陆浑水库沉积物重金属空间分布特征及风险评价

为了解洛阳市饮用水水源地陆浑水库沉积物中重金属污染程度,采集32个点位的表层沉积物,分析6种重金属（Cd、Cr、Cu、Ni、Pb和Zn）的空间分布特征,并运用地累积指数法、潜在生态风险指数和聚类分析等方法对研究区重金属污染程度进行评价、生态风险评价及源解析.结果表明：Cd、Cu、Pb和Zn含量超过黄河流域河南段重金属土壤背景值,分别是其8.8、2.0、6.5、2.3倍,重金属存在明显富集,且主要污染集中于坝前区域.地累积指数法评价结果显示,Cd为强污染,Pb为中-强污染.潜在生态风险指数表明,陆浑水库沉积物重金属风险呈自上游至下游逐渐增强的趋势,总体处于高度生态危害,潜在生态风险指数均值达到312.94,其中Cd为主要贡献因子.富集系数法和聚类分析结果显示：Cd、Cu、Pb和Zn主要为人为源,Cr和Pb以自然源为主.总体而言,陆浑水库沉积物中重金属Cd和Pb污染相对较重,可能会对水库水环境构成威胁.     

固定源可凝结颗粒物稀释采样器的设计

固定污染源烟气排放进入大气环境后稀释降温,气相中部分饱和蒸气压较低的组分转化为可凝结颗粒物,这部分颗粒物在固定源烟气颗粒物监测中通常被忽略.为评价固定源可凝结颗粒物的排放情况,本文设计开发并评测了一套稀释采样器.稀释采样器稀释比在10：1~40：1范围内,混合停留时间为5~10 s.实验室评测结果表明,稀释气颗粒物背景值低（（~0.1±0.08） 个·cm^-3）,稀释采样器气密性良好,烟气和稀释气能够均匀混合,颗粒物损失较少,细颗粒物 （PM_2.5）损失在5%以下.本稀释采样器能模拟烟气与环境空气混合降温过程,可用于固定源可凝结颗粒物的测量.     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.     

苯醌对聚合硅酸铁多相UV-Fenton体系的增效机制

通过构建苯醌增效聚合硅酸铁多相UV-Fenton体系,讨论了体系中橙Ⅱ的脱色和降解途径.在研究苯醌浓度对聚合硅酸铁铁离子的释放、Fe²⁺与Fe³⁺之间的转化、H₂O₂分解和·OH生成影响的基础上,提出了苯醌对聚合硅酸铁多相UV-Fenton体系的增效机制.结果表明,随苯醌浓度的增加,其紫外光下光解还原聚合硅酸铁并释放Fe²⁺的程度增大、H₂O₂分解速度加快、产生·OH浓度峰值增高且出现的时间提前;苯醌增效体系释放于溶液中的Fe²⁺可以通过Fenton反应转化成Fe³⁺,反应结束后聚合硅酸铁能重新吸附Fe³⁺并使其浓度降低,避免了增效体系铁离子的二次污染.本研究将为多相催化剂催化过程的调控提供新的视角,为多相光助-芬顿反应在有机废水资源化中的应用提供理论依据和技术支持.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Revealing the changes of bacterial community from water source to consumers tap: A full-scale investigation in eastern city of China

This study profiled the bacterial community variations of water from four water treatment systems, including coagulation, sedimentation, sand filtration, ozonation-biological activated carbon filtration (O₃-BAC), disinfection, and the tap water after the distribution process in eastern China. The results showed that different water treatment processes affected the bacterial community structure in different ways. The traditional treatment processes, including coagulation, sedimentation and sand filtration, reduced the total bacterial count, while they had little effect on the bacterial community structure in the treated water (before disinfection). Compared to the traditional treatment process, O₃-BAC reduced the relative abundance of Sphingomonas in the finished water. In addition, ozonation may play a role in reducing the relative abundance of Mycobacterium. NaClO and ClO₂ had different effects on the bacterial community in the finished water. The relative abundance of some bacteria (e.g. Flavobacterium, Phreatobacter and Porphyrobacter) increased in the finished water after ClO₂ disinfection. The relative abundance of Mycobacterium and Legionella, which have been widely reported as waterborne opportunistic pathogens, increased after NaClO disinfection. In addition, some microorganisms proliferated and grew in the distribution system, which could lead to turbidity increases in the tap water. Compared to those in the finished water, the relative abundance of Sphingomonas, Hyphomicrobium, Phreatobacter, Rheinheimera, Pseudomonas and Acinetobacter increased in the tap water disinfected with NaClO, while the relative abundance of Mycobacterium increased in the tap water disinfected with ClO₂. Overall, this study provided the detailed variation in the bacterial community in the drinking water system.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

