土霉素对SBR系统细菌的抑制效应与机制研究

基于SBR系统,从脱氮过程、化学需氧量(COD)的去除过程、胞外聚合物(EPS)的总量变化过程、比呼吸速率(SOUR)的变化过程及微生物群落的变化等多个角度出发,较系统地研究了不同浓度土霉素对SBR系统的冲击作用.结果表明,由于土霉素(OTC)的作用,系统氨氮去除率从空白对照组的99.0%分别下降至77.2%(OTC 1 mg·L~(-1))、47.4%(OTC 5 mg·L~(-1))及10.0%(OTC 10 mg·L~(-1)).此外,高浓度土霉素(10mg·L~(-1))引起EPS分泌量和异养菌SOUR分别下降至空白组的44.3%和41.2%.由高通量分析可得,由于高浓度土霉素(5 mg·L~(-1)以上)的作用,活性污泥中微生物的多样性显著下降,且微生物的群落结构也发生显著变化.属层面的分析可得,高浓度土霉素(5 mg·L~(-1)以上)反应器中的部分氨氧化菌,如Nitrospira和Nitrosomonas均受到了抑制.     

抗生素废水的铁屑微电解预处理研究

研究了采用铁屑微电解法预处理抗生素废水.在进水COD质量浓度为6.2 g/L时,试验结果表明,经微电解处理后的废水,COD和色度的去除率分别达到68.3%和79.3%,BOD5/COD从0.306提高到0.56,废水的可生化性得到显著提高.通过正交试验考察pH、反应时间及铁屑用量对处理效果的影响,并对各因素作了单因素影响试验,确定了最佳工艺条件.     

不同条件下高炉渣吸附水中无机磷的研究

高炉渣(BFS)是在冶炼生铁过程中产生的固体废弃物,开展高炉渣的资源化研究具有重要意义.为了对水淬高炉渣净化含磷污水的应用提供理论依据,采取等温吸附的实验方法,比较了不同水淬炉渣的吸附磷效果,研究了不同pH和不同温度下水淬炉渣吸附磷的特点,结果如下:利用Langmuir等温吸附方程炉渣吸附磷的过程进行拟合,其相关系数均能达到显著水平.炉渣的碱度越高,吸附磷的效果越好;炉渣对磷的吸附能力随溶液pH的增加而降低,且初始为酸性(pH=2、4)的溶液在吸附达到平衡后pH有所上升,而初始为碱性的溶液(pH=10、12)在吸附达到平衡后pH有所下降;炉渣对磷的吸附是一个自发放热过程.     

A2/O工艺中的反硝化除磷

A2/O工艺是一种最简单的同步脱氮除磷工艺,但由于其系统中固有的基质竞争和污泥龄等矛盾,在实际应用中特别是处理低C/N比污水时脱氮除磷效率较低.反硝化除磷工艺作为近年来颇受关注的污水生物处理新技术.由于在脱氮除磷过程中可以在碳源利用上耦合,可从一定程度上缓解A2/O工艺中的基质竞争矛盾,使得其在处理低C/N比污水时也能实现较高的脱氮除磷效率.就反硝化除磷的技术原理,结合其在A2/O工艺中的最新研究成果及其控制策略,对A2/O工艺中的反硝化除磷的实现、维持及影响因素进行了分析和探讨,并对其发展方向进行了展望.     

In field arsenic removal from natural water by zero-valent iron assisted by solar radiation

An in situ arsenic removal method applicable to highly contaminated water is presented. The method is based in the use of steel wool, lemon juice and solar radiation. The method was evaluated using water from the Camarones River, Atacama Desert in northern Chile, in which the arsenic concentration ranges between 1000 and 1300 μg L⁻¹. Response surface method analysis was used to optimize the amount of zero-valent iron (steel wool) and the citrate concentration (lemon juice) to be used. The optimal conditions when using solar radiation to remove arsenic from natural water from the Camarones river are: 1.3 g L⁻¹ of steel wool and one drop (ca. 0.04 mL) of lemon juice. Under these conditions, removal percentages are higher than 99.5% and the final arsenic concentration is below 10 μg L⁻¹. This highly effective arsenic removal method is easy to use and inexpensive to implement.     

