含氮消毒副产物卤乙酰胺的水解特性

为探究高毒性含氮消毒副产物HAcAms（卤乙酰胺）的水解特性,选取水中普遍存在的2种溴代HAcAms[BCAcAm（溴氯乙酰胺）、DBAcAm（二溴乙酰胺）]与2种氯代HAcAms[DCAcAm（二氯乙酰胺）、TCAcAm（三氯乙酰胺）]作为研究对象,研究pH、初始ρ（HAcAms）、温度、氯消毒剂和氯胺消毒剂等因素对HAcAms稳定性的影响.结果表明:①4种HAcAms在pH为5和7时较稳定,在pH为8~10下发生碱性催化水解反应,并且水解速率随pH升高而增加.②相同碱性环境中,4种HAcAms的水解速率大小依次为TCAcAm > DCAcAm > BCAcAm > DBAcAm,并且初始ρ（HAcAms）（30~150 μg/L）越小,温度（25~35℃）越高,HAcAms水解速率越大.③中性条件下,4种HAcAms在ρ（NaClO）（NaClO为次氯酸钠）为1~5 mg/L时均迅速氯化分解,并且分解速率随ρ（NaClO）增加而增大,4种HAcAms分解速率的大小规律与其碱性水解速率大小规律一致.④当pH为7时,4种HAcAms在ρ（NH₂Cl）（NH₂Cl为一氯胺）为0.5~5 mg/L下较稳定.研究显示,水中HAcAms在高pH、低初始ρ（HAcAms）、高温及氯消毒剂存在的条件下易水解,其中溴代HAcAms比氯代HAcAms更稳定,其在饮用水与再生水中的风险更需要重视.      

高藻水臭氧预氧化过程有机物转化及消毒副产物生成势

研究了高藻水预氧化处理过程中,不同臭氧氧化程度及不同pH值条件下,藻类有机物释放与转化规律以及氯化消毒副产物(DBPs)的生成特性.结果表明,臭氧投加量为28.92 mg·L-1时藻去除率达36%.随着臭氧投加量的增加,藻的去除率进一步增加,类腐殖酸先增加后持续减少,溶解性微生物代谢产物、类富里酸和类芳香蛋白物质持续减少;低投加量的臭氧对二氯乙腈(DCAN)、三氯乙腈(TCAN)生成势有明显的控制作用,但会增加三氯硝基甲烷(TCNM)以及1,1,1-三氯丙酮(1,1,1-TCP)前体物,随臭氧投加量增大,DBPs生成势显著增大.酸性条件下臭氧对藻的去除效果最好,UV254以及总有机碳(DOC)均随pH的增大有所上升,但变化较小;臭氧氧化可降解溶解性微生物代谢产物,降解效果受pH影响较小,类腐殖酸有机物随pH值增大而减少;DCAN、TCAN生成势随pH增大有所降低,TCNM生成势在pH=10条件下最高,1,1,1-TCP生成势在pH=7条件下最高.     

Impact of combining chlorine dioxide and chlorine on DBP formation in simulated indoor swimming pools

The main objective of this study was to assess the combined use of chlorine dioxide (ClO2) and chlorine (Cl2) on the speciation and kinetics of disinfection by-product (DBP) formation in swimming pools using synthetic pool waters prepared with a body fluid analog (BFA) and/or fresh natural water. At 1:25 (mass ratio) of ClO2 to Cl2, there was no significant reduction in the formation of trihalomethanes (THMs) and haloacetic acids (HAAs) for both BFA solution and natural water compared to the application of Cl2 alone. When the mass ratio of ClO2 to Cl2 increased to 1:1, substantial decreases in both THMs and HAAs were observed in the natural water, while there was almost no change of DBP formations in the BFA solution. Haloacetonitriles and halonitromethanes levels in both water matrices remained similar. In the presence of bromide, the overall DBP formation increased in both BFA solution and natural water. For the DBP formation kinetics, after 72 hr of contact time, very low formation of THMs and HAAs was observed for the use of ClO2 only. Compared to Cl2 control, however, applying the 1:1 mixture of ClO2/Cl2 reduced THMs by > 60% and HAAs by > 50%. Chlorite was maintained below 1.0 mg/L, while the formation of chlorate significantly increased over the reaction time. Finally, in a bench-scale indoor pool experiment, applying ClO2 and Cl2 simultaneously produced less THMs compared to Cl2 control and kept chlorite at < 0.4 mg/L, while HAAs and chlorate accumulated over 4-week operation period.     

