锐钛矿-金红石混合晶型TiO2降解气相苯

用溶胶-凝胶法并通过控制煅烧温度合成不同晶相比的混合晶型纳米TiO_2,在紫外光光照下降解气相苯。考察了苯初始质量浓度、紫外灯光照强度和催化剂加入量对苯去除率的影响;探究了光催化降解气相苯的动力学特征。结果表明:450℃煅烧制备的催化剂降解苯效率最高,此催化剂金红石相质量分数为6.30%;在苯初始质量浓度为74.39 mg/m~3、催化剂加入量为7 g、光照强度为2.18 klux的最佳条件下反应84 min,苯去除率达99.73%;光催化降解率与光照强度之间符合0.5级动力学特征;当催化剂加入量为3 g时,单位时间单位质量催化剂降解苯的质量最多;苯的光催化降解反应均符合一级动力学方程。     

壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B动力学研究

采用仿生矿化法制备了壳聚糖/纳米CdS复合颗粒光催化剂,并用于可见光光催化降解猩红B染料模拟废水,研究了猩红B初始浓度、pH、催化剂投加量和催化剂重复使用次数等因素对猩红B光催化降解的影响.X射线衍射(XRD)分析表明,壳聚糖能有效负载CdS纳米微晶.采用Langmuir-Hinshelwood模型描述壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B反应动力学行为,在猩红B初始质量浓度较低(≤20 mg/L)时,光催化降解过程符合假一级动力学方程.降低猩红B初始浓度和溶液pH都可显著增大光催化降解速率常数;催化剂投加量小于0.7 g/L时,光催化降解速率随其增加而增大,但催化剂投加量过大会使光催化降解速率减小;催化剂重复使用第5次时,猩红B光催化降解速率常数仍为第1次使用时的63.4%.     

高锰酸钾降解地下水中PCE的研究

以氯代有机污染物中常见的PCE为目标污染物,以自制高锰酸钾溶液为氧化剂,采用批实验方法,探讨了高锰酸钾降解PCE的反应动力学、影响因素以及反应机理。反应结果表明,高锰酸钾降解PCE的反应符合一级动力学方程,反应活化能E为57.119 kJ/mol,在30℃条件下,反应速率常数为0.0076 min^-1,半衰期为91.20 min。在pH在3～10,离子强度在0～0.1030 mol/L之间变化时,反应速率不受明显影响。     

Detection of Class I and II integrons for the assessment of antibiotic and multidrug resistance among Escherichia coli isolates from agricultural irrigation waters in Bulacan,Philippines

Contaminated irrigation water may greatly affect not only the quality of produce but also the people exposed to it. In this study, agricultural irrigation waters in Bulacan, Philippines were assessed and found to be contaminated with Escherichia coli (E. coli) ranging from 0.58 to 4.51 log₁₀ CFU/mL. A total of 79 isolates of E. coli were confirmed through polymerase chain reaction (PCR) amplifying the uidA gene and were tested for phenotypic resistance using 10 antimicrobials through the Kirby–Bauer disc diffusion method. Forty-six isolates (58.22%) were noted to be multidrug resistant (MDR) with high resistance rate to cephalothin, tetracycline, streptomycin, ampicillin, trimethoprim, nalidixic acid, and chloramphenicol. Moreover, this study also examined the prevalence of Class I and II integrons accounting to 67.39% and 17.39%, respectively, of the MDR E. coli strains using multiplex PCR. The results imply that the agricultural water used in Bulacan is contaminated with the fecal material of man or other animals present in the area, and the presence of MDR bacteria, which pose a potential threat to individuals in these areas, is alarming. In addition, detection of integrons could be a good marker for the identification of MDR isolates. Lastly, this study could develop strategies for the proper management of farming sites leading to the detection of food-borne pathogens and prevention of infectious diseases.     

Photolysis of the herbicide bispyribac sodium in aqueous medium under the influence of UV and sunlight in presence or absence of sensitizers

The photolysis of a rice herbicide Bispyribac sodium (Sodium 2, 6-bis [(4, 6-dimethoxypyrimidin-2-yl) oxy] benzoate) has been studied in different aqueous medium (distilled water, pond water and Irrigation water) under the influence of UV (λ max ≥ 250 nm) and sunlight in presence or absence of sensitizers (TiO₂ and KNO₃). The study was conducted under laboratory simulated condition which made it possible to evaluate the contribution of different factors viz. source of irradiation, solvent and sensitizers towards the photolysis of bispyribac sodium. The photodegradation proceeds via first order reaction Kinetics in all the cases. Five photo metabolites (M₁-M₅) were isolated in pure form by column chromatographic method from the irradiation system under UV influenced and TiO₂ as sensitizer. From the different spectral data (IR, NMR, UV-VIS, Mass) the structure of these five metabolites were assigned as M₁ (Phenol), M₂ [2, 6-Dihydroxy benzoic acid], M₃ [2, 6-bis [(4, 6 dimethoxypyrimidin-2yl) oxy] benzoic acid], M₄ [2-(3-Hydroxy-phenoxy)-pyrimidine-4, 6-diol] and M₅ as [2,4-Dihydroxy-3, 5-dimethoxy-6-(4-methoxy pyrimidine-2-yloxy)-benzoic acid]. Moreover, another six photometabolites (M₆-M₁₁) were identified from the different irradiation system on the basis of Micromass analysis. On the basis of MS/MS data analysis, the structure of these six photometabolites were assigned as M₆ [2-(4, 6-Dimethoxy-pyrimidin-2-yloxy)-6-hydroxy-benzoic acid], M₇ [2-Hydroxy-6-(4-hydroxy-6-methoxy-pyrimidin-2-yloxy)-benzoic acid], M₈ [4, 6-Dimethoxy-pyrimidin-2-ol], M₉ [6-Methoxy-pyrimidine-2, 4-diol], M₁₀ [2-Hydroxy-6-(pyrimidin-2-yloxy)-benzoic acid] and M₁₁ [2, 4, 6-Trimethoxy-pyrimidine]. The plausible Photodegradation pathways of bispyribac sodium in the present investigation were portrayed which proceeds via hydrolysis, hydrolytic cleavage, O-dealkylation, decarboxylation, dehydroxylation, O-alkylation and hydroxylation.     

