The relationship between oxygen consumption rate and temperature during coal spontaneous combustion

Spontaneous combustion is a major natural disaster in coal production. In the process of exploring coal self-ignition, a series of hypotheses have been put forward, most scholars agree that the current coal-oxygen compound theory. Oxygen consumption rate reflects the status of coal spontaneous combustion, and it is also one of the parameters necessary for numerical simulation of coal spontaneous combustion. In this paper, a coal heating and oxidation experiment was designed, Experimental device consists of heating and oxidation furnace, gas chromatograph, temperature control and data acquisition systems and other equipment components. Three coal samples whose weight each is 5 g were selected for the study. By experiment, oxygen concentration at the inlet and outlet of temperature oxidation furnace was measured. Oxygen consumption rate is calculated in the heating process of coal according to air flow. In the Cartesian coordinate system, the temperature as abscissa and the oxygen consumption rate for the longitudinal coordinates, drawing the relationship between oxygen consumption rate and temperature plot. And then regression analysis was used to analyze the relationship between oxygen consumption rate and coal temperature during the heating and oxidation process of coal. The results show that the oxygen consumption rate and temperature of coal were linear relationships both before and after the critical temperature when the coal temperature is less than 180 °C. Before the critical temperature oxygen consumption rate is low, however it increases rapidly when coal temperature reaches a critical temperature. The result is important for the prevention and treatment of spontaneous combustion of coal.     

相对速率法测氯原子与一系列低碳醇的反应速率常数

在 2 92± 1K温度和 1 0 1× 10 5Pa压力下 ,以丙烷为参照物 ,采用相对速率方法测定了一系列醇与氯原子在气相中的反应速率常数 ,这些醇与氯的反应速率常数分别为 (单位 :10 7m3·mol-1·s-1) :甲醇k1=3 2 9,乙醇k2 =6 14,正丙醇k3=8 97,异丙醇k4 =4 0 0 ,正丁醇k5=11 7,异丁醇k6=12 5 ,叔丁醇k7=2 0 5 ,正戊醇k8=15 8,异戊醇k9=12 3     

Oxidation inhibition of sulfite in dual alkali FGD system

A laboratory-scale well-mixed thermostatic reactor with continuously blasting air was used to investigate the oxidation inhibition of sulfite in dual alkali flue gas desulfurization （FGD） system. The effects of operating parameters such as pH value and catalyst concentration on the oxidation were studied. Sodium thiosulfate was used in the system, and was found that it significantly inhabited the sulfite oxidation. In the absence of catalyst, sodium thiosulfate at 12.67 mmol/L had an inhibition efficiency of approximately 98%. While in the presence of catalyst, sodium thiosulfate at 26.72 mmol/L had an inhibition efficiency less than 85.0%. The oxidation reaction order of sulfite in the sodium thiosulfate was determined to be -1.90 and 4）.55 in the absence and presence of the catalyst, respectively. Apparent activation energy of oxidation inhibition was calculated to be 53.9 kJ/mol. Pilot tests showed that the consumption rate of thiosulfate agreed well with the laboratory-scale experimental results.     

青海共和盆地降尘观测与137Cs测定的初步结果

通过对1998～1999年共和盆地的降尘观测和尘样的¹³⁷Cs分析,测定了降尘速率及其月分配;对尘源进行了¹³⁷Cs示踪,并从理论上估算出降尘产生的¹³⁷Cs再分配,对沉积速率的计算模型进行了讨论.作为采用¹³⁷Cs法研究沙尘暴降尘的一次尝试,这些初步结果对沙尘暴测定及其强度评估等方面研究有一定的借鉴作用.     

活性污泥数学模型中异养菌产率系数的测定研究

利用活性污泥数学模型预测污水生物处理系统,首先必须确定其参数和水质组分。采用间歇活性污泥法和呼吸计量法对活性污泥数学模型中异养菌产率系数γ_H进行测定研究。结果表明,间歇活性污泥法测定结果重现性较差,试验控制条件比较严格;呼吸计量法测定结果准确性较高,重现性良好,因而,呼吸计量法是比较可行的γ_H测定方法。     

