摩托车防护服装设计方法研究

本课题在摩托车防护服装设计因素分析的基础上,对摩托车防护服装的设计方法进行了系统研究,探讨了能够实现安全防护性能和舒适性能的摩托车防护服的设计方法。通过系统完整的设计过程,设计人员能够形成一个正确的设计理念和体系化的设计步骤。     

化学防护服的分类及选用

本文较为系统地介绍了化学防护服的分类方法、典型化学防护服的特点和适用场合及化学防护服选择应考虑的主要因素和一般程序,对化学防护服的选用具有一定的指导意义。     

淋雨及不同温度条件对消防员防护服各部位热阻的影响

为了研究淋雨及不同温度条件对消防员防护服各部位热阻的影响,以消防防护服为研究对象,利用环境舱和暖体假人系统,在20 mm/h降雨强度和20~30 ℃的复合环境条件下,研究淋雨、不同温度复合环境对服装各部位热阻的影响。研究结果表明:淋雨过程中,服装热阻的变化趋势为先上升再下降最后趋于稳定;淋雨与不同温度复合环境会使得消防防护服热阻降低,其中影响较大的部位为上臂部、腹部、胸部、背部及臀部等。     

环境温度对化学防护服气密性能影响研究

为研究不同温度条件对化学防护服（CPC）气密性的影响,以3种不同材质（聚乙烯、丙烯、氯化丁基橡胶）的化学防护服为研究对象,利用气密性测试仪和环境实验舱,在10~66 ℃温度条件下处理2 h后,分析环境温度对3种化学防护服样品气密性能影响。研究结果表明:不同环境工况处理后化学防护服气密性能在10~25 ℃段上升,在25~50 ℃段下降;聚乙烯材质化学防护服失效温度为66 ℃,其他2种材质的服装失效温度为50 ℃。研究可为防护装备环境适应性测试评价提供技术支撑。     

低温作业对人体的危害及防寒工作服的性能评价

防寒工作服是冬季保护石油行业室外作业人员的重要措施。文章阐述了低温环境对石油行业室外作业人员身体健康的影响,列举了防寒工作服生产和检测的重要性能参数和测定方法,概括了国内外对于防寒工作服生产和检测的相关标准,展望了防寒工作服研发应用空间和发展方向,对防寒工作服的研究和配备有一定的参考价值。     

Penetration of soil dust through woven and nonwoven fabrics

Abstract

Several types of fabrics were laboratory‐tested for their effectiveness in worker protection to pesticide‐laden dust encountered in the agricultural environment. Of the applied <100 mesh dust, penetrations through knitted jersey and woven fabrics were greater than 87% and less than 5.8%, respectively. Treatment of woven fabrics with fluorocarbon polymers curtailed penetration by greater than 60%. Nonwoven fabrics allowed less than 0.5% dust penetration. Parathion mixed with 100‐mesh sieved dust resulted in increasing “ppm”; levels with decreasing particle size; extent of parathion conversion to paraoxon was independent of particle size for the sandy loam dust used.     

Parallel and Serial Methods of Calculating Thermal Insulation in European Manikin Standards

Abstract

Standard No. EN 15831:2004 provides 2 methods of calculating insulation: parallel and serial. The parallel method is similar to the global one defined in Standard No. ISO 9920:2007. Standards No. EN 342:2004, EN 14058:2004 and EN 13537:2002 refer to the methods defined in Standard No. EN ISO 15831:2004 for testing cold protective clothing or equipment. However, it is necessary to consider several issues, e.g., referring to measuring human subjects, when using the serial method. With one zone, there is no serial-parallel issue as the results are the same, while more zones increase the difference in insulation value between the methods. If insulation is evenly distributed, differences between the serial and parallel method are relatively small and proportional. However, with more insulation layers overlapping in heavy cold protective ensembles, the serial method produces higher insulation values than the parallel one and human studies. Therefore, the parallel method is recommended for standard testing.     

Thermal Strain in Fire Fighters While Wearing Task-Fitted Versus EN 469:2005 Protective Clothing During a Prolonged Rescue Drill

Fire fighters are normally overprotected during their working hours because of the tendency to keep the personal protection level sufficiently high in case of the worst possible scenarios. This study investigated the effects of task-fitted protective clothing on thermal strain in fire fighters as compared to EN 469:2005 protective clothing during a prolonged (2 1/2 hrs) job-related rescue drill under neutral and hot climates. The subjects were 23 healthy, physically fit professional male fire fighters aged 26–44 years. Measurements included cardiovascular and thermal responses and subjective assessments. Wearing task-fitted clothing during rescue tasks in a neutral climate considerably reduced total thermal and cardiovascular strain in prolonged rescue work. The fire fighters also perceived physical work as significantly harder on average, and reported more intense subjective discomfort while wearing EN 469:2005 as compared to task-fitted clothing.     

建筑行业职业工装的应用设计

本文通过对建筑行业工作特点及其安全性的要求分析,研究建筑行业职业工装的款式结构、服装安全色彩的选择以及服装加工过程中的规范,对建筑行业职业工装提出了具体的设计方法,总结出了较系统的思路,以期为建筑行业安全生产提供必要的保障。     

气凝胶消防服概念研究

对现役消防服的隔热材质和使用性能,以及气凝胶作为新型纳米隔热材料在服装方面的应用现状进行了分析。根据初步对比讨论了SiO2气凝胶复合材料用于消防服的可行性,得出以下结论：在同样的热防护性能前提下,采用SiO2气凝胶复合材料可使消防服重量及厚度降低70％以上。