紫外光降解对生物过滤塔去除氯苯性能的影响机制研究

紫外-生物过滤联合工艺中的紫外单元促进了后续生物过滤单元的氯苯去除性能.为了进一步揭示紫外光降解对生物过滤塔运行性能的影响机制,本研究系统分析了紫外光降解对生物过滤塔填料层pH、生物膜特性和填料层结构特性等方面的影响.结果表明,氯苯紫外光降解产物导致了生物过滤单元填料层pH的下降(从pH 6～8降至pH 4～7);另外,紫外单元产生的臭氧降低了生物过滤单元生物膜厚度和生物膜的EPS含量,改善了生物膜的特性,提高了氯苯和营养物质在生物膜内的传质效率.同时,臭氧可以有效控制生物量过量积累,增加了填料层的比表面积(从784 m2.m-3增加至880 m2.m-3),优化了填料层的结构特性,提高了污染物的反应速率.上述各方面的综合作用最终促进了生物过滤单元的氯苯去除性能.     

基于遥感资料的中国东部地区植被VOCs排放强度研究

本研究充分基于遥感资料获取中国东部地区叶面积指数和叶生物量的最新信息,并广泛调研了植被VOCs排放因子的最新研究进展,以2008—2010年的植被和气象的平均状态为背景,基于MEGAN排放模型,研究了中国东部地区植被VOCs(BVOCs)排放的时空分布特征.结果表明,我国东部地区BVOCs年排放总量为11.3×106t(以C计,下同),其中异戊二烯(ISOP)、单萜烯(MON)和其它VOC(OVOC)质量分数(下同),分别为44.9%、31.5%、23.6%.BVOCs排放呈现明显的季节变化特征,春、夏、秋、冬4个季节分别占全年的11.2%、71.8%、14.1%和3.0%.空间分布上,排放高值区主要分布于大小兴安岭、长白山脉、秦岭大巴山脉、东南丘陵、海南等植被茂密的区域,年均排放强度一般在1500～6000kg·km-·2a-1之间,福建、广东、江西、浙江、湖南、湖北等省份BVOCs的排放总量与平均排放强度均较高.本研究所得到的高时空分辨率的BVOCs排放清单,可以为区域环境与气候的数值模拟研究提供基础.     

VOCs气体在活性炭上的二元吸附过程研究

采用穿透曲线法研究了4种VOCs在活性炭上的的二元吸附过程。研究表明:对于甲苯-苯、甲苯-丙酮、甲苯-乙酸乙酯、苯-丙酮、丙酮-乙酸乙酯二元吸附体系,吸附过程存在置换作用,即随着高沸点组分在床层内吸附量的逐渐增加,相对挥发性大的低沸点组分重新汽化而脱附,出现高沸点组分置换低沸点组分的现象,表现为被置换组分的穿透曲线上出现峰值。之后随着高沸点组分吸附趋于饱和,置换作用停止,低沸点组分吸附也趋于平衡。但对于沸点相近的苯-乙酸乙酯二元体系,吸附过程没有明显的置换现象。吸附量的计算结果表明,有机物在二元体系中的吸附量较同等条件时的单组分吸附量均有不同程度的降低,其中被置换组分降低程度较大,但总吸附量可近似按照浓度为二元组分总浓度低沸点组分的平衡吸附量的近似法计算,平均误差为7.9%。     

植物释放挥发性有机物(BVOC)向二次有机气溶胶(SOA)转化机制研究

利用自制玻璃生态罩,研究植物挥发性有机物（BVOC）的释放机制.在紫外光诱导条件下,BVOC经历一系列的光氧化反应,最终产生了二次有机气溶胶（SOA）.运用固相微萃取（SPME）和气相色谱-质谱联用（GC-MS）技术,对目标植物（驱蚊草）释放出的BVOC进行采样分析,共检测出7种主要化合物,其中主要为单萜类、倍半萜类、醇类和酮类物质.研究发现,在紫外光的照射下,这些BVOC可以发生光氧化反应转化为SOA.利用串联差分淌度分析仪（TDMA）测定SOA的粒径分布和SOA颗粒物的吸湿性.结果表明粒径范围大致是50～320 nm,吸湿性研究发现这些SOA具有吸湿性,生长因子可以从1.05增长到1.11.     

