厌氧氨氧化工艺脱氮及其污泥形态的研究

为研究厌氧氨氧化工艺对高浓度含氮废水的脱氮性能,在以聚乙烯海绵作为填料的上流式厌氧固定床反应器中利用人工配置高浓度含氮废水进行了实验研究.实验中通过添加充足无机碳源,实现了厌氧氨氧化反应器在总氮浓度900～1 210 mg/L长期稳定的运行,脱氮效率在80％以上,最高氮负荷为5.9 kg/m3·d.结果表明:充足的无机碳源在一定程度上可有效地降低高浓度亚硝氮对厌氧氨氧化菌的抑制作用.通过对污泥性状的研究,明确寻找出污泥上浮的原因所在.通过Stover-Kincannon模型确定系统动力学参数KB和Umax分别为30.2 g/L·d和2L2g/L·d,这将有助于对该厌氧氨氧化系统各控制条件的有效调节和准确设定,也为日后应用于实际工程中提供重要的理论依据.     

微波消解/ICP-AES法分析冶炼厂固废中重金属

分析固体废物中金属元素全量分析的微波消解条件,通过实验确定样品的粉碎粒度、消解功率、消解温度、消解时间等因素对样品消解效果的影响,以等离子发射光谱测定冶炼厂固体废物中24种痕量金属元素,通过测定的检出限、精密度、准确度,确立冶炼厂固体废物痕量金属全量分析检测方法准确高效。     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

非均相类Fenton试剂的制备及其在焦化废水处理中的应用研究

利用浸渍法,将Fe3＋负载在经酸碱改性后的粉状活性炭上,当浸渍液浓度为2．5％,固化温度为270℃时,制成的催化剂催化活性较高。用自制的非均相类benton试剂降解焦化废水,通过正交试验和极差分析得出,影响因素的主次顺序为催化剂用量〉初始pH值〉反应时间〉H：0：投加量。结果表明,在100ml水样中。室温条件下,初始pH值为4．0,催化剂使用量为1．5g,H20：投加量为5ml（分两次投加）,反应时间为90min时,COD去除率可达99％。采用混凝＋化学沉淀＋非均相类Fenton试剂法处理焦化废水,各主要出水水质指标为：色度lO倍;COD浓度38．5mg／L;氨氮浓度8．4mg／L,达到国家一级排放标准。     

土地利用变化对土壤硝化及氨氧化细菌区系的影响

以西藏高原相邻的原始森林、天然草原和农田土壤为研究对象,分别采用室内培养法和nested PCR-DGGE技术,对比研究了这3个生态系统的土壤硝化势、硝态氮浓度以及土壤氨氧化细菌（AOB）菌群区系.结果表明,农田土壤的硝化势和硝态氮（NO 3--N）浓度显著高于相邻的草原和森林土壤,硝化势分别是森林和草原土壤的9倍和11倍,NO 3--N是农田土壤无机氮（Nmin）的主要成分,占无机氮的70%～90%.铵态氮（NH 4＋-N）则是森林和草原土壤中主要的无机氮形态.原始森林和天然草原间的硝化势和硝态氮浓度没有显著差异.原始森林的土壤AOB菌群数量、多样性及均匀度最低.天然草原生态系统转换为农田后,土壤AOB菌群的多样性和均匀度显著降低,但是农田土壤的AOB菌群结构仍与其前身草原生态系统有较高的相似性.原始森林的AOB菌群数量、多样性及均匀度最低直接导致了其硝化势最低;农田土壤的硝化势和硝态氮浓度最高意味着农田生态系统中优势AOB的活性最高.以上结果表明,土地利用变化导致土壤氮素内循环及其关键微生物AOB的多样性与活性均发生显著变化,这些变化会影响土壤环境质量以及生态系统的持续与稳定.