Thermal and mechanical properties of poly(lactic Acid) and poly(ethylene/butylene Succinate) blends

In this study, blends of poly (lactic acid) (PLA) with poly(ethylene/butylene succinate) (Bionolle) have been investigated for their thermal and mechanical properties as a function of the concentration of Bionolle. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and tensile tests were used to characterize the blends. From the results of the DMA and DSC, it was found that this blend system was not miscible within the compositions studied. DSC results showed that adding Bionolle aids in crystallization of PLA. It was observed that increasing the Bionolle concentration led to a slight increase in the strain-at-break of the blends but a decrease in the Young’s modulus and ultimate tensile strength. Biaxially oriented films showed an increase in tensile strength, modulus, and strain-at-break.     

Synthesis of poly(hydroxyalkanoate) from hydrolyzed linseed oil

Pseudomonas putida was grown on a mixture of long-chain fatty acids obtained by hydrolysis of linseed oil. A poly(3-hydroxyalkanoate) containing 51.2% of unsaturated monomers was obtained. A considerable percentage (13.6%) was constituted by C₁₄ and C₁₆ monomers containing three double-bonds in the side chains. The polymer showed a high tendency to crosslink when it was kept in presence of air. In the crosslinked polymer no polyunsaturated monomers could be detected.     

仪化热电厂提高循环水浓缩倍率的措施

针对仪化热电厂将循环水用作冲灰水，导致浓缩倍率只有1.6，以及凝汽器铜管腐蚀结垢严重等问题，提出了隔断循环水与冲灰水的直接联系，实现闲路循环，对凝汽器铜管进行酸洗，并对循环水实施加缓蚀阻垢荆、杀菌剂和旁流过滤等办法，全部实施后产生了很好的效益，值得借鉴。     

Mechanical and Barrier Properties of Biodegradable Films Made from Chitosan and Poly (Lactic Acid) Blends

Biodegradable film blends of chitosan with poly(lactic acid) (PLA) were prepared by solution mixing and film casting. The main goal of these blends is to improve the water vapor barrier of chitosan by blending it with a hydrophobic biodegradable polymer from renewable resources. Mechanical properties of obtained films were assessed by tensile test. Thermal properties, water barrier properties, and water sensitivity were studied by differential scanning calorimeter analysis, water vapor permeability measurements, and surface-angle contact tests, respectively. The incorporation of PLA to chitosan improved the water barrier properties and decreased the water sensitivity of chitosan film. However, the tensile strength and elastic modulus of chitosan decreased with the addition of PLA. Mechanical and thermal properties revealed that chitosan and PLA blends are incompatible, consistent with the results of Fourier transform infrared (FTIR) analysis that showed the absence of specific interaction between chitosan and PLA.     

金沙江对硫酸的缓冲性能分析

本文分析了金沙江对硫酸的缓冲特征，建立了江水的缓冲曲线方程，并且验证了此方程的有效性，证明用此方程预测硫酸进入金沙江后江水pH值的变化情况，其预测准确度在0.2个pH单位内。     

树脂相分光光度法测定水中痕量苦味酸

建立了树脂相分光光度法测定水中痕量苦味酸的新方法。该法灵敏度高,表观摩尔吸光系数为1.08×105L/(mol·cm);精密度理想(测定苦味酸质量浓度为5μg/mL的实验5次,相对标准偏差为1.0%);线性范围为0～7.0μg/mL;以3σ衡量,检出限为0.14μg/mL;加标回收率为97%～103%。采用该法直接测定水样中的苦味酸、间接测定烟草中的烟碱,结果令人满意。     

硅胶管吸附气相色谱法测定气体中的乙酸、丙酸

建立了用GC-FID同时测定空气中乙酸、丙酸的方法.乙酸、丙酸经硅胶管吸附后,用丙酮溶剂解吸,气相色谱分析.优化条件下,在20 ～2 000 mg/L范围内有良好的线性关系.方法检出限分别达到了1.0 mg/m3和0.5 mg/m3,相对标准偏差2.2％和1.9％,回收率在94％以上.     

浙江省酸雨的空间分布格局及其未来变化趋势预测

利用浙江省1992、2002年的酸雨监测数据,并利用RAINS-ASIA模型模拟了1990-2030年浙江省酸雨前体物(SO2)的排放量,以及酸沉降超临界负荷面积占研究区域面积比例的变化情况.结果表明,浙江省的酸雨分布范围不断扩大、危害程度不断加重;未来一个时期内,SO2排放量都会维持在较高的水平;酸沉降超临界负荷面积所占比例在经历较快的增长阶段之后,会维持在较为恒定的水平,并呈现出明显的时滞性.     

活性粉末混凝土的耐酸性

为了考察活性粉末混凝土在严酷环境下的耐酸性能,试验研究了硫酸溶液和醋酸溶液对活性粉末混凝土强度的影响,并比较研究了硫酸溶液对普通水泥基材料和高强水泥基材料的影响。70d浸泡龄期的试验结果表明:在浸泡早期,3种水泥基材料的耐硫酸性能差别不明显,随着暴露时间的延长,活性粉末混凝土比普通水泥基材料和高强水泥基材料呈现出较好的耐硫酸性能;弱离解的醋酸溶液对活性粉末混凝土的侵蚀作用比强离解的硫酸溶液更强。前者与3种水泥基材料的孔隙率、孔隙结构、抗渗性及抗裂性等因素有关,后者则与醋酸溶液的强扩散性有关。