二氧化钛光催化消毒技术在水处理中的研究

二氧化钛光催化消毒是一种新型的水处理技术,可以有效地去除水中常规的和新出现的致病微生物,杀菌效果好且相对常规消毒手段消毒副产物较少,处理工艺自身不会对处理水造成二次污染。通过总结光催化技术的研究历史,阐述了光催化氧化机理和杀灭微生物的具体过程,综述了二氧化钛光催化技术在水处理领域中杀灭细菌、真菌、藻类、原生动物和病毒的研究成果,论述了二氧化钛光催化消毒的必要性,并对二氧化钛光催化消毒的应用前景作了展望。     

Influencing factors and degradation products of antipyrine chlorination in water with free chlorine

Owing to its low cost, free chlorine is one of the most common disinfectants for wastewater and drinking water treatment. However, the formation of disinfection byproducts has been found to occur after free chlorine disinfection in recent decades. Antipyrine (ANT), an anti-inflammatory analgesic, has been frequently detected in the aquatic environment. In this work, the removal efficiency of ANT by free chlorine oxidation in ultrapure water was investigated with batch experiments. The influencing factors on the removal of ANT were explored at initial concentrations of ANT from 0.04 to 0.64 mg/L, free chlorine dosage from 0.30 to 1.31 mg/L, and pH from 1.5 to 9.0. The main degradation products were identified by solid phase extraction-gas chromatography-mass spectrometry. The results showed that ANT reacted rapidly with free chlorine in ultrapure water systems and up to 90.6% removal efficiency of ANT was achieved after 25 sec (initial free chlorine 1 mg/L, ANT 0.5 mg/L, pH 7.0). Higher oxidant dosage, lower ANT initial concentration and low pH favor the ANT removal. The main degradation product in ANT chlorination was a monochlorine substitution product (4-chloro-1,2-dihydro- 1,5-dimethyl-2-phenyl-3H-pyrazol-3-one), which can be further chlorinated by free chlorine. In addition, the total organic carbon result indicated that ANT is difficult to be mineralized using chlorine.     

城市生活污水处理中紫外线消毒工艺方案的设计与运用

城市生活污水处理中消毒工艺方案的确定是污水厂设计过程中需要考虑的重要问题,针对此问题从消毒方法的选用到出水消毒工艺的确定,设计出一套适合昆明市各污水处理厂的紫外线消毒技术方案。     

消毒副产物生成的温度影响和动力学模型

在水厂和供水管网中,加氯消毒副产物(DBPs)的生成浓度会随着季节转换和水温变化而出现明显波动.为了探究不同温度条件下DBP生成浓度的变化规律,本研究利用腐殖酸(HA)作为有机前体物进行加氯消毒,参照DBP统一生成条件(uniform formation condition,UFC),在不同水温下监测DBP[包括三卤甲烷(THM)和卤乙酸(HAA)]的生成浓度,并从动力学角度对该生成反应的机制做出分析,进而建立初步的浓度预测模型.结果表明,对于检测到的3种典型DBPs[三氯甲烷(CHCl3)、二氯乙酸(DCAA)和三氯乙酸(TCAA)],水温升高均能够明显提高其生成速率和最大生成浓度,其中后者随着温度的升高近似呈指数增长(R2>0.90).根据一级反应动力学模型对各组温度条件下的DBP实测值进行拟合,得到了较好的相关性(R2>0.94).为了进一步验证该动力学模型的准确性和可靠性,在20℃和30℃条件下分别采用该模型对DBP的实际生成浓度进行预测,并与实测值进行比较,均得到了良好的预测结果.为定量研究温度对DBP生成速率的影响规律,利用阿伦尼乌斯公式计算得到CHCl3、DCAA和TCAA的表观反应活化能分别为22.3、25.5和40.8 kJ.mol-1.     

