污泥厌氧消化技术的研究与进展

厌氧消化是目前国际上应用最为广泛的污泥稳定化和资源化的方法,随着全球性的能源危机以及各国可持续发展和环保法规的相继出台,该技术将有更加广阔的发展前景。阐述了厌氧消化的基本原理和应用情况,讨论了近年国外针对厌氧消化预处理技术和不同运行条件对厌氧消化反应效果的影响以及不同污泥处理工艺产能效果等方面研究成果及最新进展。     

活性炭多维电极法处理活性染料模拟废水的机理研究

以活性嫩黄K-4G染料模拟废水为处理对象,探讨了多维电极系统处理活性染料废水时色度、COD降解的效果和机理。结果表明,活性炭多维电极法对染料废水的处理效果优于单纯电解法和单纯活性炭吸附法;氧化和还原作用对染料的色度和COD去除效果相差不大;增大处理系统中溶液的循环流量可显著改善活性炭多维电极系统对COD和色度的去除效果。     

城市污泥两相厌氧消化沼气产量的技术分析

城市污水处理厂所产生的污泥,数量巨大,成分复杂。如何经济、有效地加以利用已成为目前环境工程中深为关注的课题之一。文章探讨了污泥资源化工作中厌氧消化工艺的温度、时间、污泥成分的最佳工艺备件和沼气产生量,以实现污泥工业化利用。     

包埋固定化微生物的特性研究

文章通过实验研究了PVA与海藻酸钠混合载体包埋固定化微生物系统降解有机物的过程,并对其特性进行了分析。结果发现运行初期凝胶体有凝胶溶出现象,第一天凝胶有机物溶出高达2 173 mg,随后溶出量减少,7～8天溶出停止;同时发现包埋后的微生物活性有损伤和恢复的过程,损伤时相对活性为0.27经过恢复可达到0.85;另外,凝胶的粒径和比重等物理特性也随时间变化,最后趋于稳定。一年多运行实验发现包埋凝胶体的抗持久性也较好。这些特性的探讨将为工程应用提供理论指导。     

Mechanical performance and capillary water absorption of sewage sludge ash concrete (SSAC)

Disposal of sewage sludge from waste water treatment plants is a serious environmental problem of increasing magnitude. Waste water treatment generates as much as 70 g of dry solids per capita per day. Although one of the disposal solutions for this waste is through incineration, still almost 30% of sludge solids remain as ash. This paper presents results related to reuse of sewage sludge ash in concrete. The sludge was characterised for chemical composition (X-ray flourescence analysis), crystalline phases (X-ray diffraction analysis) and pozzolanic activity. The effects of incineration on crystal phases of the dry sludge were investigated. Two water/cement (W/C) ratios (0.55 and 0.45) and three sludge ash percentages (5%, 10% and 20%) per cement mass were used as filler. The mechanical performance of sewage sludge ash concrete (SSAC) at different curing ages (3, 7, 28 and 90 days) was assessed by means of mechanical tests and capillary water absorption. Results show that sewage sludge ash leads to a reduction in density and mechanical strength and to an increase in capillary water absorption. Results also show that SSAC with 20% of sewage sludge ash and W/C = 0.45 has a 28 day compressive strength of almost 30 MPa. SSAC with a sludge ash contents of 5% and 10% has the same capillary water absorption coefficient as the control concrete; as for the concrete mixtures with 20% sludge ash content, the capillary water absorption is higher but in line with C20/25 strength class concretes performance.     

FND- CASS工艺处理城市污水的试验研究

为进一步提高循环式活性污泥工艺(CASS)的脱氮除磷效果,改变其运行方式,采用好氧脉冲曝气,提出频繁硝化-反硝化循环式活性污泥工艺(FND-CASS).结果表明,FND-CASS工艺与CASS工艺相比,在去除污水中有机物方面能力略有下降,但在脱氮除磷方面具有明显的优势.在同样的进水流量且DO浓度控制较低的运行条件下,F...     

