Planar detonation structure for chain-branching kinetics with large activation energy and small initiation rate

The structure of the steady planar detonation wave is analyzed for three-step chain-branching kinetics consistent with hydrogen–air chemistry. The initiation and chain-branching steps are described by an Arrhenius rate. Both are thermally neutral, so that heat release is due to termination. The initiation rate is typically very low and very stiff. As a result, a small fraction of the reactant is consumed in the initiation region, which is very long but ends in an exponential chain-branching explosion. Next, the reactant is rapidly converted into chain-branching radicals, within a very thin zone, which ends when the concentration of the chain-branching radical reaches a peak, because of reactant depletion. Finally, the termination step consumes the chain-branching radicals and releases heat within a region thicker than the peak zone, but much thinner than the initiation region. The analysis is based upon two assumptions: that the chain-branching activation energy is high and that initiation is slow. The structure of the initiation and chain-branching zones is different for post-shock states within or outside the explosion region in the chain-branching diagram. In the former situation, chain-branching is already stronger than termination at the von Neumann point, and vice versa. In the no-explosion case, the initiation zone becomes very long, while the little chain-branching specie produced by initiation is directly converted into product by the termination step. Temperature increases slowly until reaching the explosion curve, when chain-branching becomes stronger than termination. The subsequent structure is similar to the explosion case.     

CONTROL OF LAKE PHOSPHORUS WITH ALUMINUM SULFATE: DOSE DETERMINATION AND APPLICATION TECHNIQUES1

ABSTRACT: Nutrient diversion does not always bring about prompt and sufficient reduction in lake phosphorus concentration due to recycling from nutrient rich sediments. Certain lakes and reservoirs may continue to experience nuisance algal blooms and require additional restorative steps. The phosphorus precipitation/inactivation technique is a procedure to remove phosphorus from the water column and to control its release from sediments in order to achieve P-limiting conditions to algal growth. Aluminum salts have been used in advanced waste water treatment to remove phosphorus and this technology was extended to lake rehabilitation. Guidelines for dose calculation and application are generally lacking, and are provided in this report. The dose determination suggested here allows maximum application of aluminum to bottom sediments and thus emphasizes long term control of phosphorus recycling. Dose can be calculated directly from the alkalinity of the water to be treated. Titration of lake water samples of Varying alkalinity allows the establishment of the relationship between residual dissolved aluminum, alkalinity, and dose which can then be employed for lake scale applications of alum to lakes and reservoirs. Application equipment and procedures are described. These depend on site characteristics and treatment objectives and include lakeside stores, a distribution pipe, and an application barge and manifold. Alum may also be used to meet other restoration objectives including the treatment of problem flows and the reduction of particulate concentrations.     

Development and Validation of the Total HUman Model for Safety (THUMS) Toward Further Understanding of Occupant Injury Mechanisms in Precrash and During Crash

Objective: Active safety devices such as automatic emergency brake (AEB) and precrash seat belt have the potential to accomplish further reduction in the number of the fatalities due to automotive accidents. However, their effectiveness should be investigated by more accurate estimations of their interaction with human bodies. Computational human body models are suitable for investigation, especially considering muscular tone effects on occupant motions and injury outcomes. However, the conventional modeling approaches such as multibody models and detailed finite element (FE) models have advantages and disadvantages in computational costs and injury predictions considering muscular tone effects. The objective of this study is to develop and validate a human body FE model with whole body muscles, which can be used for the detailed investigation of interaction between human bodies and vehicular structures including some safety devices precrash and during a crash with relatively low computational costs.

Methods: In this study, we developed a human body FE model called THUMS (Total HUman Model for Safety) with a body size of 50th percentile adult male (AM50) and a sitting posture. The model has anatomical structures of bones, ligaments, muscles, brain, and internal organs. The total number of elements is 281,260, which would realize relatively low computational costs. Deformable material models were assigned to all body parts. The muscle–tendon complexes were modeled by truss elements with Hill-type muscle material and seat belt elements with tension-only material. The THUMS was validated against 35 series of cadaver or volunteer test data on frontal, lateral, and rear impacts. Model validations for 15 series of cadaver test data associated with frontal impacts are presented in this article. The THUMS with a vehicle sled model was applied to investigate effects of muscle activations on occupant kinematics and injury outcomes in specific frontal impact situations with AEB.

Results and Conclusions: In the validations using 5 series of cadaver test data, force–time curves predicted by the THUMS were quantitatively evaluated using correlation and analysis (CORA), which showed good or acceptable agreement with cadaver test data in most cases. The investigation of muscular effects showed that muscle activation levels and timing had significant effects on occupant kinematics and injury outcomes. Although further studies on accident injury reconstruction are needed, the THUMS has the potential for predictions of occupant kinematics and injury outcomes considering muscular tone effects with relatively low computational costs.     

