中国污染场地修复的研究进展、问题与展望

随着城市化和产业转移进程的加快,我国城镇工业企业搬迁或遗留的污染场地数量与日俱增,亟须开展污染场地治理与修复工作,以保障人居环境安全、国民健康和社会稳定.综述了我国污染场地及其产生、状态和风险,污染场地管理、修复技术及工程实践进展,污染场地管理和修复的主要问题,场地污染防治与修复政策、技术和融资机制需求,旨在推进污染场...     

Advantages and risks of using steel slag in preparing composts from raw organic waste

It had been reported that iron and manganese oxides in steel slag enhanced the production of humic acid (HA) from low-molecular-weight compounds, such as phenolic acids, amino acids, and saccharides. In the present study, this function of steel slag was applied to the composting of raw organic wastes (ROWs). The degree of humification of HAs is an important factor in evaluating compost quality. Thus, HAs were extracted from the prepared composts and the humification parameters were determined, in terms of elemental compositions, acidic functional group contents, molecular weights, spectroscopic parameters from UV–vis absorption and ¹³C NMR spectra. The timing for adding steel slag affected the degree of humification of HAs in the composts. The weight average molecular weight of a HA when slag was added initially (29 kDa) was significantly higher than when slag was added after elevating the temperature of the compost pile (17–18 kDa). These results show that ROWs are decomposed to low-molecular-weight compounds after the pile temperature is elevated and the presence of slag enhances the polycondensation of these compounds to produce HAs with a higher degree of humification. Because the slag used in the present study contained several-tens ng g^?1 to several μg g^?1 of toxic elements (B, Cu, Cr, and Zn), leaching tests for these elements from the prepared composts were carried out. Levels for leaching boron from composts prepared by adding slag (0.2–0.4 mg L^?1) were obviously higher than the corresponding levels without slag (0.05 mg L^?1).     

Evidence of new particle formation during post monsoon season over a high-altitude site of the Western Ghats,India

The formation of ultrafine particles, their growth, and associated characteristic features has been studied during new particle formation events over a high-altitude station of the Western Ghats during the 2014 post-monsoon season. Most of the events were observed during noon time where particle bursts in the nucleation-mode size range from 5 to 25 nm followed by sustained growth in size. This phenomenon persists for ～4–8 h with a growth rate of 1–2 nm h^–1. Peak concentrations of nucleation-mode particles during the event generally vary from 2300 to 5000 cm^–3. The mean growth rate is 1.4 ± 0.42 nm h^–1, particle formation rate is 1.14 ± 0.22 cm^–3 s^–1, coagulation sink is 0.35 ± 0.22 cm^–3 s^–1, and condensational sink is 15.4 ± 2.6?×?10^–3 s^–1. All these values are comparable with earlier results from Indian region. Comparison of size-segregated particle number concentration during days of new particle formation events and those without new particle formation were carried out showing a distinct variation in nucleation and Aitken mode with least variability associated with the accumulation mode.     

Optimization-Based Atmospheric Plume Source Identification

This work applies optimization and an Eulerian inversion approach presented by Bagtzoglou and Baun in 2005 in order to reconstruct contaminant plume time histories and to identify the likely source of atmospheric contamination using data from a real test site for the first time. Present-day distribution of an atmospheric contaminant plume as well as data points reflecting the plume history allow the reconstruction and provide the plume velocity, distribution, and probable source. The method was tested to a hypothetical case and with data from the Forest Atmosphere Transfer and Storage (FACTS) experiment in the Duke experimental forest site. In the scenarios presented herein, as well as in numerous cases tested for verification purposes, the model conserved mass, successfully located the peak of the plume, and managed to capture the motion of the plume well but underestimated the contaminant peak.     

竹制填料生物接触氧化工艺处理污染河水简

针对受污染的湖溪河水质特征,以传统弹性塑料填料做对比,研究以竹球和竹丝为填料的生物接触氧化工艺,考察填料的挂膜时间、生物量和污水处理效果;确定连续曝气和间歇曝气时反应器的最优运行工况：连续曝气时为HRT=7.5 h,DO=3 mg/L;间歇曝气时为厌氧1.2 h、好氧6.3 h交替运行。实验结果表明,与弹性塑料填料相比,竹制填料挂膜速度快,竹球填料的水处理效果最好;连续曝气最优工况下竹球填料反应器中COD、TN、NH₃-N和TP的平均去除率分别为66.7%、47.9%、57.1%和30.6%;间歇曝气最优工况下竹球填料反应器中COD、TN、NH₃-N和TP的平均去除率分别64.08%、39.95%、60.7%和54.68%;竹制填料可替代传统的塑料填料作为生物接触氧化工艺的载体填料。     