过硫酸钾去除水中的TCE

以地水中的氯代烃污染物三氯乙烯(TCE)为目标污染物,以过硫酸钾溶液为氧化剂,探讨了不同条件下过硫酸钾对TCE的去除效果。实验结果表明,在40℃,过硫酸钾初始浓度为2.43 g/L条件下,反应2 h后,TCE的去除率就可达到96.8%;过硫酸钾对TCE的去除符合一级反应动力学方程,速率常数(K)为1.3364 h-1,半衰期(t1/2)为0.51 h;过硫酸钾对TCE的去除速率在pH为中性附近时最大,其后无论pH升高或降低去除速率均减小;受温度和pH影响较明显,并且反应温度越高,受pH的影响越明显;随离子强度的增加而减小;反应活化能为119.6 kJ/mol;过硫酸钾溶于水生成过硫酸根离子(S2O28-),S2O28-会进一步生成硫酸根自由基(SO4-.),在碱性条件下,SO4-.与OH-反应会进一步生成羟基自由基(.OH)。过硫酸钾对于TCE的去除主要源自SO4-.和.OH的强氧化性。     

稠油污水回用锅炉处理工艺的应用

新疆油田公司稠油污水处理普遍采用成熟的离子调整旋流反应水处理技术,污水处理后达到回用锅炉水质标准SY/T 0097-2000《稠油油田采出水用于蒸汽发生器给水处理设计规范》,供给油田专用高压注汽锅炉用水。采用相同技术建成的采油一厂稠油处理站污水回用锅炉处理工艺投用后,处理后污水回用锅炉,减少了含油污水的外排,充分利用了稠油污水的热能,取得了良好的经济和社会效益。     

Desorption of polycyclic aromatic hydrocarbons from field-contaminated soil to a two-dimensional hydrophobic surface before and after bioremediation

This study investigated environmental distributions and production mechanisms of chlorinated polycyclic aromatic hydrocarbons (Cl-PAHs) in the sediments from some tidal flats located in Asia. Cl-PAHs were found in sediments taken from Arao tidal flat, Kikuchigawa River and Shirakawa River. The range of ∑Cl-PAHs was from 25.5 to 483 pg g⁻¹ for Kikuchigawa River and Arao tidal flat, respectively.Concentrations of PAHs and Cl-PAHs showed no significant correlations (r = 0.134). This result suggests that the origins of these compounds differ. In the identified Cl-PAH isomers, the most abundant Cl-PAH isomer was 9,10-dichloroanthracene (9,10-di-Cl-ANT) in the three sites. In general, concentrations of Cl-ANTs in the coastal environment are about 3-5 orders of magnitude lower than those of anthracene (ANT). However, concentration ratios between Cl-ANTs and ANT (Cl-ANTs/ANT) in the sediments ranged from 4.1% to 24.6%. This result indicated that Cl-PAHs were not generated under industrial processes but the high concentration ratios have resulted from the contribution of photochemical production of Cl-ANTs in the sediments because ANT is known to have high photochemical reactivity.For examining this phenomenon, ANT adsorbed onto glass beads was irradiated with UV under the mimicked field conditions of tidal flats. As a result, it was noticed that, while chlorinated derivatives were negligible in a light-controlled group, production of 2-Cl-ANT, 9-Cl-ANT and 9,10-diCl-ANT on the irradiated surface were found in this study. These results suggest that photochemical reaction of PAHs can be a potential source of the occurrence of Cl-PAHs in the coastal environment.     

The structure of the fire fighting foam surfactant Forafac®1157 and its biological and photolytic transformation products

For several decades, perfluorooctane sulfonate (PFOS) has widely been used as a fluorinated surfactant in aqueous film forming foams used as hydrocarbon fuel fire extinguishers. Due to concerns regarding its environmental persistence and toxicological effects, PFOS has recently been replaced by novel fluorinated surfactants such as Forafac®1157, developed by the DuPont company. The major component of Forafac®1157 is a 6:2 fluorotelomer sulfonamide alkylbetaine (6:2 FTAB), and a link between the trade name and the exact chemical structure is presented here to the scientific community for the first time. In the present work, the structure of the 6:2 FTAB was elucidated by ¹H, ¹³C and ¹⁹F nuclear magnetic resonance spectroscopy and high-resolution mass spectrometry. Moreover, its major metabolites from blue mussel (Mytilus edulis) and turbot (Scophthalmus maximus) and its photolytic transformation products were identified. Contrary to what has earlier been observed for PFOS, the 6:2 FTAB was extensively metabolized by blue mussel and turbot exposed to Forafac®1157. The major metabolite was a deacetylated betaine species, from which mono- and di-demethylated metabolites also were formed. Another abundant metabolite was the 6:2 fluorotelomer sulfonamide. In another experiment, Forafac®1157 was subjected to UV-light induced photolysis. The experimental conditions aimed to simulate Arctic conditions and the deacetylated species was again the primary transformation product of 6:2 FTAB. A 6:2 fluorotelomer sulfonamide was also formed along with a non-identified transformation product. The environmental presence of most of the metabolites and transformation products was qualitatively demonstrated by analysis of soil samples taken in close proximity to an airport fire training facility.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni(NO3)2和Fe(NO3)3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO+NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。