KMnO4-PAC对高原喀斯特湖库DOM的DBPsFP控制

以云贵高原典型喀斯特湖库红枫湖取水口溶解性有机质（DOM）为研究对象,调查不同组合方式下高锰酸钾-聚合氯化铝（KMnO₄-PAC）对消毒副产物的生成潜能（DBPsFP）变化和平均组成分布,并通过红外光谱（FTIR）和三维荧光光谱（3D-EEM）对部分样品进行化学表征,推断其影响机制.结果表明：在0.1,0.2,0.4mg/L KMnO₄投加量下,DBPsFP降低17.5~73%,DOM的卤代活性化学结构和官能团部分被有效钝化;PAC的网捕和卷扫效应使DBPsFP进一步减少27.9~86.1%,组合工艺对DBPs的生成潜能影响大小为：三卤甲烷（THM₄） > 卤乙酸（HAA₉） > 卤乙腈（HAN₄）/卤代酮（HK₂）/三氯硝基甲烷（TCNM）.FTIR的结果表明预氧化后3300cm^-1处的透过率降低,指纹区1000~1300cm^-1处的峰频提升,表明分子中的O-H、COOH和C-O官能团增加,共轭不饱和结构在KMnO₄作用下部分消失.3D-EEM验证了外源有机物（腐殖酸）在DOM中占比随KMnO₄浓度梯度升高而下降,同时类蛋白结构的吸收峰强度增加,说明最终DBPs贡献可能源于DOM中剩余的小分子类蛋白（氨基酸）.     

Silica-quaternary ammonium “Fixed-Quat” nanofilm coated fiberglass mesh for water disinfection and harmful algal blooms control

Intensification of pollution loading worldwide has promoted an escalation of different types of disease-causing microorganisms, such as harmful algal blooms(HABs), instigating detrimental impacts on the quality of receiving surface waters. Formation of unwanted disinfection by-products(DBPs) resulting from conventional disinfection technologies reveals the need for the development of new sustainable alternatives. Quaternary Ammonium Compounds(QACs) are cationic surfactants widely known for their effective biocidal properties at the ppm level. In this study, a novel silica-based antimicrobial nanofilm was developed using a composite of silica-modified QAC(Fixed-Quat) and applied to a fiberglass mesh as an active surface via sol–gel technique. The synthesized Fixed-Quat nanocoating was found to be effective against E. coli with an inactivation rate of 1.3 × 10~(-3) log reduction/cm min. The Fixed-Quat coated fiberglass mesh also demonstrated successful control of Microcystis aeruginosa with more than 99% inactivation after 10 hr of exposure.The developed antimicrobial mesh was also evaluated with wild-type microalgal species collected in a water body experiencing HABs, obtaining a 97% removal efficiency. Overall,the silica-functionalized Fixed-Quat nanocoating showed promising antimicrobial properties for water disinfection and HABs control, while decreasing concerns related to DBPs formation and the possible release of toxic nanomaterials into the environment.     

高藻水臭氧预氧化过程有机物转化及消毒副产物生成势

研究了高藻水预氧化处理过程中,不同臭氧氧化程度及不同pH值条件下,藻类有机物释放与转化规律以及氯化消毒副产物(DBPs)的生成特性.结果表明,臭氧投加量为28.92 mg·L-1时藻去除率达36%.随着臭氧投加量的增加,藻的去除率进一步增加,类腐殖酸先增加后持续减少,溶解性微生物代谢产物、类富里酸和类芳香蛋白物质持续减少;低投加量的臭氧对二氯乙腈(DCAN)、三氯乙腈(TCAN)生成势有明显的控制作用,但会增加三氯硝基甲烷(TCNM)以及1,1,1-三氯丙酮(1,1,1-TCP)前体物,随臭氧投加量增大,DBPs生成势显著增大.酸性条件下臭氧对藻的去除效果最好,UV254以及总有机碳(DOC)均随pH的增大有所上升,但变化较小;臭氧氧化可降解溶解性微生物代谢产物,降解效果受pH影响较小,类腐殖酸有机物随pH值增大而减少;DCAN、TCAN生成势随pH增大有所降低,TCNM生成势在pH=10条件下最高,1,1,1-TCP生成势在pH=7条件下最高.     

