缝洞型管道瓦斯爆炸特性数值模拟研究

为探究采空区遗煤、松散破碎岩块对瓦斯爆炸的影响,建立缝洞型管道模型,采用数值模拟与理论分析结合方法研究采空区内缝洞型管道内瓦斯爆炸的传播规律及管道长径比对瓦斯爆炸过程中速度与冲击波的影响。研究结果表明:在缝洞型结构内,随着火焰沿管道向前传播,各监测点速度逐渐变大、压力先增加后降低,而压力上升速率则表现出不规则的变化;缝洞结构加剧了火焰燃烧的剧烈程度,提高了管道内各监测点的温度峰值;在缝洞型管道内随长径比r增加,各监测点最大压力峰值以及速度大小依次降低。     

汽车用聚合物材料火灾燃烧特性研究

为研究车用聚合物材料的燃烧特性,并对材料的火灾危险性进行全方位的评估,采用锥形量热仪,对汽车上常用的ABS,PP-PVC,PVC革-无纺毡以及无纺布-PVC聚合物材料进行分析表征,测得点燃时间、热释放速率、总热释放量、质量损失速率、烟气生成速率等参数。结果表明:ABS材料的点燃危险性相对最低,PVC革-无纺毡材料相对最高;随热辐射强度的增加,各样品的热释放速率和烟气生成速率明显加快;结合热释放速率峰值、均值和总热释放量可知,无纺布-PVC材料的热危险性相对最低;结合烟气生成速率和总烟释放量可知,ABS材料的发烟危害性相对最高,无纺布-PVC的相对最低;综合比较各样品的FGI和FPI值,安全等级由高到低依次为ABS,PP-PVC,PVC革-无纺毡,无纺布-PVC。     

变压器油池火燃烧规律的实验研究*

为对变压器油池火灾进行准确有效的灭火,研究不同尺寸和不同厚度下变压器油的火灾动力学特征和基本燃烧特性,具体分析变压器油的燃烧过程和变压器油燃烧速率、火焰温度以及辐射热流随油池直径以及厚度的变化规律。结果表明:整个油品的燃烧过程分为预热燃烧阶段、稳定燃烧阶段和火焰熄灭阶段。对于厚度大于10 mm的油池燃烧,稳定阶段的燃烧速率与油层厚度无关,稳定阶段的燃烧速率随着油池直径的增加而增加。同时,变压器油火灾连续火焰区温度接近750 ℃。对于稳定燃烧阶段下的变压器油燃烧,基于辐射通量可得出在燃烧过程中,辐射热量占总燃烧热的占比约为1/3。研究结果可丰富变压器油燃烧的基础数据,为变压器火灾的灭火提供参考。     

基于非线性技术锅炉故障分析*

为预测和判断锅炉故障的发生,完善锅炉故障检测技术,基于锅炉运转具有非线性特点,提出将非线性评价指标应用于锅炉故障诊断。研究特征信号的非线性特性,通过确定延迟时间和嵌入维数来重构相空间;采用混沌分形理论研究非线性评价指标;提取最大Lyapunov指数和关联维数,并为收集的每种特征信号选择最合适的非线性指标。结果表明:蒸汽压力的非线性特征指标应选择关联维数,烟气温度1、烟气温度2、水管温度1和水管温度2的非线性特征指标应当选择最大Lyapunov指数。     

聚合氯化铝-腐殖酸(PACl-HA)絮体的物理与分形特征研究

采用低温急速冷冻-真空干燥技术制备了PACl-HA絮体的粉末样品,研究了这些样品的物理与分形特征.结果表明,PACl-HA絮体具有无定形结构,主要组成元素为C、O、Al,所含特征官能团保留了絮体组成原料的一些特征;絮体的BET比表面积为130～161 m²·g^-1,BJH累积吸附孔体积为0.38～0.52 cm³·g^-1,BJH脱附平均孔径为7.7～9.6nm,PSD峰值对应孔径8.4～11.2nm.PACl-HA絮体具有自相似性的粗糙表面,呈现多尺度分形特征;图象法和N₂吸附/脱附等温线法确定的表面分形维数Ds分别为2.03～2.26、2.24～2.37,前者的分形尺度大约处于23～390nm之间,主要属于絮体外表面尺度,而后者的分形特征尺度区间的下限大约为0.2nm,属于孔表面尺度;另外,对同一絮体,N₂吸附法和脱附法确定的孔表面分形维数不同.热力学模型计算出的D_s远大于3,与Sahouli等的研究不符.     

