表面裂纹对Rayleigh波的滤波特性分析

摘要表面裂纹是危害很大且普遍存在的一种缺陷,严重影响到特种设备的安全运行。对表面裂纹尺寸的测量一直未得到很好的解决,由于Rayleigh波能量主要集中在深度一个波长的范围内,当传播过程中和裂纹相互作用时,其频谱会发生变化,一部分高频波将会被吸收,吸收频率的大小与裂纹的深度密切相关。此时裂纹起了一个类似低通滤波器的作用,这点对于裂纹深度检测具有指导意义。     

On the parameterization of the roughness length for the air-sea interface in free convection

The roughness length at the air-sea interface during free convection (z_0fc) is mainly related to the convective velocity (w_*) rather than the friction velocity (u_*). The parameterization of z_0fc with w _* ² /g as proposed by Abdella and DAlessio in 2003 is evaluated. It is shown that their proposed formula is consistent with field measurements. In order to avoid self-correlation by using u_*, a new parameterization of w_* with wind speed (U_z) at height z and stability parameter (z/L, where L is the buoyancy length) is proposed. This new formula for w_* is in agreement with an independent field result.     

The Surface Roughness of a Rubber Soling Material Determines the Coefficient of Friction on Water-Lubricated Surfaces

For more than a decade, evidence has been accumulating that points to the fact that the microscopic roughness of the footwear soling surface is a major determinant of slip-resistance on lubricated surfaces, but conclusive experimental proof has been lacking. This article describes an experiment in which five pairs of shoes were soled with the same rubber compound. Four of the pairs were abraded by different grades of grit to produce a range of roughness values. The coefficient of friction (CoF) of the five solings was then measured repeatedly by the walking traction method on wet surfaces including glazed wall tiles, vinyl asbestos coated with the wax floor polish, and both sides of a sheet of float glass. The Kruskal-Wallis statistical test proved beyond doubt that the soling roughness is a major factor in determining the CoF of this rubber soling material; p < 10⁻⁵. Nearly all of the grip was due to surface roughness of the soling material on these atypically smooth floors, although the surface roughness of the floors also had a significant effect on CoF; p < 0.003. Float glass is shown to be a promising reference floor material for the measurement of CoF of footwear; there was no statistical difference between results for the two sides of the glass sheet. Float glass could be used in the development of a standard CoF test method because new sheets of glass from the same manufacturer are identical and extremely smooth. The specification of CoF values for solings/floors combinations in lubricated conditions is of little value unless associated with roughness measurements and knowledge of how wear will affect the surface roughness of the sole. This article reports the first evidence that any specification of flooring by measuring CoF based on dry surfaces could lead to an increase in the number of injuries caused by slipping on the wet surfaces. Published by Elsevier Science Ltd     

改性ACF－PAN吸附SO_2前后表面结构变化及机机理究

以自制ＰＡＮ－基聚丙烯腈活性碳纤维ＡＣＦ－ＰＡＮ（ＡＣＦ－活性碳纤维、ＰＡＮ－聚丙烯腈）和改性处理的ＡＣＦ－ＰＡＮ吸附ＳＯ_２，借助ＩＲ、ｘ－光电子能谱分析等研究ＡＣＦ－ＰＡＮ改性处理及吸附ＳＯ_２前后表面结构变化。结果表明：各型ＡＣＦ－ＰＡＮ吸附ＳＯ_２的活性中心为表面结构中的含氮官能团以及引入的金属氧化物，其吸附机理是活性氮催化或电子传递。     

REST-Rossendorf expert system for surface and sorption thermodynamics

This paper presents a digitized version of a thermodynamic sorption database, implemented as a relational database with MS Access. It is mineral-specific and can therefore be used for additive models of complex solid phases such as rocks or soils. An integrated user interface helps users to access selected mineral and sorption data, to extract internally consistent data sets for sorption modeling, and to export them in formats suitable for other modeling software. Data records comprise mineral properties, specific surface area values, surface binding sites' characteristics, sorption ligand information, and surface complexation reactions. An extensive bibliography is included, providing links not only to the above listed data, but also to background information concerning surface complexation model theories, evidence for surface species, and sorption experimental techniques.     