Rapid and simple spectrophotometric determination of persulfate in water by microwave assisted decolorization of Methylene Blue

A rapid and simple method for determination of persulfate in aqueous solution was developed. The method is based on the rapid reaction of persulfate with Methylene Blue(MB) via domestic microwave activation, which can promote the activation of persulfate and decolorize MB quickly. The depletion of MB at 644 nm(the maximum absorption wavelength of MB) is in proportion to the increasing concentration of persulfate in aqueous solution. Linear calibration curve was obtained in the range 0–1.5 mmol/L, with a limit of detection of 0.0028 mmol/L. The reaction time is rapid(within 60 sec), which is much shorter than that used for conventional methods. Compared with existing analytical methods, it need not any additives, especially colorful Fe2+, and need not any pretreatment for samples, such as p H adjustment.     

不同磁黄铁矿自养反硝化脱氮除磷作用

氮磷排放标准日趋严格,开发高效廉价脱氮除磷材料已成为研究热点.采用黄铁矿与赤铁矿在管式炉中氮气气氛下600 ℃煅烧,得到硫化赤铁矿形成的磁黄铁矿、黄铁矿热分解形成的磁黄铁矿,构建磁黄铁矿-方解石体系处理含氮磷模拟废水,对比不同方式制备的磁黄铁矿、天然磁黄铁矿、黄铁矿、硫磺脱氮除磷性能,考察不同磁黄铁矿晶体结构和结晶度差异及其对脱氮除磷影响,探究不同体系中矿物结构和微生物群落变化.结果表明：黄铁矿热分解产物以六方磁黄铁矿为主;硫化赤铁矿产物以低结晶度的单斜磁黄铁矿为主,因而表现出优异的脱氮除磷活性,氮磷去除率分别为99.8%和96.8%.铁硫化物与微生物反应产物的XRD、SEM和FE-TEM分析结果表明,微生物能有效利用磁黄铁矿进行脱氮,磷酸盐主要以FePO₄形式被去除.群落分析结果表明铁硫化物脱氮除磷体系中的主要功能菌属为Thiobacillus和 Sulfurimonas,结晶度低的单斜磁黄铁矿更有利于Thiobacillus定向富集.     

Hydrothermal-treated Pt/Al2O3 as an excellent catalyst for toluene total oxidation

The preparation of highly active supported noble metal catalysts with a low noble metal loading has always been the ultimate goal of researchers working on catalysis. Hydrothermally treated Pt/Al₂O₃ (Pt/Al₂O₃-H) exhibits better catalytic activity than that (Pt/Al₂O₃-C) treated via the conventional calcination approach. At the high space velocity of 100,000 mL/(g∙hr), the temperature that correspond to 50% toluene conversion (T₅₀) of Pt/Al₂O₃-H is 115°C lower than that of Pt/Al₂O₃-C, and the turnover frequency (TOF) value can reach 0.0756 sec⁻¹. The mechanism by which the hydrothermal approach enhances Pt/Al₂O₃ activity has been investigated. The structure associated with the high catalytic activity of Pt nanoparticles (NPs) can be retained via hydrothermal treatment. Furthermore, the support is transformed to AlO(OH) with numerous surface hydroxyl groups, which in turn can facilitate the adsorption of toluene. And the synergistic effects of Pt NPs and AlO(OH) increases the contents of Pt in oxidation state and active oxygen, which are beneficial for toluene oxidation.     

Phenol degradation in waters with high iodide level by layered double hydroxide-peroxodisulfate: Pathways and products

Recently, layered double hydroxide-peroxodisulfate (LDH-PDS) as an advanced oxidation system can effectively remove organics by the pathway of free radical. However, little has been known if there is a potential risk regarding the formation of high toxic iodine byproducts through another pathway when LDH-PDS is used in high iodide waters at coastal areas. Therefore, this study investigated phenol degradation pathways and transformation products to evaluate both removal mechanism and potential risk by LDH-PDS in high iodide waters. The results showed that in LDH-PDS system, with the degradation of PDS, phenol degraded till below detection limit in 1 hr in the presence of iodide, while PDS and phenol were hardly degraded in the absence of iodide, indicating iodide accelerated the transformation of PDS and the degradation of phenol. What is more, it reached the highest phenol removal efficiency under the condition of 100 mg/L LDH, 0.1 mmol/L PDS and 1.0 mmol/L iodide. In LDH-PDS system, iodide was rapidly oxidized by the highly active interlayer PDS, resulting in the formation of reactive iodine including hypoiodic acid, iodine and triiodide instead of free radicals, which contributed rapid degradation of phenol. However, unfortunately toxic iodophenols were detected. Specifically, 2-iodophenol and 4-iodophenol were formed firstly, afterwards 2,4-diiodophenol and 2,6-diiodophenol were produced, and finally iodophenols and diiodophenols gradually decreased and 2,4,6-Triiodophenol were produced. These results indicated that LDH-PDS should avoid to use in high iodide waters to prevent toxic iodine byproduct formation although iodide can accelerate phenol degradation.     

