新型材料淀粉微球对Cu2＋、Cr3＋和Pb2＋的吸附机理研究

以可溶性淀粉为原料,在反相悬浮体系中合成N,N′-亚甲基双丙烯酰胺交联淀粉微球为载体,研究了新型吸附材料淀粉微球（cross-linked starch microsphere,CSMs）对Mn＋（Cu2＋、Cr3＋、Pb2＋）的静态吸附行为。利用扫描电镜、X射线衍射仪和红外光谱仪对微球及其吸附产物进行表征,分析讨论了3种金属原子结构,研究了吸附机理。结果表明：308K时,Cu2＋、Pb2＋和Cr3＋的饱和吸附量分别是2.43、0.30和0.27 mmol/g,CSMs对Cu2＋离子吸附能力最强,并且其通过物理吸附、配位吸附方式吸附Mn＋,并得出引起微球吸附能力大小可能与金属离子电荷、离子半径和外层电子排布的差异因素有关。     

非活体生物质对水中活性艳红X-3B的吸附研究

研究了4种非活体生物质(米酒糟、花生壳、柚子皮、稻草秸秆)对模拟废水中活性艳红X-3B的吸附条件及吸附机理。结果表明,活性艳红X-3B初始浓度为100 mg/L、pH为1.0~2.0、吸附剂浓度为10 mg/L时,4种吸附剂对活性艳红X-3B的吸附率可达到80%。吸附在60 min左右达平衡后最大吸附量的顺序为:米酒糟(58.8 mg/g)花生壳(28.0mg/g)柚子皮(23.6 mg/g)稻草秸秆(19.5 mg/g)。在达最大吸附率时,米酒糟的用量可减少一半、pH范围可宽为1.0~6.0,且吸附量是另三者的2倍以上。综合比较,米酒糟具有较强的吸附废水中活性艳红X-3B的能力,可作为废水中活性染料的吸附剂使用。而花生壳、柚子皮和稻草秸秆的吸附能力相对较弱,不是理想的吸附材料。数学模型模拟表明,米酒糟和柚子皮的吸附过程更符合Freundlich方程,而花生壳和稻草秸秆更符合Langmuir方程;动力学研究表明4种吸附剂的吸附拟合更符合拟二级动力学方程。     

铁炭复配修复地下水中NO_3~--N的条件研究

采用了铁炭复配修复地下水中NO3--N,探讨了实验条件对修复效果的影响。结果表明,在pH值近中性条件(初始pH 6.42)下,反应时间为1 h时NO3--N修复率达到60.85%;Fe/C=1∶1时介质最佳用量分别为4~5 g;Fe/C=1/1.5时修复率为72.80%;反应速率在高振荡强度下大于低振荡强度;氧化铜的催化效果最好,可使修复率提高7.5个百分点。铁炭复配介质修复地下水中NO3--N是有效可行的,修复率随反应时间的增加而提高,在Fe/C=1∶1时修复率与介质用量呈正相关,无限减小Fe/C比并不能无限提高修复率,振荡强度对修复具有显著影响,低振荡强度下的修复过程较高强度存在滞后现象,并非所有金属氧化物催化剂对铁炭修复NO3--N均有促进作用。     

烟草下脚料发酵制取乙醇

通过单因素实验考察了硫酸浓度、固液比和水解时间对硫酸水解的影响。结果显示最优条件为:硫酸浓度为50%(w/w),固液比为10%(w/v),时间为100 min。烟草下脚料在最佳硫酸水解条件下,经5倍稀释,中和pH值至5～6。取经过滤后的水解液(FH)用酿酒酵母(Sacchharomyces cerevisiae)发酵产生乙醇,最大的乙醇浓度和乙醇产量分别为1.09g/L和54.5 g/kg。未过滤水解液(UFH,包括水解残渣)加入纤维素酶(70 U/100 mL)和酿酒酵母(Sacchharomyces cerevisiae)进行发酵,最大的乙醇浓度和乙醇产量分别为1.23 g/L和61.5 g/kg。     

酸雨对建筑材料的影响及防治研究综述

综合分析了酸雨对建筑外墙的涂料、石材、混凝土等主要建筑构件的腐蚀原理,并提出了防治措施,来预防酸雨对建筑材料的侵害。     

基于品牌创建模型的主题公园可持续发展研究

通过对主题公园研究文献的综述分析,指出主题公园研究中品牌化研究较为匮乏.而中国主题公园近二十年的发展历程表明,主题公园存在的生命周期短暂性现象的主要原因是缺乏品牌创新.从生命周期及可持续发展的视角,提出了以品牌为核心的主题公园运营模式,以此为指导构建了包括概念层、主体层以及基础层三个层面的主题公园品牌创建模型,即通过对动态市场的研究,设计、宣传和推广自身的原创品牌,在获得相应的品牌价值之后,将品牌价值向外延伸,通过系统内各部分的紧密合作,获得主题公园可持续发展的内在驱动力.最后,着重从原创品牌的构建、品牌价值的延伸和保障因素兰方面,提出了基于品牌创建模型的主题公园可持续发展策略.该策略表明:主题公园必须在丰厚的文化内涵和更高的游客体验价值基础上强化自身品牌的构建和发展,在品牌站稳于市场时要适当适度地进行品牌价值延伸,这才能保证主题公园经营的可持续发展.     

