轴承生产废水处理工艺的选择与实践

采用絮凝气浮 过滤工艺处理轴承生产废水。工程实践表明,该工艺处理效果稳定、耐冲击负荷、工艺组合合理。预处理后的废水经气浮 过滤工艺处理后,COD、SS、油的去除率分别为80.62%～84.31%、81.00%～84.39%、89.37%～96.45%,出水完全能达到排放标准。     

空气过滤技术研究综述

文章分别从空气过滤材料、空气过滤器、空气过滤理论及空气过滤技术的应用等四个方面,对空气过滤技术进行了详细阐述.总结了空气过滤材料、空气过滤器的分类及研究进展、空气过滤器的过滤机理及过滤理论的发展.介绍了空气过滤技术的主要应用,并指出了空气过滤技术的发展动向和市场趋势.     

Membrane fouling control by ultrasound in an anaerobic membrane bioreactor

In this study, ultrasound was used to control the membrane fouling online in an anaerobic membrane bioreactor (AMBR). Short-term running experiments were carried out under different operating conditions to explore feasible ultrasonic parameters. The experimental results indicated that when the crossflow velocity was more than 1.0 m/s, membrane fouling could be controlled effectively only by hydrodynamic methods without ultrasound. When ultrasound was applied, an ultrasonic power range of 60–150 W was suitable for the membrane fouling control in the experimental system. The experimental results showed that the membrane fouling was controlled so well that membrane filtration resistance (ΣR) could stay at 5 × 10¹¹ m⁻¹ for more than a week with the crossflow velocity of 0.75 m/s, which equaled the effect of crossflow velocity of more than 1.0 m/s without ultrasound. Translated from Techniques and Equipment for Environmental Pollution Control, 2006, 7(4): 25–29 [译自: 环境污染治理技术与设备]     

A／O-化学除磷工艺中DMBR动态膜成膜条件研究

根据动态膜原理，将0．1mm孔径无纺布为膜材的动态膜反应器（Dynamic Membrane BioReactor，DMBR）应用于A／O-化学除磷工艺之中，在动态膜反应器内完成泥水分离。试验测试了曝气强度、初始膜通量和污泥浓度对动态膜成膜的影响。结果表明，曝气强度和初始膜通量是影响成膜的关键性参数。当曝气强度≥60m^3／m^2·h或初始膜通量≥70L／m^2·h，2h内均不能形成截留性能良好的动态膜。在VSS／SS较低的污泥系统中，适宜的成膜条件为：曝气强度≤40m^3／m^2·h；初始膜通量≤40L/m^2·h。     

生物膜反应器处理洗涤污水的试验

介绍了采用生物膜反应器处理洗涤污水的试验研究方法，研究了COD、LAS和NH3-N的去除效果。试验结果表明：整个系统出水稳定，水质良好（COD〈38．7mg／L、NH3-N〈1．1mg／L、LAS〈0．9mg／L，且无色无味、无SS），符合国家建设部生活杂用水回用水质标准，且具有较强的抗冲击负荷能力。在生物膜反应器中，微生物对污染物的去除起主要作用，而中空纤维膜对维持系统的稳定出水起重要作用。     

陶瓷微滤膜过滤黑液的清洗与再生

对无机陶瓷微滤膜过滤草桨黑液的膜清洗及再生的方法进行了研究。考察了物理和化学方法的再生效果、单种清洗剂的清洗效果、复合方法的清洗效果和效果的可重复性。结果表明物理冲洗、高温灼烧、单一的化学清洗剂清洗均可以提高陶瓷膜的再生通量；但是复合方法对陶瓷微滤膜的再生效果较好，其中按氢氧化钠溶液清洗、硝酸溶液清洗、次氯酸钠溶液清洗的实验步骤，膜的再生渗透通量高．且重复性强，可望在工业生产的在线清洗中应用。     

Fulvic acid removal by nanoparticle TiO2 using a submerged membrane photocatalysis reactor

The degradation of fulvic acid（FA） by nanoparticle TiO2 in a submerged membrane photocatalysis（SMPC） reactor was studied. In this reactor, photocatalytic oxidation and membrane separation co-occured. The continuous air supplier provided O2 for the photocatalytical reaction and mixed the solution through an airflow controller. The particle TiO2 could automatically settle due to gravity without particle agglomeration so it could be easily separated by microfiltration（MF） membrane. It was efficient to maintain high flux of membranes. The effects of operational parameters on the photocatalytic oxidation rate of FA were investigated. Results indicated that photocatalyst at 0.5 g/L and airflow at 0.06 m^3/h were the optimum condition for the removal of fulvic acid, the removal efficiency was higher in acid media than that in alkaline media. The effects of different filtration duration on permeate flux rate of MF with P25 powder and with nanoparticle TiO2 were compared. Experimental results indicated that the permeate flux rate of MF was improved and the membrane fouling phenomenon was reduced with the addition of nanoparticle TiO2 catalyst compared with conventional P25 powder. Therefore, this submerged membrane photocatalysis reactor can faciliate potential application of photocatalytic oxidation process in drinking water treatment.     

膜生物反应器膜污染的水力学控制实验研究

叙述了膜污染是影响膜-生物反应器处理技术推广应用的关键因素，采用水动力学方法是控制膜污染的有效方法。在不同污泥浓度条件下。对不同曝气强度下膜污染的发展速率及其形成机理进行了试验研究，研究结果表明：对应于不同污泥浓度均存在一个经济曝气强度，其大小随污泥浓度升高呈线性增加，膜生物反应器在经济曝气强度条件下运行可控制膜污染的发展；并从理论上推导出一个临界污泥浓度，其值为5．15g／L。对应于临界污泥浓度，并且污泥絮体在膜面可形成比较稳定的动态膜，膜过滤压差上升的速率最慢，膜生物反应器在此临界污泥浓度条件下运行膜污染发展最为缓慢。     

铁蓝—活性炭生物膜法处理彩色胶片水洗废水的研究

定影漂白废话水用铁蓝法预处理，结果表明，以硫酸亚铁为沉淀剂，投加量为铁氰化物理论值的１．３倍，ＣＮ去除率为９８％，反应生成的普鲁士蓝纯度较高，可供综合利用，铁蓝法除ＣＮ后的出水与显影冲洗废水混合，再经生炭生物膜法处理，ＣＯＤｃｒ去除率为８０％；     

UV/TiO_2膜深度处理垃圾渗滤液的研究

研究了以固定相TiO2为催化剂光催化降解垃圾渗滤液中有机污染物的可行性。试验了制备TiO2膜的适宜条件以及光照时间等各种因素对COD的去除率和UV335脱色率的影响。研究表明,COD为418mg/L的垃圾渗滤液经400W高压汞灯光照30min,COD的去除率和UV335脱色率分别为44.3%和75.0%。光照时间60min时,COD的去除率和UV335脱色率可提高至54%和90%。光照30min后与活性炭柱联用,COD的去除率和UV335脱色率分别提高到68.3%和84.6%。