Chemical composition and properties of ashes from combustion plants using Miscanthus as fuel

Miscanthus giganteus is one of the energy crops considered to show potential for a substantial contribution to sustainable energy production. In the literature there is little data available about the chemical composition of ashes from the combustion of Miscanthus and practically no data about their physical properties. However, for handling, treatment and utilization of the ashes this information is important. In this study ashes from two biomass combustion plants using Miscanthus as fuel were investigated. The density of the ashes was 2230 ± 35 kg/m~3, which was similar to the density of ashes from straw combustion. Also the bulk densities were close to those reported for straw ashes. The flowability of the ashes was a little worse than the flowability of ashes from wood combustion. The measured heavy metal concentrations were below the usual limits for utilization of the ashes as soil conditioner. The concentrations in the bottom ash were similar to those reported for ash from forest residue combustion plants. In comparison with cyclone fly ashes from forest residue combustion the measured heavy metal concentrations in the cyclone fly ash were considerably lower. Cl-, S and Zn were enriched in the cyclone fly ash which is also known for ashes from wood combustion. In comparison with literature data obtained from Miscanthus plant material the concentrations of K, Cl-and S were lower.This can be attributed to the fact that the finest fly ash is not collected by the cyclone de-dusting system of the Miscanthus combustion plants.     

基于环境因子和邻近信息的土壤属性空间分布预测

为探索乡镇尺度上土壤属性空间分布预测的最佳方法,以江西省万年县齐埠镇为例,借助四方位搜索法、地统计学和遥感影像分析技术提取环境因子（地形因子和植被覆盖指数）和邻近信息[w（有机质）与w（速效钾）],构建OK法（普通克里金法）、RK1法（仅基于环境因子的回归克里金法）以及RK2法（基于环境因子和邻近信息的回归克里金法）对齐埠镇耕地表层（0~20 cm）土壤w（有机质）、w（速效钾）空间分布进行预测.结果表明:齐埠镇土壤w（有机质）平均值为35.03 g/kg,w（速效钾）平均值为96.73 mg/kg,均为中等空间变异性.对62个样点进行建模,16个测试样点进行独立验证的误差分析表明,RK2法对土壤w（有机质）、w（速效钾）预测结果的均方根误差、平均绝对误差和平均相对误差较OK法分别降低了18.05%、18.01%、21.77%和7.25%、9.49%、9.84%;较RK1法分别降低了22.48%、20.91%、22.02%和9.27%、12.61%、13.52%.研究显示,RK2法明显提高了土壤w（有机质）、w（速效钾）空间分布模拟精度,并且存在改进和提高的空间.      

外源Ca2+对SBR启动期活性污泥胞外多聚物的动态影响

利用无机物如Ca~(2+),加快活性污泥反应器启动,强化活性污泥絮体性能和结构稳定性,受到越来越多的重视.采用序批式反应器,研究进水中添加Ca~(2+)对反应器启动期活性污泥沉降性能和胞外多聚物的影响.结果表明运行至28 d,与进水中不添加Ca~(2+)的反应器(对照反应器)相比,进水中添加150 mg·L~(-1)外源Ca~(2+)的反应器中活性污泥MLSS和MLVSS值分别高出了89.6%和75.6%,SVI值则降低了47.9%;活性污泥胞外多聚物总量增加了76.4%,多糖增加了28.8%,蛋白质减少了31.6%,添加150 mg·L~(-1)外源Ca~(2+)的反应器中污泥胞外多聚物中多糖/蛋白质值为68.8,对照反应器的活性污泥胞外多聚物多糖/蛋白质值仅为36.6.三维荧光光谱和红外光谱分析表明外源Ca~(2+)导致活性污泥胞外多聚物组分发生了变化.实验结果为进水中添加外源Ca~(2+)改善活性污泥沉降性能提供了基础数据.     

模型模拟土壤性质和植被种类对再生水灌溉水盐运移的影响

为推动再生水安全灌溉,本研究运用ENVIRO-GRO模型模拟了不同土壤性质、植被条件下土壤盐分的分布规律及累积趋势,探讨了土壤性质和植被种类对再生水灌溉水盐运移的影响.研究发现,不同土壤初始含盐量下,经多年重复模拟后最终达到统一的平衡状态;而不同土壤质地下,随着灌溉年份的增加,壤土、黏壤土中的土壤ECe年均值逐渐增加直到平衡,砂壤土中的土壤ECe年均值逐渐减少直到平衡,平衡时土层中的ECe值砂壤土〈壤土〈黏壤土.3种植被下,大叶黄杨、油松的土壤ECe值增加量小于早熟禾;土壤盐分在土层中的空间、时间分布也均有所不同.此外,不同模拟情景下,土壤盐分累积都不会影响植被的生长（黏壤土除外）,但均出现轻度盐渍化（砂壤土除外）.     

北京不同污染事件期间气溶胶光学特性

利用2005~2011年的AERONET观测数据,对北京不同污染事件期间(秸秆焚烧、烟花燃放以及沙尘天气)气溶胶光学特性进行了分析.气溶胶光学厚度受污染有显著上升,沙尘、秸秆、烟花气溶胶的AOD440 nm分别是干净背景的4.91、4.07、2.65倍.AOD与ngstrm波长指数的匹配能够较好地识别污染类型,沙尘对应高AOD和低α,烟花气溶胶α(1.09)稍低于秸秆(1.21)以及背景(1.27),表明烟花气溶胶的粗粒子更占优,秸秆对应更高的AOD则与其中黑碳颗粒较强的消光能力有关.单次散射反照率对波长敏感性不高,沙尘气溶胶的ω值(0.934)高于背景值(0.878)、秸秆气溶胶(0.921)以及烟花气溶胶(0.905),秸秆气溶胶受烟羽老化、吸湿性增长等影响表现出偏大现象.气溶胶粒子谱分布在背景与污染期间均为双峰模态,细模态和粗模态的峰值浓度半径分别为0.1~0.2μm以及2.24~3.85μm,粗细粒子浓度比值由小到大依次为背景(1.04)、秸秆焚烧(1.10)、烟花燃放(1.91)以及沙尘气溶胶(4.96).     