聚硅酸氯化铝处理皂素废水的研究

制备了聚硅酸氯化铝(PASC)絮凝剂,并用其进行了皂素废水处理实验。考察了絮凝剂投加量、pH值、搅拌速度对COD和浊度去除率的影响。结果表明,当絮凝剂投加量为9～13.5 mg/L、pH值5～7、搅拌速度150～250 r/min时,COD和浊度去除效果较好。最佳工艺条件为：絮凝剂投加量11.25 mg/L、pH值6、搅拌速度200 r/min。此时,COD去除率为93.7％,浊度去除率为97.5％。PASC的絮凝性能明显优于PAC。     

Impact of Bioaugmentation with a Consortium of Bacteria on the Remediation of Wastewater-Containing Hydrocarbons (5 pp)

Goals, Scope and Background It has been observed that hydrocarbon treated wastewaters still contain high COD and a number of intermediates. This suggests that the required catabolic gene pool for further degradation might be absent in the system or, that its titer value is not significant enough. By providing the desired catabolic potential, the overall efficiency of the treatment system can be improved. This study aims to demonstrate this concept by bioaugmentation of a lab-scale reactor treating refinery wastewater with a consortium having the capacity to complement the alkB genotype to the available microbial population. Methods Two reactors were set up using activated biomass collected from a refinery treatment plant and operated at a continuous mode for a period of 8 weeks. The feed to both reactors was kept constant. Crude oil was spiked regularly. One reactor was bioaugmented with a consortium previously described for crude oil spill remediation. The efficiency of the bioaugmented reactor was demonstrated by reduced COD. The changes in the microbial population over a period of time were analyzed by RAPD. Catabolic activity of the biomass in both reactors was monitored by PCR. The presence of the catabolic loci was confirmed by Southern Hybridization. Results and Discussion 52.2% removal of COD was observed in the bioaugmented reactor while only 15.1% reduction of COD was observed in the reactor without bioaugmentation. The change in microbial population can be seen from the 4th week, which also corresponds to improved catabolic activity. The presence of the bedA locus was seen in all samples, which indicates the presence of aromatic degraders, but the appearance of the alkB locus, from the 6th week onwards, which was observed only in the samples from the bioaugmented reactor. The results suggest that the gene pool of the bioaugmented reactor has catabolic loci that can degrade accumulated intermediates, thus improving the efficiency of the system. Conclusions In this study, improvement of efficiency of bioremediation was demonstrated by addition of catabolic loci that are responsible for degradation. Bioaugmentation was carried out in biomass that was collected from an ETP (effluent treatment plant) treating hydrocarbon containing wastewater to study the strategies for improvement of the treatment system. Biostimulation, only marginally improved the efficiency, when compared to bioaugmentation. The improved efficiency was demonstrated by COD removal. The presence of the alkB locus suggests the importance of a catabolic gene pool that acts on accumulated intermediates. It is well documented that straight chain aliphatics and intermediates of aromatic compounds after ring cleavage, accumulate in refinery wastewater systems, thereby hindering further degradation of the wastewater. Supplementation of a catabolic gene pool that treats the lower pathway compounds and alkanes will improve the overall efficiency. In this study, results suggest that the alkB locus can also be used to monitor the degradative mode of the activated biomass. Recommendations and Perspective . Pollution from petroleum and petroleum products around the globe are known to have grave consequences on the environment. Bioremediation, using activated sludge, is one option for the treatment of such wastes. Effluent treatment plants are usually unable to completely degrade the wastewater being treated in the biological unit (the aerator chambers). The efficiency of degradation can be improved by biostimulation and bioaugmentation. This study demonstrates the improved efficiency of a treatment system for wastewater containing hydrocarbons by bioaugmentation of a consortium that supports degradation. Further experiments on a pilot scale are recommended to assess the use of bioaugmentation on a large scale. The use of molecular tools, like DNA probes for alkB, to monitor the system also needs to be explored.     