低铬油套管钢材在不同工况下的腐蚀规律研究

目的 研究低铬油套管钢材在不同腐蚀环境中的腐蚀特征。方法 采用高温高压动态反应釜对1Cr、3Cr这2种常用低铬油套管钢材进行纯CO2、CO2和低浓度H2S共存条件下的腐蚀试验。结果 温度在40~80 ℃条件下,各种钢材的腐蚀速率随着温度的升高而变大。加入低浓度H2S后,可以抑制CO2腐蚀,且随着温度升高,抑制性逐渐减弱。分析认为,在单独CO2环境以及CO2和低浓度H2S共存的环境中,1Cr、3Cr钢表面出现铬富集现象,形成的Cr(OH)3膜保护基底。同时,在CO2和低浓度H2S共存的环境中,1Cr、3Cr钢表面形成致密的FeS产物膜有助于保护基底,抵抗Cl^－侵蚀。结论 低Cr钢表面因铬的富集形成钝化膜,能有效抑制油套管的腐蚀速率,以上研究成果对CO2和低浓度H2S环境中的腐蚀理论以及油田油套管材料合理选择均有一定指导意义。     

高温高含二氧化碳条件下五种含Cr钢适用性评价

目的 预测某高温高含二氧化碳油井中管柱的腐蚀情况,为该油井推荐安全经济的材质。方法 采用高温高压反应釜模拟现场工况进行腐蚀试验,通过失重法、扫描电子显微镜(SEM)和X射线能谱分析(EDS)对五种含Cr钢的适用性进行评价。结果 在40~160 ℃温度范围内,五种钢材随温度的升高,其均匀腐蚀速率先升高后降低,且均在80 ℃时达到最大值。3Cr钢的腐蚀速率最高,在整个温度范围内,均远高于0.076 mm/a。在温度为120 ℃时,9Cr钢开始出现局部腐蚀。在温度为160 ℃时,13Cr钢有一定的局部腐蚀倾向。S13Cr、22Cr钢在整个温度范围内的腐蚀速率都较低,试验后试样表面平整连续,耐蚀性能好。结论 建议在采出井井筒中上部40~80 ℃较低温度井段选用9Cr钢,中部80~120 ℃中高温井段选用13Cr钢,底部120~160 ℃高温井段选用S13Cr钢。     

聚糖原菌富集实验及其内源过程探究

细胞衰减是微生物内源过程的一个重要组成部分,可分为由细胞死亡引起的数量衰减和由细胞活性降低引起的活性衰减两部分.通过挥发性脂肪酸（VFA）吸收速率(VFAUR)测定、荧光原位杂交技术（FISH）以及LIVE/DEAD细胞染色技术,研究了富集聚糖原菌（GAOs）在序批式反应器（SBR）系统中好氧环境下的衰减特征.结果表明,当T=30℃、进料中m(COD)∶m(P)=100时,SBR系统中GAOs富集比例达94%.测定和计算表明,SBR富集系统中GAOs衰减速率和死亡速率分别为0.132 d^-1和0.034 d^-1,其数量衰减和活性衰减占其细胞总衰减比例分别为26%和74%.可见,GAOs数量衰减只占其细胞总衰减中很小一部分,而绝大部分衰减由活性衰减所引起.     

内蒙古癌死亡率与土壤环境中化学元素的关系

利用中国癌死亡率与土壤环境中化学元素的相关性研究成果，研究了内蒙古癌死亡率与土壤环境中化学元素：As、Cd、Co、Cu、Hg、Mn、Ni、Pb、Se、V、Li、Na、K、Rb、Cs、Mg、Ca、Sr、Ba、B、Al、Ga、In、Tl、Sc、Y、La、Ce、Pr、Nd、Tb、Dy、Ho、Er、Tm、Yb、Lu、Th、U、Sn、Ti、Zr、Hf、Sb、Bi、Ta、Te、Mo、W、Br、I、Fe等52个元素含量的关系。     

BAF去除氨氮关键影响因素研究

为探讨曝气生物滤池去除氨氮的关键因素,选取沈阳仙女河污水处理厂(40万t/d)现场进行实地研究。通过测定不同条件下(pH、进水COD浓度、溶解氧、温度、水力负荷)的氨氮去除率,并进行主成分分析结果显示,影响BAF工艺脱氮的关键因素是温度、溶解氧和水力负荷。当温度在14~30℃之间时,氨氮的去除率一直维持较高,当温度低于14℃时,氨氮的去除率较低;随着溶解氧浓度的增大,氨氮的去除率也随之升高,当溶解氧增加到5.6 mg/L时,氨氮的去除率达到80%~90%,接近饱和状态;在水力负荷为3.08~4.15 m3/(m.2h)之间时,氨氮的去除率上升,超过该值,则氨氮去除率下降。