Estimation of surface area of montmorillonite by ethylene oxide chain adsorption

This study investigates the feasibility of using ethylene oxide chain adsorption to determine the surface area of an expandable clay, montmorillonite. Experimental results indicate that high molecular weight poly(ethylene oxide) or nonionic surfactant with long ethylene oxide chain should be used to provide reasonable estimations for monolayer capacity. The method has advantages over Brunauer, Emmett, and Teller method in that it is readily applicable to a wide range of areas, particularly to 2:1 layer silicates under aqueous conditions.     

利用水泥处理垃圾渗滤液生物处理出水的研究

利用水泥的表面吸附和水化反应性质处理垃圾渗滤液生物处理出水可以取得很好的效果,COD的去除率可达69.5%.处理效果与水灰比、反应时间密切相关,低水灰比和较长反应时间对COD的去除更为有利.对处理前后水样的COD和TOC分析表明,水泥对非TOC贡献的COD有很强的去除效果.     

Surface complexation modeling of Yb(III) sorption and desorption on hematite and alumina

Sorption and desorption of Yb(III) were studied on hematite and on alumina using a surface complexation model. The experimental methodology was conceived to allow an analysis of the data using a constant capacitance model. The FITEQL code was used for the calculations.The experimental results tend to show reversibility of sorption when the surface loading is small, and irreversibility when the surface loading is high. Surface complexation modeling gives a good interpretation of these two phenomena, taking into account hydroxylation of the surface complexes. In these two cases, it is possible to describe sorption and desorption curves with the same surface stoichiometries and the same surface complexation constants. The existence of these surface complexes depends on the pH of the solution, surface loading, and reaction direction.     

A new approach for modelling potential effects in cation adsorption onto binary (hydr) oxides

The current approach for modelling ion adsorption onto binary (hydr)oxides using homogeneous surface complexation models involves the assumption of either an ideal mixture of the two surfaces (i.e. two surface sites on one surface) or a patchwise surface (i.e. two surfaces with one surface site on each surface). As the physical truth should be between these two limiting cases, a model which assumes a patchwise surface constituted of three patches is proposed. Two patches represent the distinct (hydr)oxides, and the third one a mixture of these distinct (hydr)oxides. Using the diffuse layer model, the three approaches are applied to literature data for Cd adsorption onto binary mixtures of alumina-coated silica at total constant Cd concentration and varying amounts of alumina coatings. For Cd adsorption onto these binary (hydr)oxide systems, the new approach explains the observed potential effects. The proposed model, which contains two additional adjustable parameters in terms of site concentrations or one adjustable parameter in terms of specific surface area, is more successful than the two limiting cases. The new model is then validated by predicting Ca and Zn behaviour on the same binary (hydr)oxide system.     

Determination of 4-tert-octylphenol, 4-nonylphenol and bisphenol A in surface waters from the Haihe River in Tianjin by gas chromatography-mass spectrometry with selected ion monitoring

The estrogenic pollutants 4-tert-octylphenol (OP), 4-nonylphenol (NP) and bisphenol A (BPA) were determined in surface water samples from the Haihe River, Tianjin, China. The analytes were extracted and concentrated from 300 ml acidified water samples by liquid–liquid extractions using dichloromethane, derivatized with trifluoroacetic anhydride, and quantified by gas chromatography–mass spectrometry (GC–MS) with selected ion monitoring (SIM). Among the samples collected from 14 sampling sites, only one sample was found to have a relatively high concentration of BPA (8.30 μg l⁻¹) and NP (0.55 μg l⁻¹). The concentrations of OP, NP and BPA in the other samples were in the range of 18.0–20.2, 106–296 and 19.1–106 ng l⁻¹, respectively. Recoveries for OP, NP and BPA in the spiked water samples were all over 80%.