苦草(Vallisneriaspiralis)对城市缓流河道黑臭底泥理化性质的影响

以苦草(Vallisneria spiralis)和城市缓流河道黑臭底泥为研究对象采用模拟实验方法,探讨了苦草对城市缓流河道黑臭底泥理化性质的影响.结果表明,苦草可以显著改善城市缓流污染河道底泥氧化还原环境.实验期间表层底泥Eh从-70 mV升高至90 mV;减少致黑物质亚铁的含量,实验组表层底泥降低25%,而对照却升高38%;促进铁、硫的自然循环,防止亚铁、H2S的累积;明显改善底泥黑臭现象,实验组表层底泥第7 d出现约3 mm厚灰黄色氧化层,氧化层随时间推移逐渐增厚,第28 d厚度为11 mm.该氧化层无明显恶臭气味.对照则在实验第14 d出现1 mm氧化层并维持至实验结束,期间恶臭气味未消减;种植苦草可显著提高沉积物致密程度,降低底泥含水率,有效改善表层底泥流动状态,且在段头浜、河湾、人工湿地景观等处不影响防汛等功能,对减少河道底泥冲刷迁移和抑制黑臭物质悬浮具有积极的生态学意义.     

磺胺甲噁唑对猪粪堆肥过程中堆料性质与酶活性的影响

以猪粪、小麦秸秆为材料,研究了磺胺甲噁唑（SMZ）对高温堆肥过程中理化性质（温度、pH值、E₄/E₆）和酶活性（纤维素酶、磷酸酶、脲酶、多酚氧化酶）的影响.结果表明：SMZ对堆肥理化性质的影响与其浓度有关.高浓度（95 mg·kg^-1）SMZ会对微生物活性产生显著抑制作用,表现出堆肥温度难以达到无害化标准,堆料pH值较低（<9.0）.但高浓度（95 mg·kg^-1）SMZ能激活多酚氧化酶活性,且水提浸液E₄/E₆值较低.在堆肥过程中,SMZ对纤维素酶和脲酶活性呈现出“抑制-激活-抑制”的作用,50 mg·kg^-1的SMZ对纤维素酶产生不同程度的激活作用.相比之下,脲酶活性对SMZ的敏感性比纤维素酶更敏感,5 mg·kg^-1的SMZ即能显著抑制脲酶活性,中浓度（50 mg·kg^-1）的SMZ对碱性磷酸酶活性产生了显著的抑制作用.综上,SMZ通过影响酶活性而影响堆肥过程的物质转化.此外,SMZ浓度越大,种子发芽指数越低.当SMZ≥50 mg·kg^-1时,堆肥难以腐熟而对植物毒性较大.     

改性壳聚糖CAD与微生物絮凝剂MBF8复配絮凝研究

采用水溶液自由基聚合反应,将丙烯酰胺(AM)、二甲基二烯丙基氯化铵(DMDAAC)接枝到壳聚糖分子上制成了阳离子改性壳聚糖(CAD).经FT-IR、XRD、zeta(ξ)电位、凝胶色谱等分析确定,CAD为淡黄色透明液体,pH值为3.7,相对分子质量为2.88×10⁶,阳离子度为16.7,等电点(0.1%溶液)约为pH值10.5,有效成分2.6%,主要特征官能团有羟基、氨基、季铵基和酰胺基, 呈不规则晶体结构.将CAD与相对分子质量3.67×10⁵的多糖类电负性微生物絮凝剂MBF8复配,对浊度12~460 NTU、离子强度3.0 mmol·L^-1的高岭土悬浊液进行烧杯实验.结果表明,MBF8与CAD的最佳使用方式为先投加MBF8后投加CAD,复配比5:3时效果最好,适用的pH范围为6.0~10.0.采用PAC(3.0 mg·L^-1)+MBF8+CAD(1.0 mg·L^-1)复配絮凝,pH=8.0下,对浊度为110 NTU的高岭土悬浊液,浊度去除率>97%,残余铝<0.08 mg·L^-1,絮体大、沉降快,絮凝效果优于PAC+分子量800万、1200万的阴离子PAM及分子量1500万的阳离子PAM.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

几种牺牲阳极在干湿交替条件下的自放电行为比较

模拟海水与空气的干湿交替条件,对四种海船常用牺牲阳极的自放电行为进行了研究。通过测定工作电位、发生电流、溶解性能、溶解产物成分,分析了四种牺牲阳极在经历不同间浸工作周期后的电化学性能,特别是再活化性能。结果表明:在干湿交替条件下,Zn-Al-Cd阳极的电化学性能降低幅度最大,Al-Zn-In-Cd阳极次之,它们均不适合在此环境中使用;Al-Zn-In-Mg-Ti的电化学性能比前两者好,Al-Zn-In-Mg-Ga-Mn则最适合作为干湿交替环境中的牺牲阳极。