热能（火用）平衡在芳烃分离装置清洁生产审核中的实践

运用热能（火用）平衡理论于芳烃分离装置清洁生产审核中,建立了芳烃分离装置热能（火用）平衡。热能（火用）平衡测算结果表明：此芳烃分离装置的热能利用效率（实际）为61．65％、热（火用）利用效率（实际）为59．77％、热力学第一定律效率和热力学第二定律效率分别为23．93％和7．76％。依据清洁生产审核思路,对此芳烃分离装置的热能（火用）利用效率进行了原因分析并提出了预防对策,可为提出清洁生产方案提供定量化依据。     

Modeling the current-voltage characteristics of thin-film silicon solar cells based on photo-induced electron transfer processes

Power conversion efficiency of p-i-n type microcrystalline silicon (c-Si:H) solar cells has been analyzed in terms of sequential processes of photo-induced electron transfer. The effect of the excitonic state on the charged carrier generation has been studied compared to a conventional scheme in which only charged carriers are taken into account for the operation of the solar cells. A numerical model has been developed to calculate current-voltage characteristics of solar cells on the basis of two types of charged carrier generation processes (exciton process and charged carrier process). The light trapping effect due to a textured back surface reflector (BSR) was embedded in the numerical model by using the effective medium theory in combination with the matrix method in the field of the electromagnetic theory of light. As an application of this modeling, it was found that the reported data of the power conversion efficiency were not explained by the conventional charged carrier process model and that the combined model of the charged carrier process with the exciton process well explains the performance of the p-i-n type c-Si:H solar cells. In this way, the typical power conversion efficiencies were estimated to be 10.5% for the device (i-layer thickness: 1.8 m) with the BSR (period: 600 nm; height: 250 nm) and 8.6% for the device with the flat reflector under the condition that the fractions of the exciton process and charged carrier process were 60% and 40%, respectively.     

Modeling the current-voltage characteristics of thin-film silicon solar cells based on photo-induced electron transfer processes

Power conversion efficiency of p-i-n type macrocrystalline silicon (µc-Si:H) solar cells has been analyzed in terms of sequential processes of photo-induced electron transfer. The effect of the excitonic state on the charged carrier generation has been studied compared to a conventional scheme in which only charged carriers are taken into account for the operation of the solar cells. A numerical model has been developed to calculate current-voltage characteristics of solar cells on the basis of two types of charged carrier generation processes (exciton process and charged carrier process). The light trapping effect due to a textured back surface reflector (BSR) was embedded in the numerical model by using the effective medium theory in combination with the matrix method in the field of the electromagnetic theory of light. As an application of this modeling, it was found that the reported data of the power conversion efficiency were not explained by the conventional charged carrier process model and that the combined model of the charged carrier process with the exciton process well explains the performance of the p-i-n type μc-Si:H solar cells. In this way, the typical power conversion efficiencies were estimated to be 10.5% for the device (i-layer thickness: 1.8 μm) with the BSR (period: 600 nm; height: 250 nm) and 8.6% for the device with the flat reflector under the condition that the fractions of the exciton process and charged carrier process were 60% and 40%, respectively.     

温度对干化污泥水蒸气气化产气特性的影响

采用固定床气化装置,在水蒸气流量为0.32 kg/h条件下进行了污泥水蒸气气化实验。研究了温度对污泥气化气体产率、氢气产率、气体成分与低位热值、气体能源转化率的影响。结果表明:随着反应温度从700℃上升到1 000℃;气体产率从0.39 m3/kg升至0.61 m3/kg;氢气产率从0.18 m3/kg升至0.34 m3/kg;气体能源转化率从54%升至88%;产气的低位热值从10 688.1 kJ/m3提高至11 168.9 kJ/m3。同时产气中H2和CO含量随着温度的升高而增加,CH4、CO2和CnHm含量随温度的升高而减少。因此,为了获得更多的可燃气体,建议在污泥水蒸气气化工艺中,气化温度必须大于800℃。     

一株好氧反硝化菌的筛选鉴定及固定化研究

从污水处理厂的活性污泥中筛选得到1株好氧反硝化细菌(YS),对其进行分子生物学鉴定和理化性能测试,并考察了该菌株固定化前后反硝化能力的变化.鉴定结果表明,菌株YS为反硝化产碱菌(Alcaligenes denitrificans).菌株经固定化后,其酶活力有所下降,但稳定性增强,在4 ℃下储存50 d后,固定态菌株对硝酸根的去除率仍可维持在80%以上,而游离态菌株仅为15%.在pH 7.0条件下,固定态菌株的反硝化率比游离态菌株低3%左右,但当pH降低至5.0时,固定态菌株对硝酸根的去除率为72.4%,比游离态菌株高2.6%,表明固定态菌株比游离态菌株更适应于弱酸的环境.在不同的工艺条件下,固定态菌株与游离态菌株反硝化能力的变化趋势相同.菌株YS的最适条件为:接种量1.5%左右,pH为6.0,C/N比为11,葡萄糖为碳源.     