长短桩复合地基承载力发挥系数取值研究

根据水泥土长短桩复合地基试验结果,得到了考虑荷载水平的水泥土长短桩复合地基承载力计算公式。然后,考虑复合地基中桩体、桩间土和复合地基沉降量之间的相互关系,利用现场载荷试验成果,对单桩复合地基和长短桩复合地基的桩间土承载力发挥系数和合理的s/b取值范围进行了对比研究,得到了长短桩复合地基桩间土承载力发挥系数的计算方法。结果表明:长短桩复合地基桩体先于桩间土出现破坏,桩体极限荷载点对应的复合地基s/b值为s/b的上限;当垫层模量Ec为100M Pa时,长短桩复合地基s/b上限为0.0034,对应的桩间土承载力发挥系数为0.29。     

基于仿真的高速公路紧急事件交通流特征研究

研究高速公路紧急事件下的交通流特征,对于减少高速公路拥挤、降低二次事故、提高通行能力有重要的作用。由于高速公路紧急事件具有偶然性、不可预测性的特点,在实际调研中往往难以及时捕捉到交通事件的相应信息,导致源数据不足进而影响研究的进行。本文通过微观仿真手段,结合实地调研获得紧急状态下车辆运行参数,在AIMSUN仿真环境下加载紧急事件,建立了高速公路微观路段的仿真模型。并将路段平均车速、密度、最大排队长度等作为指标,定昔计算紧急事件下各种交通参数的变化规律。最后与调研结果进行了对比,表明仿真结果与实际情况较为一致。     

粉尘危害事件调查分析

在国内外粉尘危害事件频发的背景下,本文通过系统收集国内外报道的典型粉尘危害事件,探讨了粉尘危害事件的基本特征,并从政府、企业和技术发展3个层面对造成这些粉尘危害事件的成因进行分析。     

The effect of alkyl chain length on the degradation of alkylimidazolium- and pyridinium-type ionic liquids in a Fenton-like system

Background, aim, and scope  Ionic liquids are regarded as essentially “green” chemicals because of their insignificant vapor pressure and, hence, are a good alternative to the emissions of toxic conventional volatile solvents. Not only because of their attractive industrial applications, but also due to their very high stability, ionic liquids could soon become persistent contaminants of technological wastewaters and, moreover, break through into natural waters following classical treatment systems. The removal of harmful organic pollutants has forced the development of new methodologies known as advanced oxidation processes (AOPs). Among them, the Fenton and Fenton-like reactions are usually modified by the use of a higher hydrogen peroxide concentration and through different catalysts. The aim of this study was to assess the effect of hydrogen peroxide concentration on degradation rates in a Fenton-like system of alkylimidazolium ionic liquids with alkyl chains of varying length and 3-methyl-N-butylpyridinium chloride. Materials and methods  The ionic liquids were oxidized in dilute aqueous solution in the presence of two different concentrations of hydrogen peroxide. All reactions were performed in the dark to prevent photoreduction of Fe(III). The concentrations of ionic liquids during the process were monitored with high-performance liquid chromatography. Preliminary degradation pathways were studied with the aid of ¹H NMR. Results  Degradation of ionic liquids in this system was quite effective. Increasing the H₂O₂ concentration from 100 to 400 mM improved ionic liquid degradation from 57–84% to 87–100% after 60 min reaction time. Resistance to degradation was weaker, the shorter the alkyl chain. Discussion  The compound omimCl was more resistant to oxidation then other compounds, which suggests that the oxidation rates of imidazolium ionic liquids by OH· are structure-dependent and are correlated with the n-alkyl chain length substituted at the N-1-position. The level of degradation was dependent on the type of head group. Replacing the imidazolium head group with pyridinium increased resistance to degradation. Nonetheless, lengthening the alkyl chain from four to eight carbons lowered the rate of ionic liquid degradation to a greater extent than changing the head group from imidazolium to pyridinium. 1H-NMR spectra show, in the first stage of degradation, that it is likely that radical attack is nonspecific, with any one of the carbon atoms in the ring and the n-alkyl chain being susceptible to attack. Conclusions  The proposed method has proven to be an efficient and reliable method for the degradation of imidazolium ionic liquids by a Fenton-like reagent deteriorated with lengthening n-alkyl substituents and by replacing the imidazolium head group with pyridinium. The enhanced resistance of 1-butyl-3-methylpyridinium chloride when the resistance of imidazolium ionic liquids decreases with increasing H₂O₂ concentration is probably indicative of a change in the degradation mechanism in a vigorous Fenton-like system. H-NMR spectra showed, in the first stage of degradation, that radical attack is nonspecific, with any one of the carbon atoms in the ring and the n-alkyl chain being susceptible to attack. Recommendations and perspectives  Since ionic liquids are now one of the most promising alternative chemicals of the future, the degradation and waste management studies should be integrated into a general development research of these chemicals. In the case of imidazolium and pyridinium ionic liquids that are known to be resistant to bio- or thermal degradation, studies in the field of AOPs should assist the future structural design as well as tailor the technological process of these chemicals     

火电厂SCR烟气脱硝催化剂特性及其应用

SCR工艺是火电厂的主流烟气脱硝技术,催化剂是SCR脱硝工艺的核心。通过对不同型式催化剂特性及其应用的对比分析,得出了蜂窝式催化剂综合性能较优的结论,并对不同烟气条件下的催化剂选择提出了建议.