铝及铝合金在自然水环境中的腐蚀行为对比研究

目的 分析研究铝及铝合金在自然水环境中的腐蚀行为。方法 通过开展LM3纯铝、5083铝、LF6M去包铝及带包铝在淡海水交替、海水及淡水自然环境下2 a的暴露试验,将3种环境下材料的腐蚀形貌、腐蚀速率进行对比。总结4种铝及铝合金材料在不同水环境下的腐蚀规律,对其腐蚀机理进行简要的探讨,并对其长周期的腐蚀行为进行预测。结果 通过对4种材料局部腐蚀协同影响因子(b)的对比可以发现,淡水环境对LM3纯铝局部腐蚀的影响最大,淡海水环境对5083铝合金局部腐蚀影响最大,淡水及淡海水环境对2种LF6M铝合金材料局部腐蚀的影响都很大。结论 5083、LF6M带包铝及去包铝,在淡海水交替自然环境下的耐蚀性能最差,LM3纯铝在淡水环境下耐蚀性能最差。     

KOH活化小麦秸秆生物炭对废水中四环素的高效去除

活化是提高生物炭吸附性能的重要手段.以小麦秸秆为研究对象,KOH为活化剂,制备KOH活化生物炭（K-BC）,同时制备原状生物炭（BC）作为对照.对生物炭进行比表面积和孔径、元素分析、XPS、FTIR、Raman、XRD和pH_pzc等表征,考察KOH活化对生物炭理化性质的影响,并探究生物炭对水体中四环素的吸附性能和机制.结果表明,KOH活化之后生物炭的比表面积和孔体积可达996.4 m²·g^-1和0.45 cm³·g^-1.KOH活化会制造更多的碳结构缺陷,影响生物炭的官能团和表面电性.拟二级动力学和Langmuir模型可以较好地拟合生物炭吸附四环素的过程.环境温度升高能提高生物炭对四环素的吸附量.K-BC吸附四环素是自发、吸热和无序度增加的过程.K-BC对四环素的最大吸附量理论可达到491.19 mg·g^-1（实验温度为45℃）.结合吸附后生物炭的Raman、FTIR和XPS表征,发现孔隙填充和π-π作用是K-BC吸附四环素的主要机制,氢键和络合作用也发挥重要作用.此外,K-BC还具有良好的循环使用性能.综上所述,KOH活化小麦秸秆生物炭是有效和可行的,可用于废水中四环素的去除.     

Heavy metal bioaccumulation in selected medicinal plants collected from Khetri copper mines and comparison with those collected from fertile soil in Haridwar,India

Heavy metal distribution in medicinal plants is gaining importance not only as an alternative medicine, but also for possible concern due to effects of metal toxicity. The present study has been focused on emphasizing the heavy metal status and bioaccumulation factors of V, Mn, Fe, Co, Cu, Zn, Se (essential metals) and Cr, Ni, Cd, As and Pb (potentially toxic metals) in medicinal plants grown under two different environmental conditions e.g., near to Khetri copper mine and those in fertile soils of Haridwar, both in India, using Instrumental Neutron Activation Analysis (relative method) and Atomic Absorption Spectrometry. The copper levels in the medicinal plants from Khetri were found to be 3-4 folds higher (31.6–76.5 mg kg^?1) than those from Haridwar samples (7.40–15.3 mg kg^?1), which is correlated with very high copper levels (763 mg kg^?1) in Khetri soil. Among various heavy metals, Cr (2.60–5.92 mg kg^?1), Cd (1.47–2.97 mg kg^?1) and Pb (3.97–6.63 mg kg^?1) are also higher in concentration in the medicinal plants from Khetri. The essential metals like Mn (36.4–69.3 mg kg^?1), Fe (192–601 mg kg^?1), Zn (24.9–49.9 mg kg^?1) and Se (0.13–0.91 mg kg^?1) and potentially toxic metals like Ni (3.09–9.01 mg kg^?1) and As (0.41–2.09 mg kg^?1) did not show much variations in concentration in the medicinal plants from both Khetri and Haridwar. The medicinal plants from Khetri, e.g., Ocimum sanctum, Cassia fistula, Withania somnifera and Azadirachta Indica were found rich in Ca and Mg contents while Aloe barbadensis showed moderately high Ca and Mg. Higher levels of Ca-Mg were found to correlate with Zn (except Azadirachta Indica). The bioaccumulation factors (BAFS) of the heavy metals were estimated to understand the soil-to-plant transfer pattern of the heavy metals. Significantly lower BAF values of Cu and Cr were found in the medicinal plants from Khetri, indicating majority fraction of these metals are precipitated and were immobilized species unsuitable for plant uptake. Overall, Withania somnifera (Ashwagandha) showed very high metal bioaccumulation.