Heavy metals in untreated/treated urban effluent and sludge from a biological wastewater treatment plant

Background, Aim and Scope

The presence of heavy metals in wastewater is one of the main causes of water and soil pollution. The aim of the present study was to investigate the removal of Cd, Cu, Pb, Hg, Mn, Cr and Zn in urban effluent by a biological wastewater treatment, as well as to quantify the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn, Tl, V and Zn in dewatering sludge from the Biological Wastewater Treatment Plant to Ribeirão Preto (RP-BWTP), Brazil.

Materials and Methods

Concentrations of Cd, Cr, Cu, Mn and Pb in wastewater and those of Ni in sludge were determined by atomic absorption spectrophotometry with graphite furnace atomization. Mercury concentrations in wastewater were measured by hydride generation atomic spectrophotometry, and Zn levels were determined by atomic absorption spectrophotometry using acetylene flame. In sludge, the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Sn, Tl, V and Zn were determined by inductively coupled plasma-mass spectrometry.

Results

The percentages of removal efficiency (RE) were the following: Hg 61.5%, Cd 60.0%, Zn 44.9%, Cu 44.2%, PB 39.7%, Cr 16,5% and Mn 10.4%. In turn, the mean concentrations (mg/kg) of metals in dewatering sludge followed this increasing order: Tl (<0.03), Hg (0.31), Be (0.43), As (1.14), Cd (1.34), V (59.2), Pb (132.1), Sn (166.1), Cr (195.0), Mn (208.1), Ni (239.4), Cu (391.7), Zn (864.4) and Fe (20537).

Discussion

The relationship between metal levels in untreated wastewater, as well as the removal efficiency are in agreement with previous data from various investigators, It is important to note that metal removal efficiency is not only affected by metal ion species and concentration, but also by other conditions such as operating parameters, physical, chemical, and biological factors.

Conclusions

Metal values recorded for treated wastewater and sludge were within the maximum permitted levels established by the Environmental Sanitation Company (CETESB), São Paulo, Brazil.

Recommendations

There is an urgent need for the authorities who are responsible for legislation on sludge uses in agriculture of establishing safety levels for As, Be, Hg, Sn, Tl and V.

Perspectives

According to the current metal levels, RP-BWTP sludge might be used for agriculture purposes. However, for an environmentally safe use of sewage sludge, further studies including systematic monitoring are recommended. Annual metal concentrations and predicted variations of those elements in the sludge should be monitored.

     

生物滤池对气相与液相中污染物质的净化

通过实验室研究探讨了生物滤池同时处理废水和废气的可行性。试验结果表明：在２５℃－３７℃条件下,甲苯废气的流量为９０Ｌ／ｈ,甲苯浓度为５００ｍｇ／ｍ＾３;废水的流量为０．４Ｌ／ｈ,ＣＯＤｃｒ浓度为４００－７５０ｍｇ／Ｌ,甲苯与ＣＯＤｃｒ的去除率分别是７０％－７２％和８６％－８９％。     

氯化二丁基锡对小鼠外周血液中睾丸酮和雌二醇含量的影响

用放射免疫法分别测定了DBTCl对妊娠d6雌小鼠和成年雄小鼠外周血液中雌二醇和睾丸酮水平的影响.每天按小鼠体重一次腹腔注射0.025～0.400μg/kgd-1DBTCl,共染毒7d.实验条件为(22±2)℃和光暗=12h12h.结果表明,处理组睾丸酮和雌二醇的含量随处理剂量的增加而增加,当w（DBTCl）≥0.05μg/kg时,二者呈明显的剂量-效应关系.雌二醇含量的增加比睾丸酮更为显著CK雄性小鼠睾丸酮浓度为（2.88±0.72）ng/mL,在0.40μg/kg剂量组达到(9.95±2.5)μg/mL时,约为CK的3.5倍;而CK和0.40ng/kg剂量组妊娠小鼠雌二醇浓度分别为(30.32±5.43)ng/mL和(287.57±51.13)ng/mL,相差约9.5倍.文中还就DBTCl对小鼠血液中激素含量的影响机理进行了初步探讨.图1表2参20