SRHSC梁主要设计参数损伤敏感度分析

以型钢高强混凝土(SRHSC)梁为研究对象,结合SRHSC梁受力机理及承载能力的试验研究成果,提出了极限状态下的承载能力是评价梁力学性能的关键指标,将损伤前后梁正截面抗弯承载力之比和斜截面抗剪承载力之比的均值作为自变量,给出了SRHSC梁损伤表征函数,并借助"预定损伤法",揭示了主要设计参数对SRHSC梁损伤演化的影响规律。研究成果将为建立地震激励下SRHSC框架结构楼层损伤模型提供理论和数据支持。     

AHP based life cycle sustainability assessment (LCSA) framework: a case study of six storey wood frame and concrete frame buildings in Vancouver

Construction and building industry is in dire need for developing sustainability assessment frameworks that can evaluate and integrate related environmental and socioeconomic impacts. This paper discusses an analytic hierarchy process (AHP) based sustainability evaluation framework for mid-rise residential buildings based on a broad range of environmental and socioeconomic criteria. A cradle to grave life cycle assessment technique was applied to identify, classify, and assess triple bottom line (TBL) sustainability performance indicators of buildings. Then, the AHP was applied to aggregate the impacts into a unified sustainability index. The framework is demonstrated through a case study to investigate two six storey structural systems (i.e. concrete and wood) in Vancouver, Canada. The results of this paper show that the environmental performance of a building in Canada, even in regions with milder weather such as Vancouver, is highly dependent on service life energy, rather than structural materials.     

臭氧+曝气生物滤池深度处理工艺试验研究

针对某污水厂出水不达标的情况,本研究采用臭氧(O3)和曝气生物滤池(BAF)组合工艺对其进行深度处理.结果表明,当采用两级臭氧+曝气生物滤池工艺时,出水COD在31～46 mg/L,色度在13～29倍,均达到一级A排放标准.在最佳运行条件下,臭氧氧化使相对分子质量大于50 000的有机物含量减少10％,小于1 000的有机物含量增加14％.曝气生物滤池工艺使相对分子质量小于1 000的有机物含量降低了24％.     

Chloride Released from Three Permeable Pavement Surfaces after Winter Salt Application

Few studies exist on how chloride from chloride‐based deicers is transported in infiltration‐based stormwater control measures. In 2009, the U.S. Environmental Protection Agency (USEPA) constructed a 0.4 ha parking lot in Edison, New Jersey, that was surfaced with permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA). Each surface type has four equally sized, lined sections that direct all infiltrate to separate 5.7 m³ collection tanks. The USEPA acute criterion for aquatic life (860 mg/l) was exceeded in events immediately following a snow event. Concentrations of the infiltrate exceeded the detection limit (5 mg/l) year round but did not exceed the USEPA chronic toxicity (230 mg/l) after April. The chloride concentration decreased with cumulative rainfall since previous snow event, and a power regression described this relationship. In the power regression, the coefficient (b) described the initial concentration following a snow event, and the exponent (m) described the rate in which chloride was flushed through the system with infiltrating water. PC had the largest coefficient (5,664) and largest absolute exponent (?0.92), followed closely by PICP (b = 4,943 and m = ?0.87), and distantly by PA (b = 2,907 and m = ?0.67). The differences in release rate were proportional to the measured surface infiltration rates of 4,000; 2,400; and 200 cm/h for PC, PICP, and PA, respectively. These results will assist those who manage or regulate stormwater where receiving waters are chloride impaired.     

