpert installed one CRS model into all 4 spacing conditions in random order. Nonexperts were instructed to install the CRS to the best of their ability. The tension produced on the lower connector strap was recorded via load cell in the lower anchor assembly of the vehicle seat. Resultant tension magnitudes were compared across spacing conditions using matched pair t-tests. The CPSTs’ mean 1-in. test threshold values were compared to tensions produced by nonexperts. Installations were visually evaluated for errors and qualitative usability feedback was collected via survey.

Results: CPSTs installed the infant base with higher tensions in the 15-, 19-, and 23-in. configurations compared to the standard 11-in. configuration (P = .034, .032, and .003, respectively). The nonexperts installed the infant base with higher tension in the 15- and 23-in. configurations compared to the 11-in. configuration (P = .004 and .026, respectively). The RF convertible and FF convertible installations showed no significant differences in tension among any of the spacing configurations for either group. Only 19% of the nonexperts’ installations were tight enough to pass CPST thresholds, and the pass rate did not vary with respect to lower anchor spacing. In feedback surveys, the nonexpert group did not show a consistent preference for either standard or wider-than-standard lower anchor configurations.

Conclusions: The amount of tension required to pass the 1-in. rule did not vary with lower anchor spacing configurations for the RF and FF convertible CRS, but the infant base required more tension in wider anchor configurations. Nonexperts tended to produce less than ideal tension in all configurations, although their tension magnitudes increased for the infant base in wider configurations.     

H∞ loop-shaping controller design for a grid-connected single-phase photovoltaic system

This paper presents a H_∞ loop-shaping controller for controlling dc-link voltage by regulating the switching signal of the inverter associated with a grid-connected single-phase photovoltaic system. To facilitate a robust control design, state-space realisation of the system model is made with uncertainties represented by linear fractional transformation. The controller is achieved through H_∞ synthesis followed by obtaining desired loop shapes through the choice of the proper weighting functions. The controller order is reduced by Henkel-norm method for facilitating its practical implementation. Controller performance is evaluated through carrying out simulations on MATLAB/Simulink platform under standard and changing atmospheric conditions, and fault condition.     

Development of a fuel cell propulsion system for the existing Mercedes B-Class 160 of petrol driven car

This paper presents a theoretical comparison between fuel cell (FC) power train and conventional petrol driven propulsion system. FC has potential to reduce the CO₂-emissions from road. However, FC power trains require energy storing device, to meet the peak power during extreme drive situations and also able to recover the kinetic energy of the vehicle during break operation. The proposed system includes a polymer electrolyte membrane fuel cell (PEMFC) based drive train and a super capacitor connected in parallel. The system is designed and dimensioned for a conventional petrol driven propulsion system of the Mercedes B-Class160. The feasibility study also includes comparison between the existing conventional systems. It is shown that although FC power train is heavier compared to existing system, urban performance is better and produces no CO₂ and other harmful emissions.     

公众生态文明素养及其科普教育研究

本文对国家文明城市芜湖市进行实地问卷调查发现:公众具有一定生态意识,但生态文明素养整体状况不佳。公众对生态文明概念比较了解和很了解的只占17.7%;各类人群对周围环境关注度较高,均在65%左右;有相关生态知识或行为的公众占92%;有76.7%的人表示没有破坏环境的行为;64.8%的受访者表示他们有保护环境的行为。通过生态科普教育现状调查发现:受访者对目前生态科普教育满意度只有25.9%,政府在生态科普教育方面还存在活动流于形式、创新性不强、投入不足、制度不完善、不能及时回应公众关切热点、专项科普匮乏、媒体不给力、内容不接地气、无区域特色、平台手段落后等问题。提出了提升公众生态文明素养需构建四个相互联动的科普教育体系:高度重视生态科普教育的思想体系、支撑生态科普教育的技术能力体系、生态科普教育的长效机制体系和具有区域特色生态科普教育内容体系。     

生态文明制度体系研究——以江苏省为例

生态文明制度体系是由制度构成的一个相互配合、有机联系的整体。本文基于文献统计分析与实地调研咨询,从广义和狭义层面,分别对生态文明制度进行梳理。根据国家生态文明建设需求与省级层面实际情况,本文将广义的生态文明制度体系分为源头保护制度体系、损害赔偿与激励体系、追责考评制度体系和污染治理制度体系四大板块,并针对国家与省级重点生态文明制度,构建生态资源保护制度链与污染防治制度链。同时,对制度地位、制度衔接、相互关系及其优化选择进行分析,以提高环境管理效能,推进生态文明研究纵深发展。