使用撬装式生物反应器处理含油污泥的现场试验

以长庆油田华池作业区93#井场的修井油泥为对象,添加石油降解菌剂、营养盐、膨松剂,使用撬装式生物反应器控制反应温度及提供全面的机械搅拌增进溶氧量与营养物质的传递速率,对初始含油量为7.24%的含油污泥进行24d的生物强化降解后,含油量下降为0.23%。结果表明,使用撬装式生物反应器可以使微生物快速高效的降解石油污染物,...     

CAST工艺高温短程硝化的实现及其除磷性能

以模拟废水为研究对象,考察了22、25、28℃这3个温度下CAST反应器内短程硝化的实现及其除磷性能.结果表明,不同温度下系统的TN去除均稳定在80%以上,且NH_4~+-N去除良好.当温度为22℃和25℃时系统内未观察到亚硝积累,除磷率为94. 3%和86. 9%,升高温度至28℃,反应器内亚硝积累率为87. 2%,实现稳定的短程硝化.此外,高温短程硝化阶段(28℃),系统释、吸磷能力较22℃和25℃均有所下降,且厌氧段释磷量/COD消耗量(P/C)比明显低于前两个阶段.然而,该温度条件下反应器除磷性能并未恶化,除磷率为68. 9%,说明进水碳源充足不仅能保证CAST工艺对TN的去除,同时可用于解毒NO_2~-以减弱其对聚磷菌的抑制.不同温度条件下的污泥吸磷小试发现,O_2、NO_3~-、NO_2~-均可作为电子受体进行吸磷,其中好氧吸磷速率高于以NO_3~-和NO_2~-为电子受体的反硝化吸磷速率,且以O_2和NO_3~-为电子受体的吸磷速率与温度呈负相关.     

不同预处理方法促进剩余污泥发酵制氢研究进展

综述了剩余污泥发酵制氢的底物预处理方法,主要包括物理法（热水解法、微波法、超声波法、冻融法）;化学法（酸碱预处理、臭氧氧化法）;生物法（生物强化技术、生物酶法）,分析比较了不同预处理方法的剩余污泥发酵制氢体系的氢气含量及产率,污泥处理后溶解性化学需氧量、挥发性脂肪酸含量的变化和工程应用的优缺点,并指出目前研究存在的一些不足和对未来应用前景的展望,以期为剩余污泥发酵制氢预处理方法的研究与应用提供依据.     

Co-pyrolysis of oil sludge with hydrogen-rich plastics in a vertical stirring reactor: Kinetic analysis,emissions, and products

● Collaborative treatment of plastics and OS was established to improve oil quality. ● PE addition successfully improved OS pyrolysis process by deploying H/C_eff ratio. ● Higher H/C_eff ratio promoted cracking to obtain more gas and light oil fractions. ● The degradation of PE and OS was promoted each other under their temperature range. Pyrolysis is an effective method to treat oily sludge (OS) due to its balance between oil recovery and nonhazardous disposal. However, tank bottom OS contains a high content of heavy fractions, which creates obstacles for pyrolysis due to the high activation energy. The incomplete cracking of macromolecules and secondary polymerization decreases the oil quality and causes coking during the operation process. This study introduced polyethylene (PE) into OS to deploy the H/C_eff ratio of feedstocks for pyrolysis. A strong interaction between OS and PE during copyrolysis could be observed from the TG/DTG curves. PE tightly participated in OS degradation, while OS also promoted PE degradation at high temperature. Apparent pits were generated in solid residues from copyrolysis, which was attributed to the uniform and violent gas release. In addition to HCN, other nitrogenous and sulphurous pollutants were inhibited. Accordingly, more gas products were attained after PE addition with more value-added compositions of alkanes and alkenes. Although the oil yield decreased after PE addition, the oil products from copyrolysis possessed higher heating values and higher contents of light fractions with short chains as well as paraffins. Consequently, copyrolysis of OS and PE significantly improved the pyrolysis process and resulted in high oil quality.