On-going nitrification in chloraminated drinking water distribution system (DWDS) is conditioned by hydraulics and disinfection strategies

Within the drinking water distribution system (DWDS) using chloramine as disinfectant, nitrification caused by nitrifying bacteria is increasingly becoming a concern as it poses a great challenge for maintaining water quality. To investigate efficient control strategies, operational conditions including hydraulic regimes and disinfectant scenarios were controlled within a flow cell experimental facility. Two test phases were conducted to investigate the effects on the extent of nitrification of three flow rates (Q = 2, 6, and 10 L/min) and four disinfection scenarios (total Cl₂=1 mg/L, Cl₂/NH₃-N=3:1; total Cl₂=1 mg/L, Cl₂/NH₃-N=5:1; total Cl₂=5 mg/L, Cl₂/NH₃-N=3:1; and total Cl₂=5 mg/L, Cl₂/NH₃-N=5:1). Physico-chemical parameters and nitrification indicators were monitored during the tests. The characteristics of biofilm extracellular polymetric substance (EPS) were evaluated after the experiment. The main results from the study indicate that nitrification is affected by hydraulic conditions and the process tends to be severe when the fluid flow transforms from laminar to turbulent (2300<Re<4000). Increasing disinfectant concentration and optimizing Cl₂/NH₃-N mass ratio were found to inhibit nitrification to some extend when the system was running at turbulent condition (Q = 10 L/min, Re = 5535). EPS extracted from biofilm that was established at the flow rate of 6 L/min had greater carbohydrate/protein ratio. Furthermore, several nitrification indicators were evaluated for their prediction efficiency and the results suggest that the change of nitrite, together with total organic carbon (TOC) and turbidity can indicate nitrification potential efficiently.     

Sources, distribution, and risk assessment of organochlorine pesticides in Nairobi City, Kenya

The distribution and sources of organochlorine pesticides (OCPs) in air and surface waters were monitored in Nairobi City using triolein-filled semipermeable membrane devices (SPMDs). The SPMDs were extracted by dialysis using n-hexane, followed by cleanup by adsorption chromatography on silica gel cartridges. Sample analysis was done by GC-ECD and confirmed by GC–MS. Separation of means was achieved by analysis of variance, followed by pair-wise comparison using the t-test (p≤ 0.05). The total OCPs ranged between 0.018 – 1.277 ng/m³ in the air and <LOD – 1391.000 ng/m³ in surface waters. Based on the results, the means of Industrial Area, Dandora and Kibera were not significantly different (p≤ 0.05), but were higher (p≤ 0.05) than those of City square and Ngong’ Forest. The results revealed non-significant (p≤ 0.05) contribution of long-range transport to OCP pollution in Nairobi City. This indicated possible presence of point sources of environmental OCPs in the city. The water-air fugacity ratios indicated that volatilization and deposition played an important role in the spatial distribution of OCPs in Nairobi City. This indicated that contaminated surface waters could be major sources of human exposure to OCPs, through volatilization. The incremental lifetime cancer risks (ILCR) determined from inhalation of atmospheric OCPs were 2.3745  ×  10^?13 – 1.6845  ×  10^?11 (adult) and 5.5404  ×  10^?13 – 3.9306  ×  10^?11 (child) in the order: Dandora > Kibera > Industrial Area > City Square > Ngong’ Forest. However, these were lower than the USEPA acceptable risks, 10^?6 – 10^?4. This study concluded that atmospheric OCPs did not pose significant cancer risks to the residents.