中和共沉淀—铁氧体法处理含镍、铬废水的实验研究

利用中和共沉淀—铁氧体法处理甘肃某稀有金属生产企业产生的含镍、铬废水,同时对该废水的处理工艺条件进行了实验研究。经测定,废水中Ni 2+质量浓度为50mg/L,Cr(Ⅲ)质量浓度为87mg/L。通过实验得到处理工艺的最佳条件:投料摩尔比(Fe2+/(Ni 2++Cr2O2-7))为9,pH=9,温度为70℃。出水中镍、铬均可达到《污水综合排放标准》(GB 8978—1996)中第一类污染物最高允许排放浓度的要求,为中和共沉淀—铁氧体法处理混合重金属废水的工艺条件研究提供了参考。     

某典型化工污染场地土壤修复方案研究

以典型化工污染场地为研究对象,构建适合该场地的修复技术筛选体系,筛选最佳修复方法。根据特征污染筛选结果、场地修复目标及业主需求等因素,通过室内模拟实验、施工现场微调等方法,确定污染场地最优修复方案。结果表明,作为Cd、苯并[a]芘复合污染场地,根据筛选体系结合Topsis法进行评估,确定场地修复技术为异位化学淋洗。运用响应曲面法,采用BoxBehnken设计多因素实验进行室内模拟,确定最佳修复条件。采用0.6mol/L柠檬酸与20g/Lβ-环糊精进行复配的淋洗剂,在pH=3.0、淋洗温度35.00℃、液固比(淋洗剂与土壤的体积质量比)6.00mL/g、搅拌强度320.00r/min下,淋洗4次,每次淋洗3.4h,对某化工污染场地进行修复,修复后土壤中Cd、苯并[a]芘的去除量分别为69.88、39.20mg/kg,去除率分别达80.14%、70.50%,达到预期修复目标。     

Steel slags in a landfill top cover – Experiences from a full-scale experiment

A full scale field study has been carried out in order to test and evaluate the use of slags from high-alloy steel production as the construction materials for a final cover of an old municipal landfill. Five test areas were built using different slag mixtures within the barrier layer (liner). The cover consisted of a foundation layer, a liner with a thickness of 0.7 m, a drainage layer of 0.3 m, a protection layer of 1.5 m and a vegetation layer of 0.25 m. The infiltration varied depending on the cover design used, mainly the liner recipe but also over time and was related to seasons and precipitation intensity. The test areas with liners composed of 50% electric arc furnace (EAF) slag and 50% cementitious ladle slag (LS) on a weight basis and with a proper consistence of the protection layer were found to meet the Swedish infiltration criteria of ?50 l (m² a)^?1 for final covers for landfills for non-hazardous waste: the cumulative infiltration rates to date were 44, 19 and 0.4 l (m² a)^?1 for A1, A4 and A5, respectively. Compared to the precipitation, the portion of leachate was always lower after the summer despite high precipitation from June to August. The main reason for this is evapotranspiration but also the fact that the time delay in the leachate formation following a precipitation event has a stronger effect during the shorter summer sampling periods than the long winter periods. Conventional techniques and equipment can be used but close cooperation between all involved partners is crucial in order to achieve the required performance of the cover. This includes planning, method and equipment testing and quality assurance.     

抗铬菌株的筛选鉴定及其生物学特性和吸附特性

利用微生物分离纯化技术,在培养基中加入不同浓度的Cr3+、Cr6+,经过长时间驯化,从污染土壤中筛选出2株对Cr具有较高抗性的菌株(A和B),对其进行了形态、生理生化特性及分子生物学鉴定,并研究了其最佳生长条件及对Cr3+的生物吸附规律。结果表明,菌株A和B分别为蜡状芽孢杆菌(Bacillus cereus)和米根霉菌(Rhizopus oryzae)。菌株A和B的最适生长pH值均为7,最适生长温度均为30℃,最佳装液量为80~100 mL(250 mL摇瓶)。在培养时间一定时,随着Cr3+浓度的增加,菌株对Cr3+的吸附率减少,而生物吸附量则逐渐增大;在Cr3+浓度一定时,随着培养时间的延长,菌体对Cr3+的吸附率呈现出先增加后减少的趋势,这与生物吸附量的变化趋势基本一致。在Cr3+浓度为100 mg/L时,菌株A和B对Cr3+的吸附率达到最大,分别为51.47%和46.36%。     

鼠李糖脂洗脱氯丹和灭蚁灵污染场地土壤的工艺参数

优化了鼠李糖脂洗脱氯丹、灭蚁灵污染土壤的工艺条件,为开展有机氯农药污染场地土壤洗脱修复工程实践提供科学依据和技术参数。实验结果表明,随着洗脱剂———鼠李糖脂浓度的增加,氯丹和灭蚁灵的洗脱量呈现先增加后降低的趋势;洗脱时间和液固比对洗脱效果的影响趋势与浓度相同;在0~120 r/min范围内,氯丹和灭蚁灵洗脱量随着搅拌速度的增加而增大,80、120和200 r/min的洗脱量间差异不显著;单次洗脱量随洗脱次数的增加而降低,累计洗脱量则逐渐增大。综上所述,氯丹、灭蚁灵污染场地土壤鼠李糖脂洗脱的适宜工艺参数为鼠李糖浓度10 mmol/L,搅拌速度80 r/min,固液比1∶10,洗脱时间20 min,洗脱3次。