Monohalogenated acetamide-induced cellular stress and genotoxicity are related to electrophilic softness and thiol/thiolate reactivity

Haloacetamides(HAMs) are cytotoxic, genotoxic, and mutagenic byproducts of drinking water disinfection. They are soft electrophilic compounds that form covalent bonds with the free thiol/thiolate in cysteine residues through an S_N2 reaction mechanism.Toxicity of the monohalogenated HAMs(iodoacetamide, IAM; bromoacetamide, BAM;or chloroacetamide, CAM) varied depending on the halogen substituent. The aim of this research was to investigate how the halogen atom affects the reactivity and toxicological properties of HAMs, measured as induction of oxidative/electrophilic stress response and genotoxicity. Additionally, we wanted to determine how well in silico estimates of electrophilic softness matched thiol/thiolate reactivity and in vitro toxicological endpoints.Each of the HAMs significantly induced nuclear Rad51 accumulation and ARE signaling activity compared to a negative control. The rank order of effect was IAM BAM CAM for Rad51, and BAM ≈ IAM CAM for ARE. In general, electrophilic softness and in chemico thiol/thiolate reactivity provided a qualitative indicator of toxicity, as the softer electrophiles IAM and BAM were more thiol/thiolate reactive and were more toxic than CAM.     

单过硫酸氢钾复合粉在饮用水消毒过程中的副产物生成特性及遗传毒性变化

以北京田村山净水厂原水和炭后出水作为试验用水,对新型消毒剂单过硫酸氢钾复合粉消毒后生成的消毒副产物(disinfection by-products,DBPs)进行定性分析.向受试水样中分别投加单过硫酸氢钾复合粉和次氯酸钠,比较了复合粉消毒和氯消毒的DBPs生成量,并通过umu试验对水样消毒后的遗传毒性变化进行测试.结果表明,测试水样投加单过硫酸氢钾复合粉消毒前后的有机物种类变化不大,但仍有新的卤代烃和卤代物生成.与氯消毒相比,单过硫酸氢钾复合粉消毒后生成的三卤甲烷(THMs)和卤乙酸(HAAs)的含量更低.另外,根据umu测试的结果,经单过硫酸氢钾复合粉消毒后原水和炭后水的遗传毒性均明显低于氯消毒.然而在水中有机物较多和消毒剂投加量较大时,单过硫酸氢钾复合粉用于消毒仍有一定安全风险.     

污水再生过程中消毒副产物前体物转化规律

采用大孔吸附树脂将污水中的消毒副产物(DBP)前体物分离为亲水性物质(HPI)、强疏水性物质(HPO)和弱疏水性物质(TPI)这3个组分,通过三维荧光光谱、傅里叶红外光谱和核磁共振对再生水处理各沿程前体物进行表征,并测定各沿程出水的消毒副产物生成势(DBPFP).结果表明,生活污水中DBPs前体物主要组分为腐殖质和脂肪烃,以HPI为主.一级处理(沉淀)基于HPO与水互斥的物理性能对疏水性腐殖质有较好的去除效果,腐殖质的去除会导致含碳消毒副产物生成势(CDBPFP)的降低.此外由于DON/DOC的增加,含氮消毒副产物生成势(N-DBPFP)有所增加.二级处理(生物处理)对腐殖质和脂类均有较好的去除效果,但会产生大量疏水性的溶解性微生物产物(SMP),因此生物处理后DBPs前体物主要表现为疏水性.SMP的累积会导致C-DBPFP和N-DBPFP的大幅增加.深度处理(滤布滤池)能截留部分腐殖质和疏水性的SMP,因此前体物HPO占比减少,HPI占比增加.深度处理可以通过对SMP的去除来降低C-DBPFP和N-DBPFP.