水溶液中臭氧和溴离子的反应研究

为探明O3氧化Br-的反应机制,采用离子色谱、PDA紫外-可见光度仪研究了水中Br-被O3氧化的反应过程.离子色谱分析表明,被氧化的Br-中只有约10%被O3氧化成BrO3-.进一步研究表明,除了生成BrO3-外,Br-被O3氧化过程中还产生了Br2,Br2又与溶液中存在的Br-结合形成Br3-,并首次得到了Br3-的吸收光谱,测得Br3-的最大吸收峰λmax为260 nm,提出了Br-与O3的基元反应.该研究补充和完善了O3氧化Br-的反应机制,也为O3处理含Br-水时Br-的归趋提供了有益信息.     

Cost-performance analysis of nutrient removal in a full-scale oxidation ditch process based on kinetic modeling

A full-scale oxidation ditch process for treating sewage was simulated with the ASM2d model and optimized for minimal cost with acceptable performance in terms of ammonium and phosphorus removal. A unified index was introduced by integrating operational costs (aeration energy and sludge production) with effluent violations for performance evaluation. Scenario analysis showed that,in comparison with the baseline (all of the 9 aerators activated), the strategy of activating 5 aerators could save aeration energy significantly with an ammonium violation below 10%. Sludge discharge scenario analysis showed that a sludge discharge flow of 250–300 m3/day (solid retention time (SRT), 13–15 days) was appropriate for the enhancement of phosphorus removal without excessive sludge production. The proposed optimal control strategy was: activating 5 rotating disks operated with a mode of "111100100" ( "1"represents activation and "0" represents inactivation) for aeration and sludge discharge flow of 200 m3/day (SRT, 19 days). Compared with the baseline, this strategy could achieve ammonium violation below 10% and TP violation below 30% with substantial reduction of aeration energy cost (46%) and minimal increment of sludge production (< 2%). This study provides a useful approach for the optimization of process operation and control.     

三槽氧化沟内底推位置与积泥厚度的分析研究

氧化沟工艺由于进水中含有大量的无机颗粒,无机颗粒的沉淀导致沟内积泥较厚。为了不影响正常生产,依据经验数据,依次对1号、2号氧化沟安装底推。对沟内积泥情况及影响因素进行分析比较,得出氧化沟的积泥主要由进水中密度较大的无机颗粒造成,且积泥规律与底推安装位置和运行情况相关。     

Supercritical water oxidation of polyvinyl alcohol and desizing wastewater：Influence of NaOH on the organic decomposition

Polyvinyl alcohol is a refractory compound widely used in industry. Here we report supercritical water oxidation of polyvinyl alcohol solution and desizing wastewater with and without sodium hydroxide addition. However, it is difficult to implement complete degradation of organics even though polyvinyl alcohol can readily crack under supercritical water treatment. Sodium hydroxide had a significant catalytic effect during the supercritical water oxidation of polyvinyl alcohol. It appears that the OH ion participated in the C-C bond cleavage of polyvinyl alcohol molecules, the CO2-capture reaction and the neutralization of intermediate organic acids, promoting the overall reactions moving in the forward direction. Acetaldehyde was a typical intermediate product during reaction. For supercritical water oxidation of desizing wastewater, a high destruction rate (98.25%) based on total organic carbon was achieved. In addition, cases where initial wastewater was alkaline were favorable for supercritical water oxidation treatment, but salt precipitation and blockage issues arising during the process need to be taken into account seriously.     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

Fenton氧化技术在废水处理方面的应用

Fenton氧化技术是高级氧化技术的一种,是处理难降解的废水是常用的技术之一。本文对Fenton氧化技术原理和影响因素进行分析,并对Fenton氧化技术在电镀废水、染料废水、造纸废水中的应用进行了研究。     

非均相类Fenton试剂的制备及其在焦化废水处理中的应用研究

利用浸渍法,将Fe3＋负载在经酸碱改性后的粉状活性炭上,当浸渍液浓度为2．5％,固化温度为270℃时,制成的催化剂催化活性较高。用自制的非均相类benton试剂降解焦化废水,通过正交试验和极差分析得出,影响因素的主次顺序为催化剂用量〉初始pH值〉反应时间〉H：0：投加量。结果表明,在100ml水样中。室温条件下,初始pH值为4．0,催化剂使用量为1．5g,H20：投加量为5ml（分两次投加）,反应时间为90min时,COD去除率可达99％。采用混凝＋化学沉淀＋非均相类Fenton试剂法处理焦化废水,各主要出水水质指标为：色度lO倍;COD浓度38．5mg／L;氨氮浓度8．4mg／L,达到国家一级排放标准。     

氧气热处理的TiO2纳米管阵列光电催化降解亚甲基蓝的研究

采用原位阳极氧化法在Ti基底上制备了高度有序的TiO2纳米管阵列薄膜,SEM图像表明TiO2纳米管定向排列整齐,分布均匀,其管径范围在70～100 nm.XRD结果证明,阳极氧化法制备的TiO2纳米管为无定型晶型,经退火后为具有良好光催化活性的锐钛矿型.以亚甲基蓝（methylene blue）为目标物研究了TiO2纳米管光电催化性能及影响因素,结果表明,以0.1 mol/L NaCl为电解质,在氧气热处理气氛下,外加偏压为0.5 V、pH=3.25、光照强度为1 000μW/cm2、纳米管薄膜表面积为2 cm×2 cm且MB初始浓度为10 mg/L的条件下,TiO2纳米管阵列薄膜光电催化降解MB的降解效率可达99.56%.电化学阻抗谱分析显示,光电催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

芬顿氧化试验中残余双氧水对CODcr测定的影响研究

在采用Fenton高级氧化技术对垃圾压滤液进行处理时,作为氧化剂的双氧水经常不能完全消耗。而使用重铬酸钾法进行CODcr测定时,待测水体中残余的双氧水会表现出还原性而消耗重铬酸钾,对最终CODcr测定结果产生影响。本文分析了在垃圾压滤液中不同浓度双氧水对CODcr测定的影响大小,得出双氧水浓度对CODcr影响曲线,同时为消除双氧水对CODcr测定结果影响,在试验中投加过量硫酸亚铁与双氧水反应,当投加量达到理论反应量的1.0～1.2倍时,对双氧水去除效果最好,使后续的CODcr测定试验更加准确。