粉煤灰基质滤料生物过滤处理生活污水研究

将粉煤灰基质滤料用于曝气生物滤池,该滤料具有较高的比表面积和孔隙率,吸附性能良好,挂膜后生物相丰富。对于中等浓度的生活污水,当水力负荷和COD有机物负荷分别控制在1.53 m3/(m2.h)、3.68 kg/(m3.d)以下时,该曝气生物滤池COD和NH3-N去除率能稳定在85%以上,出水COD和NH3-N达到排放标准要求。该曝气生物滤池对进水水质水量的变动具有较强的抗冲击负荷能力。     

废弃混凝土对C_3S形成动力学的影响

废弃混凝土中石灰石的含量比较稳定,适合取代天然石灰石作为钙质原料配制水泥生料,并含有少量的SiO2,可以起部分硅质原料的作用。硬化的水泥浆体在高温下脱水形成氧化钙、氧化铝和氧化铁等氧化物,都是制造水泥所必须的氧化物。实验室利用20%和40%的废弃混凝土代替部分石灰石制备水泥熟料。研究了废弃混凝土对硅酸盐水泥熟料形成动力学的影响。用快速滴定法测定了不同熟料中f-CaO含量,根据文章提出CaO反应生成C3S的转化率,并用Amhenius公式计算了熟料中C3S形成反应的表观活化能。研究表明:废弃混凝土能改善生料的易烧性,并能降低熟料的烧成温度。     

BAF去除氨氮关键影响因素研究

为探讨曝气生物滤池去除氨氮的关键因素,选取沈阳仙女河污水处理厂(40万t/d)现场进行实地研究。通过测定不同条件下(pH、进水COD浓度、溶解氧、温度、水力负荷)的氨氮去除率,并进行主成分分析结果显示,影响BAF工艺脱氮的关键因素是温度、溶解氧和水力负荷。当温度在14~30℃之间时,氨氮的去除率一直维持较高,当温度低于14℃时,氨氮的去除率较低;随着溶解氧浓度的增大,氨氮的去除率也随之升高,当溶解氧增加到5.6 mg/L时,氨氮的去除率达到80%~90%,接近饱和状态;在水力负荷为3.08~4.15 m3/(m.2h)之间时,氨氮的去除率上升,超过该值,则氨氮去除率下降。     

超限结构无缝法施工在污水处理工程中的应用

介绍了一种在超限混凝土结构中取消伸缩缝或增大伸缩缝最大间距的新型施工方法——超限混凝土结构无缝法施工。论述无缝法施工的原理及膨胀加强带的设置,探讨UEA膨胀混凝土的配制,在实践的基础上总结了无缝法施工的方法、注意事项及优点。     

高强与高性能混凝土温湿度场应力分析

针对高强与高性能混凝土易于开裂的特点,对高强高性能混凝土早期温湿度场随龄期发展的分布情况以及混凝土的收缩变形进行理论分析,建立相应的计算模型,编制三维有限元程序,分析在外界温湿度变化以及不同养护条件下由混凝土内部温差和湿度变化产生的温度应力和干燥收缩应力,从施工养护方法上探讨了高强与高性能混凝土抗裂性能的改善措施.     

Usage of polystyrene disposable food dishes in the lightweight concrete making

The increasing use and subsequent accumulation of polystyrene containers has triggered a substantial environmental problem. This study investigated using varied percentages of solid waste polystyrene disposable food dishes in the production of lightweight concrete samples with 350 kilograms per cubic meter (kg/m³) of cement and a density of 1,300 kg/m³. The polystyrene disposable dishes were ground into beads of 0–3 millimeters (mm) and 3–6 mm in size. First, the characteristics of Type II Portland cement, polystyrene, and aggregates were examined. The following characteristics of concrete using ASTM International and British Standards Institution standards were tested: slump, compressive strength, ability to resist chloride ion penetration, and resistance of concrete to rapid freezing and thawing cycles. Scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy analytical techniques were also used. The slump of samples varied between 40 and 70 mm and was not dependent on either the polystyrene percentage or the size of the polystyrene beads in the concrete samples (p‐value > .05). The compressive strength of the concrete samples after 90 days of curing, and using different percentages of polystyrene, varied between 96 and 113 kilograms per square centimeter (kg/cm²). The resistance of the samples to the freezing and thawing cycle and chloride ion penetration were affected unfavorably by the presence of the polystyrene. The SEM technique indicated that concrete samples containing 15% and 25% polystyrene had denser crystals and less void than concrete samples with 40% and 55% polystyrene.