新型生物滴滤填料性能评价

填料是微生物附着生长、水分保持的支撑体,填料的性能直接关系到污染物的最终去除效果.研究开发了3种新型生物滴滤填料:纹翼多面球、改性毛刺球和空心多面柱.测试表明3种填料中,空心多面柱和纹翼多面球的结构特性参数均优于普通的生物滴滤填料,特别是比表面积,达到了200 m2·m-3左右.纹翼多面球的阻力系数ζ在挂膜前后几乎没有变化,而毛刺球的阻力系数ζ增长明显.生物滴滤塔(BTF)实验表明,采用空心多面柱的BTF挂膜启动的时间明显快于其他两种填料;稳定运行阶段实验结果表明,当甲苯和乙醇进口浓度分别为687.37 mg·m-3和651.17 mg·m-3时,采用纹翼多面球的BTF去除效果较好,对于两者的去除率分别达到了76.78%和99.23%.生物量测试表明,3种填料湿生物量也均高于普通的聚丙烯鲍尔环.纹翼多面球填料易实现生物膜的更新与剥落,稳定运行后期单位填料层压降维持在51.6 Pa·m-1,而毛刺球平均压降显著升高(193.3 Pa·m-1),出现了严重堵塞现象.     

退役三元锂电池循环利用系统减碳效率评估及优化分析

随着我国新能源汽车产业的快速发展,大批动力电池进入退役期.针对退役动力电池循环利用现状,识别降本减碳协同效应并开展系统优化分析,成为重要研究课题.本文综合采用生命周期评价和生命周期成本方法,分析了当前我国退役三元锂电池循环利用系统的碳足迹和经济成本.结果表明,1GWh容量的退役三元锂电池循环利用系统碳足迹和生命周期成本分别为-2.33×10⁷kgCO₂eq和-33613.15万元.结合碳足迹和生命周期成本二维指标开展减碳效率评估和情景分析发现,相对于现实系统,汽车生产商主导的优化情景减碳效率较低,提高梯次利用比例的优化情景具有最优减碳效率.通过提高梯次利用比例和采用先进资源化技术均能够显著提升退役三元锂电池循环利用系统的减碳效率.     

季节性干旱下喀斯特次生林不同树种水分利用效率变化

植物叶片水分利用效率(WUE)对环境变化的响应特征和机制是理解生态系统碳循环和水循环及其耦合关系的基础。为探讨季节性干旱下喀斯特次生林中不同植物的WUE变化,以普定次生林通量观测站内的喀斯特次生林为例,在连续干旱背景下分别对8种常见植物的叶片WUE进行了测定分析。结果表明:(1)研究区常见植物的叶片WUE日间主要在0.65～7.73μmol/mmol之间变化。8种植物的叶片WUE均以上午9点最大,厚果崖豆藤(Millettia pachycarpa)、朴树(Celtis sinensis)和马桑(Coriaria nepalensis)的WUE均在下午3点就降到最低,而铁线莲(Clematis florida)、木通(Akebia quinata)、石岩枫(Mallotus repandus)、梓树(Catalpa ovata)和构树(Broussonetia papyrifera)的WUE则在下午5点才降到最低。厚果崖豆藤、铁线莲、石岩枫、朴树、构树的WUE日间变化均较显著。(2)研究区植物叶片的WUE以藤本植物最高。上午9点、11点和下午3点,植物叶片WUE的种间差异均不显著,而在下午1点、5点,植物叶片WUE在种间均存在显著差异。(3)石岩枫和木通的叶片WUE与环境光照强度均呈显著正相关关系。朴树和铁线莲的叶片WUE与环境相对湿度均呈极显著正相关关系。厚果崖豆藤的叶片WUE与环境空气温度间也呈现出极显著的正相关关系。朴树、构树、马桑、石岩枫、铁线莲、厚果崖豆藤的叶片WUE与净光合速率均显著正相关,木通的叶片WUE与蒸腾速率显著负相关。研究区8种植物叶片WUE与叶面水汽压亏缺间的相关性均不显著。(4)植物种和外部环境对研究区植物叶片的WUE均有显著影响,木通、厚果崖豆藤、铁线莲在遭遇连续干旱后叶片WUE均较高,对生境恶劣的喀斯特环境具有较强的适应能力。     

烟气温度对电除尘器性能影响的数值模拟

采用计算流体动力学（CFD）软件对电除尘器进行三维数值模拟研究,通过自定义函数（UDF）实现电场、流场、颗粒场和温度场的4场耦合,研究烟气温度对电除尘器电场特性、流场特性和除尘效率的影响.结果显示：入口烟气质量流量相同时,当烟气温度从20℃上升到400℃时,平均电场强度从4.9×10⁵V/m减小到1.4×10⁵V/m,平均板电流密度从0.971mA/m²降至0.261mA/m²,但板电流密度分布的均匀性逐渐变好;烟气温度上升平均湍流强减小,离子风效应也随之减小.当入口烟气体积流量相同时,随着烟气温度的增加,颗粒运动轨迹线拉长,整体的颗粒捕集效率减低.降低烟气温度可以有效提高电除尘器的除尘效率.     

针对工作流量为2 L·min-1的切割器的捕集效率评价研究

为了评价市面上不同工作流量的切割器,本研究搭建了一套基于静态箱法的切割器捕集效率评价系统,可调节切割器的采样流量,结合空气动力学粒径谱仪对不同工作流量的切割器进行捕集效率测量.通过使用8种粒径的单分散聚苯乙烯微球,对多个品牌的工作流量为2、3及16.67 L·min^-1的PM₁、PM_2.5及PM₁₀切割器进行了评价,得到其捕集效率为50%时的空气动力学粒径分别为1.12、2.52和10.39 μm（品牌一）;2.69和10.41 μm（品牌二）;2.56、10.43 μm（型号Dust trak）;1.04、2.51 μm（型号VSCC）.本研究对于评价不同流量、不同原理的切割器的性能、提高颗粒物监测结果的准确性具有一定的科学意义.