Showering in Flint, MI: Is there a DBP problem?

Lead contamination in the City of Flint, MI has been well documented over the past two years, with lead levels above the EPA Action Level until summer 2016. This resulted from an ill-fated decision to switch from Detroit water (Lake Huron) with corrosion control, to Flint River water without corrosion control. Although lead levels are now closer to normal, reports of skin rashes have sparked questions surrounding tap water in some Flint homes. This study investigated the presence of contaminants, including disinfection by-products (DBPs), in the hot tap water used for showering in the homes of residents in Flint. Extensive quantitative analysis of 61 regulated and priority unregulated DBPs was conducted in Flint hot and cold tap water, along with the analysis of 50 volatile organic compounds and a nontarget comprehensive, broadscreen analysis, to identify a possible source for the reported skin rashes. For comparison, chlorinated hot and cold waters from three other cities were also sampled, including Detroit, which also uses Lake Huron as its source water. Results showed that hot water samples generally contained elevated levels of regulated and priority unregulated DBPs compared to cold water samples, but trihalomethanes were still within regulatory limits. Overall, hot shower water from Flint was similar to waters sampled from the three other cities and did not have unusually high levels of DBPs or other organic chemicals that could be responsible for the skin rashes observed by residents. It is possible that an inorganic chemical or microbial contaminant may be responsible.     

单过硫酸氢钾复合粉在饮用水消毒过程中的副产物生成特性及遗传毒性变化

以北京田村山净水厂原水和炭后出水作为试验用水,对新型消毒剂单过硫酸氢钾复合粉消毒后生成的消毒副产物(disinfection by-products,DBPs)进行定性分析.向受试水样中分别投加单过硫酸氢钾复合粉和次氯酸钠,比较了复合粉消毒和氯消毒的DBPs生成量,并通过umu试验对水样消毒后的遗传毒性变化进行测试.结果表明,测试水样投加单过硫酸氢钾复合粉消毒前后的有机物种类变化不大,但仍有新的卤代烃和卤代物生成.与氯消毒相比,单过硫酸氢钾复合粉消毒后生成的三卤甲烷(THMs)和卤乙酸(HAAs)的含量更低.另外,根据umu测试的结果,经单过硫酸氢钾复合粉消毒后原水和炭后水的遗传毒性均明显低于氯消毒.然而在水中有机物较多和消毒剂投加量较大时,单过硫酸氢钾复合粉用于消毒仍有一定安全风险.     

化学预氧化对苏氨酸生成三氯乙醛的影响

以具有最大比三氯乙醛生成潜能(SCHFP)的苏氨酸为研究对象,分析了次氯酸钠(NaClO)、二氧化氯(ClO_2)、高锰酸钾(KMnO_4)、过氧化氢(H_2O_2)、臭氧(O_3)和臭氧过氧化氢(O_3/H_2O_2)等预氧化剂对三氯乙醛(CH)生成的影响,以确定合适的预氧化剂及其适宜投加量,为CH的控制提供指导.结果表明,能够有效去除一天CH生成量(CH1d)的预氧化方式依次为H_2O_2、ClO_2、KMnO_4和NaClO,适宜投加量分别为3、0.5、0.6和0.5mg·L-1,对CH1d相应的去除率分别为61.54%、47.63%、29.77%和10.94%;能够有效去除CH生成潜能(CHFP)的预氧化方式依次为KMnO_4、NaClO、H_2O_2和ClO_2,适宜投加量分别为0.6、0.5、3和0.5mg·L~(-1),对CHFP相应的去除率分别为41.01%、33.38%、8.36%和2.40%;O_3和O_3/H_2O_2预氧化能够使CH1d和CHFP增加,不适用于对CH的控制.     