长江三角洲地区基于喷涂工艺的溶剂源VOCs排放特征

了解挥发性有机物(volatile organic compounds,VOCs)的溶剂源排放特征是制定长江三角洲地区PM2.5和臭氧防控策略的关键.本研究通过罐采样-GC-MS/FID测定了长江三角洲地区重点喷涂行业(集装箱喷涂、造船喷涂、木器喷涂和汽车喷涂业)的VOCs排放特征.结果表明,长江三角洲地区喷涂行业排放的主要VOCs组分为甲苯、二甲苯、乙苯等芳香烃类物质,三者之和占总VOCs的质量分数为79%~99%.生产工艺的不同对VOCs的排放组成影响并不大,废气处理装置中活性炭吸附对VOCs的组成并无明显影响,而催化燃烧的处理过程会使VOCs的排放组成产生显著变化,乙烯排放明显增大,同时也使得催化燃烧处理最大增量反应活性(maximum increment reactivity,MIR)值高于活性炭吸附处理后的MIR值,说明不同的处理措施的使用将影响VOCs对臭氧的生成作用.     

京津冀天然源挥发性有机物排放研究

为探明2017年京津冀地区天然源挥发性有机物(BVOCs)的空间分布,将研究区划分成3 km分辨率的格网,并通过WRF模型提供气象驱动数据,MODIS影像提供植被功能类型和叶面积指数,最终利用MEGAN模型进行模拟研究.结果表明,该模型将BVOCs分成147个细类,其中主要有异戊二烯、单萜烯41类、半萜烯32类、其他VOC73类.2017年京津冀地区BVOCs排放总量为426.26×10~3 t,四大类别的排放比例依次为29.38%、12.32%、6.24%、52.05%.单萜烯中排放较高的类别是α-蒎烯、β-蒎烯、t-β-罗勒烯,而半萜烯中排放较高的是α-法呢烯和β-石竹烯.整个研究区域内BVOCs排放较高的区域位于北部森林与灌丛分布密集的燕山山脉和西南的太行山山脉,其中主要的城市有承德、北京、张家口、保定、石家庄等.排放量较低的地区为廊坊、衡水、天津等地.本研究通过模型模拟得到了京津冀地区2017年高时空分辨率BVOCs排放清单,同时可为以后的大气环境研究提供基础数据.     

国家干线公路移动源VOCs排放及臭氧生成潜势研究

基于国家干线公路4346个交通监测站日平均监测数据,采用移动源VOCs测算方法,建立国家干线移动源VOCs排放清单,使用最大增量反应活性（MIR）估算VOCs的臭氧生成潜势（OFP）,并通过动态分段技术和核密度估计方法对臭氧生成强度的空间特征进行分析.结果表明,客车是国家干线移动源VOCs年排放量最大的源,占客货总排放量70.50%;广东省年排放量最大,占全国干线公路VOCs排放量的10.7%;G15沈海高速年排放量最大,占全国干线公路VOCs排放量的5.4%.烯烃和芳香烃为移动源OFP主要的贡献者,前十种有机污染物占干线移动源总OFP的67.29%.从客货车日均OFP强度上来看,受车流量影响,各干线差异明显.北京天津呈团簇状集聚,至石家庄一线为带状分布;济南淄博潍坊青岛一线呈弯月带状分布;南京苏州上海杭州呈团状,至上海又集聚;粤港澳大湾区以深圳为中心高度聚集;沈阳、郑州、西安、武汉、重庆等交通枢纽出现次一级强度集聚.     