拜耳法赤泥粒径分级预处理的研究

赤泥是从铝土矿中提取氧化铝的过程中产生的工业废渣.分析了拜耳法赤泥的粒径分布,以及主要化学组成和矿物组成在不同粒径赤泥中的变化规律.在此基础上,提出先将赤泥粒径分级预处理,然后根据粗细粒径赤泥的差异分别进行回收利用的思路.研究结果表明,赤泥中粒径大于0.075 mm的粗颗粒以铁、硅、钙为主,实践证明可以通过磁选或重选工...     

纳米氧化物对钙基材料在高温燃煤中除砷脱硫的促进机理研究

将纳米MgO、Al2O3和ZnO分别添加于CaCO3中制备出钙基纳米氧化物复合吸附剂,进行了燃煤过程中除砷脱硫的实验研究;对燃煤灰渣进行了比表面积及孔隙度分析、X-射线衍射分析和扫描电镜观察,探讨了纳米MgO对CaCO3除砷脱硫的促进机理。结果表明,添加了纳米MgO的复合吸附剂除砷脱硫性能最好,比单一的CaCO3除砷率和脱硫率分别高出了28．73％和37．21％,表现出同时除砷脱硫的良好性能;其促进机理是纳米MgO的加入改变了灰样的微观结构促进了气相间的流动使得灰渣孔隙明显扩大,提高了CaO与As2O3和SO2反应的能力;在除砷的反应中生成了新的物质Ca3Mg2（AsO4）2,在一定程度上抑制了除砷产物的分解。     

Recycling of organic materials and solder from waste printed circuit boards by vacuum pyrolysis-centrifugation coupling technology

Here, we focused on the recycling of waste printed circuit boards (WPCBs) using vacuum pyrolysis-centrifugation coupling technology (VPCT) aiming to obtain valuable feedstock and resolve environmental pollution. The two types of WPCBs were pyrolysed at 600°C for 30 min under vacuum condition. During the pyrolysis process, the solder of WPCBs was separated and recovered when the temperature range was 400-600°C, and the rotating drum was rotated at 1000 rpm for 10 min. The type-A of WPCBs pyrolysed to form an average of 67.91 wt.% residue, 27.84 wt.% oil, and 4.25 wt.% gas; and pyrolysis of the type-B of WPCBs led to an average mass balance of 72.22 wt.% residue, 21.57 wt.% oil, and 6.21 wt.% gas. The GC-MS and FT-IR analyses showed that the two pyrolysis oils consisted mainly of phenols and substituted phenols. The pyrolysis oil can be used for fuel or chemical feedstock for further processing. The recovered solder can be recycled directly and it can also be a good resource of lead and tin for refining. The pyrolysis residues contained various metals, glass fibers and other inorganic materials, which could be recovered after further treatment. The pyrolysis gases consisted mainly of CO, CO(2), CH(4), and H(2), which could be collected and recycled.     

Chitosan/albumin/CaCO3 as mimics for membrane bioreactor fouling: genesis of structural mineralized-EPS-building blocks and cake layer compressibility

Membrane bioreactor biofouling is usually described as an extracellular matrix in which biopolymers, inorganic salts and active microbes co-exist. For that reason, biomineralization (BM) models can be useful to describe the spatial organization and environmental constraints within the referred scenario. BM arguments were utilized as background in order to (1) evaluate CaCO₃ influence on flux decline; pore blocking and cake layer properties (resistance, permeability and compressibility) in a wide range of Chitosan/Bovine serum albumin (BSA) mixtures during step-pressure runs and, (2) perform membrane autopsies in order to explore the genesis of mineralized extracellular building blocks (MEBB) during cake layer build up. Using low molecular weight chitosan (LC) and BSA, 2 L of 5 LC/BSA mixtures (0.25-1.85 ratio) were pumped to an external ultra filtration (UF) membrane (23.5 cm², hydrophobic, piezoelectric, 100 kDa as molecular weight cut-off). Eight different pressure steps (40 ± 7 to 540 ± 21 kPa) were applied. Each pressure step was held for 900 s. CaCO₃ was added to LC/BSA mixtures at 0.5, 1.5 and 3 mM in order to create MEBB during the filtration tests. Membrane autopsies were performed after the filtration tests using thermo gravimetric, scanning microscopy and specific membrane mass (mg cm⁻²) analyses. Biopolymer-CaCO₃ step-pressure filtration created compressible cake layers (with inner voids). The formation of an internal skeleton of MEBB may contribute to irreversible fouling consolidation. A hypothesis for MEBB genesis and development was set forth.