南水北调中线工程总干渠河南段原水中消毒副产物前体物变化规律

以取自南水北调中线总干渠河南段沿线10个分水口门的原水为研究对象,探究了原水中有机物的相对分子质量分布和亲疏水性分布规律;并且研究了原水在氯化和氯胺化条件下消毒副产物生成潜能的变化规律.分离实验结果表明,南水北调沿程原水中的有机物以小分子和强疏水性为主,1×103区间的溶解性有机碳(DOC)所占的比例最大,质量分数约为57%,强疏水性组分的DOC含量最高,占到总量的50%左右;氯化及氯胺化消毒副产物生成潜能分析实验结果表明,氯化及氯胺化后主要生成了两种含碳消毒副产物(三氯甲烷和一溴二氯甲烷)和两种含氮消毒副产物(二氯乙腈和三氯硝基甲烷).氯化三氯甲烷生成潜能约为120μg·L-1,与氯化生成潜能相比,氯胺化三氯甲烷生成潜能减少了90%左右,一溴二氯甲烷减少了84.9%左右,生成的两种含氮消毒副产物增加了,其中二氯乙腈的生成量增加了约2.3倍,但总含氮消毒副产物生成潜能仍旧较低,均小于6μg·L-1.本研究成果可为南水北调中线工程河南段沿线城市的水厂工艺选择和优化提供有效的理论和技术支持.     

Monitoring trihalomethanes in water by differential ultraviolet spectroscopy

Ultraviolet (UV) spectroscopy is a valid surrogate for monitoring the formation of disinfection by-products (DBPs). Sodium thiosulphate is commonly used to remove disinfectant residual. However, it produces interferences with absorbance in the UV region. Relationship between trihalomethane (THM) formation and differential UV absorbance (−ΔA _λ ) was explored in the presence of sodium thiosulphate. Chlorination of two synthetic and five natural waters was carried out. Sodium thiosulphate showed high UV absorption at 254 nm. This effect can be overcome selecting a higher wavelength. Optimum wavelength varied being about 290 nm for fulvic acid and 300 nm for humic acid type natural organic matter. Correlation between THMs formation and −ΔA _λ was linear for all the analysed samples. Regression curves do not pass through zero indicating the existence of a threshold absorbance decreasment. Once it is surpassed THM release begins. Chlorination of surface waters showed that the presence of bromide significantly increases THMs vs. −ΔA _λ slope. Furthermore, slope decreased with the aromaticity–hydrophobicity of organic matter.     

饮用水中有机物组成及控制技术

介绍了饮用水中有机物的组成及其去除评价指标,并指出了各类有机污染物对饮用水水质的影响。重点探讨了水中各类有机污染物的去除方法：强化混凝、颗粒活性碳、膜过滤、光催化氧化、臭氧一生物活性炭及生物预处理技术等。最后总结了各种处理方法的优缺点,为选择合适的去除有机污染物工艺提供参考。     

饮用水中卤氧化物离子色谱分析方法研究

直接大体积进样,建立生活饮用水中卤氧化物溴酸盐(BrO3-)、亚氯酸盐(ClO2-)、氯酸盐(ClO3-)含量的离子色谱(IC)法。优化的色谱条件为:Metrosep A Supp 7(250 mm)色谱柱配以Metrosep A Supp1保护柱,淋洗液为3.6 mmol/L Na2CO3与1.0 mmol/L NaHCO3;流速为0.6mL/min;进样量为100μL,抑制型电导检测器。方法结果显示:卤氧化物与常见共存阴离子完全分离,标准曲线在(5.0～400)μg/L范围内具有良好的线性关系(r>0.999),精密度高(相对标准偏差RSD<5.0%),样品加标平均回收率在90.8%~105%之间。按S/N=3,BrO3-、ClO2-、ClO3-的检出限分别为(0.9、0.7、1.0)μg/L。该方法操作简单、分离效果好,可与常见阴离子实现同时分析,灵敏度高,重现性好,适合于饮用水中消毒副产物中溴酸盐、亚氯酸盐、氯酸盐的同时测定。