太原市夏季大气VOCs污染特征及臭氧生成潜势

2018年8月采集太原市大气样品,分析太原市夏季大气VOCs的污染特征,并利用最大增量反应活性系数法（MIR系数法）估算了VOCs的臭氧生成潜势（OFP）.结果表明,太原市夏季大气VOCs浓度为17.36~89.60μg/m³,其中烷烃占比58.01%、芳香烃占比20.06%、烯烃占比16.52%、炔烃占比5.40%.大气VOCs浓度变化表现为明显的早晚双高峰特征,且以早高峰影响为主.OFP分析显示,烷烃、烯烃、芳香烃、炔烃分别占总OFP的19.16%、47.74%、31.75%、1.35%,C₃~C₅类烯烃是活性较高的物种,对O₃生成贡献较大.     

The ignored emission of volatile organic compounds from iron ore sinter process

Iron ore sintering is a major source of gaseous and particulate pollutants emission in iron smelt plant. The aim of present study is to characterize the volatile organic compounds(VOCs) emission profiles from iron ore sintering process. Both sinter pot test and sinter simulation experiment were conducted and compared. Out results showed that sinter process produced large quantity of VOCs together with NOxand SO_2. VOCs and NO were produced simultaneously in sinter pot test from 3 to 24 min after ignition, flowed by SO_2 production from 15 min to the end of sintering. Total VOCs(TVOC) concentration in sinter flue gas was affected by the coal and coke ratio in sinter raw material. The maximum TVOC concentration was 34.5 ppm when using 100% coal as fuel. Sinter simulation experiments found that the number of VOCs species and their concentrations were found by sinter temperature. The largest VOCs species varieties were obtained at 500 °C. Benzene, toluene,xylene and ethylbenzene were major VOCs in sinter flue gas based on the results from both simulation test and sinter pot. It thus demonstrated that in addition to NO_x, SO_2 and metal oxide particles, sinter flue gas also contained significant amount of VOCs whose environmental impact cannot be ignored. Based on our work, it is timely needed to establish a new VOC emission standard for sinter flue gas and develop advanced techniques to simultaneously eliminate multi-pollutants in iron ore sinter process.     

Characteristics of volatile organic compounds, NO2, and effects on ozone formation at a site with high ozone level in Chengdu

Chengdu is a megacity in the southwest of China with high ozone (O₃) mixing ratio. Observation of volatile organic compounds (VOCs), NO₂ and O₃ with high temporal resolution was conducted in Chengdu to investigate the chemical processes and causes of high O₃ levels. The hourly mixing ratios of VOCs, NO₂, and O₃ were monitored by an online system from 28 August to 7 October, 2016. According to meteorological conditions, Chengdu, with relative warm weather and low wind speed, is favorable to O₃ formation. Part of the O₃ in Chengdu may be transported from the downtown area. In O₃ episodes, the average mixing ratios of NO₂ and O₃ were 20.20?ppbv and 47.95?ppbv, respectively. In non-O₃ episodes, the average mixing ratios of NO₂ and O₃ were 16.38?ppbv and 35.15?ppbv, respectively. The average mixing ratio of total VOCs (TVOCs) was 40.29?ppbv in non-O₃ episodes, which was lower than that in O₃ episodes (53.19?ppbv). Alkenes comprised 51.7% of the total O₃ formation potential (OFP) in Chengdu, followed by aromatics which accounted for 24.2%. Ethylene, trans-pentene, propene, and BTEX (benzene, ethylbenzene, toluene, m/p-xylene, o-xylene) were also major contributors to the OFP in Chengdu. In O₃ episodes, intensive secondary formations were observed during the campaign. Oxygenated VOCs (OVOCs), such as acetone, Methylethylketone (MEK), and Methylvinylketone (MVK) were abundant. Isoprene rapidly converted to MVK and Methacrolein (MACR) during O₃ episodes. Acetone was mainly the oxidant of C3-C5 hydrocarbons.