Buses retrofitting with diesel particle filters: Real-world fuel economy and roadworthiness test considerations

Retrofitting older vehicles with diesel particulate filter(DPF) is a cost-effective measure to quickly and efficiently reduce particulate matter emissions. This study experimentally analyzes real-world performance of buses retrofitted with CRT DPFs. 18 in-use Euro III technology urban and intercity buses were investigated for a period of 12 months. The influence of the DPF and of the vehicle natural aging on buses fuel economy are analyzed and discussed. While the effect of natural deterioration is about 1.2%–1.3%, DPF contribution to fuel economy penalty is found to be 0.6% to 1.8%, depending on the bus type. DPF filtration efficiency is analyzed throughout the study and found to be in average 96% in the size range of 23–560 nm. Four different load and non-load engine operating modes are investigated on their appropriateness for roadworthiness tests. High idle is found to be the most suitable regime for PN diagnostics considering particle number filtration efficiency.     

Characteristics of the pollutant emissions in a tunnel of Shanghai on a weekday

Tunnel displays a typical semi-closed environment, and multitudes of the pollutants tend to accumulate. The samples of gaseous pollutants and particulate matter(PM) were collected from the Xiangyin tunnel at Shanghai to investigate the characteristics of the pollutant emissions. The results indicated that both gaseous pollutants and PM exhibited much higher concentrations during the rush hours in the morning and at night due to vehicle emission. Two peaks of the PM concentration were observed in the scope of 0.7‐1.1 and 3.3–4.7 μm, accounting for 14.6% and 20.3% of the total concentrations, respectively.Organic matter(OM), EC, and many water-soluble ions were markedly higher at the rush hours in the morning than those at night, implicating comprehensive effects of vehicle types and traffic volume. The particle number concentrations exhibited two peaks at Aitken mode(25 nm and 100 nm) and accumulation mode(600 nm), while the particle volume concentration displayed high values at the accumulation mode(100–500 nm) and coarse mode(2.5–4.0 μm). The peak around 100 nm was detected in the morning rush hours, but it diminished with the decrease of the traffic volume. Individual-particle analysis revealed that main particles in the tunnel were Fe-rich particles, K-rich particles, mineral particles,Ca–S rich particles and Al–Si particles. The particles collected at the rush hours displayed marked different morphologies, element concentrations and particle sizes compared to the ones collected at the non-rush period. The data presented herein could shed a light on the feature of vehicle emissions.     

Estimation and validation of PM2.5/PM10 exhaust and non-exhaust emission factors for practical street pollution modelling

In order to carry out efficient traffic and air quality management, validated models and PM emission estimates are needed. This paper compares current available emission factor estimates for PM₁₀ and PM_2.5 from emission databases and different emission models, and validates these against eight high quality street pollution measurements in Denmark, Sweden, Germany, Finland and Austria.The data sets show large variation of the PM concentration and emission factors with season and with location. Consistently at all roads the PM₁₀ and PM_2.5 emission factors are lower in the summer month than the rest of the year. For example, PM₁₀ emission factors are in average 5–45% lower during the month 6–10 compared to the annual average.The range of observed total emission factors (including non-exhaust emissions) for the different sites during summer conditions are 80–130 mg km⁻¹ for PM₁₀, 30–60 mg km⁻¹ for PM_2.5 and 20–50 mg km⁻¹ for the exhaust emissions.We present two different strategies regarding modelling of PM emissions: (1) For Nordic conditions with strong seasonal variations due to studded tyres and the use of sand/salt as anti-skid treatment a time varying emission model is needed. An empirical model accounting for these Nordic conditions was previously developed in Sweden. (2) For other roads with a less pronounced seasonal variation (e.g. in Denmark, Germany, Austria) methods using a constant emission factor maybe appropriate. Two models are presented here.Further, we apply the different emission models to data sets outside the original countries. For example, we apply the “Swedish” model for two streets without studded tyre usage and the “German” model for Nordic data sets. The “Swedish” empirical model performs best for streets with studded tyre use, but was not able to improve the correlation versus measurements in comparison to using constant emission factors for the Danish side. The “German” method performed well for the streets without clear seasonal variation and reproduces the summer conditions for streets with pronounced seasonal variation. However, the seasonal variation of PM emission factors can be important even for countries not using studded tyres, e.g. in areas with cold weather and snow events using sand and de-icing materials. Here a constant emission factor probably will under-estimate the 90-percentiles and therefore a time varying emission model need to be used or developed for such areas.All emission factor models consistently indicate that a large part (about 50–85% depending on the location) of the total PM₁₀ emissions originates from non-exhaust emissions. This implies that reduction measures for the exhaust part of the vehicle emissions will only have a limited effect on ambient PM₁₀ levels.     

