水产品加工废水生物处理现状与展望

介绍了几种较为典型的水产品加工废水生物处理工艺,以及利用生物处理工艺处理高含盐量废水实验室研究结果;展望了水产品加工废水处理技术的发展前景。     

Biological pretreatment of Yellow River water

Bio-ceramic filter(BF) and moving-bed biofilm reactor(MBBR) were used for biological pretreatment of Yellow River water in this study. The BF only had slight advantage over MBBR for TOC and ammonia removal. However, like UV254, the average removal rate of THMFP in the BF was much higher than that in the MBBR. UV254 removal did not show obvious correlation with trihalomethane formation potential(THMFP) removal. Hexachlorocyclohexane could be effectively removed in both BF and MBBR. As for diatom and cyanobateria removal the MBBR had better performance than the BF, which was contrary to the average chlorophyll-a(Chl-a) removal rate. The proposal was made in this study that biological flocculation and sedimentation of sloughed biofilm should play a more important role on algae removal in the MBBR than in the BF. The BF and MBBR could effectively remove microcystins. Moreover, MBBR could be a promising technology for biological pretreatment.     

UBAF与纤维球过滤结合工艺应用于污水回用的试验研究

利用升流式曝气生物滤池 (UBAF)与纤维球过滤相结合的工艺对城市污水进行深度处理 ,使其达到回用的要求。结果表明 :对于经过二级处理后的可生物降解性较差的城市污水 ,应用UBAF和纤维球过滤相结合的处理工艺能够取得很好的效果 ,处理后的污水完全可以达到污水排放的一级标准和城市生活杂用水的标准     

粉煤灰在城市固体废物好氧填埋中应用的研究

从理论和实验两方面系统地阐述了粉煤灰在城市固体废物 (MSW)好氧填埋中的应用。粉煤灰具有良好的吸附性能及pH值调节能力 ,与MSW按适当比例混合后进行好氧填埋 ,能够弥补城市固体废物好氧填埋的不足 ,更能有效地降解垃圾 ,尤其是对垃圾渗滤液具有更好的降解效果     

草浆造纸中段废水的生物处理动力学

利用静态溶解氧消耗速率（OUR）试验模拟草浆造纸中段废水生物处理的生化反应过程,并运用Lawrence-McCarty模式进行了动力学分析。由OUR试验结果和小试研究结果建立的草浆造纸中段废水好氧生物处理的动力学方程为v=0.72S/(60.43 S）。将该动力学方程预测结果和实际工程的运行数据进行了比较,结果表明,动力学方程的比基质降解速率预测值高于实际工程的计算值,分析原因可能在于：实际工程中中段废水中的纤维素类悬溪物在生物处理装置的积累导致了污泥活性的降低。     

TVS／TFS去除率在ATAD污泥稳定评价的应用

在ATAD(Autothermal Thermophilic Aerobic Digestion,自升温高温好氧消化)工艺污泥稳定评价中引入TFS．提出“TVS/ TFS去除率”的概念,得出“TVS/TFS去除率”可以代替“VS(g)去除率”而成为一种新的污泥稳定指标的结论;采用数学微分的方法分析了“TVS/TFS去除率”和“VS(g)去除率”的数据误差问题,进泥TS为60g/L,TVS/TS为56％的运行条件下,前者的最大数据误差仅为3．16％,远小于后者的误差最大值15．45％,即引入TFS解决了“VS(g)去除率”数据波动大的问题;TFS的引入还节约了污泥稳定研究所需的时间和工作量。     

造气含氰废水的生物治理

在塔式生物滤池生产性处理规模上考察了造气含氰废水在挂膜前后的处理效果。比较结果表明，未挂过氰化物的平均处理率仅为７９．２９％，挂膜后的处理率平均为９５．２６％，处理后的废水全部回用于生产，减少了氰化物的排放量，防止了造气废水对环境的污染。     

序列间歇式好氧活性污泥法处理生物制药废水研究

本研究采用好氧ＳＢＲ法处理生物制药废水。试验结果表明，废水中不需另加氮磷营养物质，当进水ＣＯＤＣｒ为９１１～３２８０ｍｇ／Ｌ时，在曝气１６ｈ条件下，出水ＣＯＤＣｒ在３５０ｍｇ／Ｌ以下，ＢＯＤ５在８０ｍｇ／Ｌ以下，ＳＳ在１５０ｍｇ／Ｌ以下，皆达到生物制药工业废水二级排放标准。本文还对好氧ＳＢＲ法的有机物降解动力学过程进行了研究。     

Effect of catalyzed diesel particulate filter and its catalyst loading on emission characteristics of a non-road diesel engine

In this study, the effects of a diesel oxidation catalyst (DOC) coupled with a catalyzed diesel particulate filter (CDPF) with different catalyst loadings on the power, fuel consumption, gaseous and particulate emissions from a non-road diesel engine were investigated. Results showed that the after-treatment had a negligible effect on the power and fuel consumption. The reduction effect of the DOC on the CO and hydrocarbon (HC) increased with the engine load. Further reductions occurred coupling with the CDPF. Increasing the catalyst loading resulted in a more significant reduction in the HC emissions than CO emissions. The DOC could increase the NO₂ proportion to 37.9%, and more NO₂ was produced when coupled with the CDPF below 250°C; above 250°C, more NO₂ was consumed. The after-treatment could reduce more than 99% of the particle number (PN) and 98% of the particle mass (PM). Further reductions in the PN and PM occurred with a higher CDPF catalyst loading. The DOC had a better reduction effect on the nucleation particles than the accumulation ones, but the trend reversed with the CDPF. The DOC shifted the particle size distribution (PSD) to larger particles with an accumulation particle proportion increasing from 13% to 20%, and the geometric mean diameter (GMD) increased from 18.2 to 26.0 nm. The trend reversed with the CDPF and the accumulation particle proportion declined to less than 10%. A lower catalyst loading on the CDPF led to a higher proportion of nucleation particles and a smaller GMD.     

唐钢一炼钢厂VD精炼炉直接冷却水系统设计

介绍了VD精炼炉直接冷却水处理常用的工艺流程及设计中应重点考虑的问题 ,如水处理单元的选择 ,供水泵与提升泵的匹配问题等