气浮-水解酸化-高效接触氧化工艺处理汽车废水

对某汽车公司的废水处理系统进行了改造,采用气浮-水解酸化-高效接触氧化工艺对其废水进行了处理,在水解酸化池中使用生物微电解填料,在接触氧化池内使用LK40弹性立体网状生物亲和性组合填料.经该体系处理后,出水水质为pH=6～9、SS＜60mg/L、CODCr＜90mg/L、BOD5＜20mg/L、石油类＜5mg/L,达到DB44/26-2001中一级标准,其处理费用为1.91元/m3.     

特种作业人员存在的问题及解决办法初探

例举了武钢金山店铁矿特种作业人员中存在的问题,提出了相应的解决办法。     

On-board measurement of emissions from liquefied petroleum gas, gasoline and diesel powered passenger cars in Algeria

On-board measurements of unit emissions of CO,HC,NOx and CO2 were conducted on 17 private cars powered by different types of fuels including gasoline,dual gasoline–liquefied petroleum gas(LPG),gasoline,and diesel. The tests performed revealed the effect of LPG injection technology on unit emissions and made it possible to compare the measured emissions to the European Artemis emission model. A sequential multipoint injection LPG kit with no catalyst installed was found to be the most efficient pollutant reduction device for all of the pollutants,with the exception of the NOx. Specific test results for a sub-group of LPG vehicles revealed that LPG-fueled engines with no catalyst cannot compete with catalyzed gasoline and diesel engines. Vehicle age does not appear to be a determining parameter with regard to vehicle pollutant emissions. A fuel switch to LPG offers many advantages as far as pollutant emissions are concerned,due to LPG's intrinsic characteristics.However,these advantages are being rapidly offset by the strong development of both gasoline and diesel engine technologies and catalyst converters. The LPG's performance on a chassis dynamometer under real driving conditions was better than expected. The enforcement of pollutant emission standards in developing countries is an important step towards introducing clean technology and reducing vehicle emissions.     

无人机遥感技术在环境保护领域中的应用进展

从建设项目环境保护管理、环境监测、环境应急、生态保护以及环境监察等方面阐述无人机遥感技术在环境保护领域中的应用现状,并对无人机影像的后期处理常用方法及最新发展动向进行了阐述。总结了目前无人机遥感技术在环境保护领域中存在的问题,对数据后处理技术研究方向作出展望。     

An estimation of vehicle kilometer traveled and on-road emissions using the traffic volume and travel speed on road links in Incheon City

The objective of this study is to estimate the vehicle kilometer traveled (VKT) and on-road emissions using the traffic volume in urban. We estimated two VKT; one is based on registered vehicles and the other is based on traffic volumes. VKT for registered vehicles was 2.11 times greater than that of the applied traffic volumes because each VKT estimation method is different. Therefore, we had to define the inner VKT is moved VKT inner in urban to compare two values. Also, we focused on freight modes because these are discharged much air pollutant emissions. From analysis results, we found middle and large trucks registered in other regions traveled to target city in order to carry freight, target city has included many industrial and logistics areas. Freight is transferred through the harbors, large logistics centers, or via locations before being moved to the final destination. During this process, most freight is moved by middle and large trucks, and trailers rather than small trucks for freight import and export. Therefore, these trucks from other areas are inflow more than registered vehicles. Most emissions from diesel trucks had been overestimated in comparison to VKT from applied traffic volumes in target city. From these findings, VKT is essential based on traffic volume and travel speed on road links in order to estimate accurately the emissions of diesel trucks in target city. Our findings support the estimation of the effect of on-road emissions on urban air quality in Korea.