成都市及周边地区严重臭氧污染过程成因分析

结合天气形势,地面观测资料和WRF-CMAQ模式,分析了2017年7月8~15日成都市一次罕见持续O₃污染过程的特征及成因,量化了各个物理化学过程对此次污染过程的相对贡献,并通过敏感性实验分析了四川盆地内O₃及其前体物的区域传输和本地光化学反应对此次污染过程的影响.结果表明,此次O₃持续污染过程主要是因为四川盆地内盛行偏东风,导致盆地东部城市群的O₃及其前体物经区域输送到成都及周边地区,加之成都市出现小风、气温升高等气象条件进而形成,属于典型的传输性爆发污染.持续污染形成的主要物理化学机制体现为日间气相化学过程贡献为稳定的正值,加之输送过程贡献出现爆发式升高,进而导致近地面O₃小时净增量迅速上升且高达50μg/（m³·h）,随之O₃浓度迅速响应,产生爆发式增长.此外,敏感性实验结果显示此次成都市O₃持续污染的形成受区域输送影响较受本地光化学反应影响更为明显.O₃污染爆发前上游地区高浓度O₃及其前体物沿流场输送并在成都及周边地区不断积累,导致日间O₃浓度不断升高.     

漓江流域δD和δ18O对蒸发的指示作用

以漓江流域为例查明不同水体之间氢氧稳定同位素组成特征,并探讨氢氧稳定同位素对漓江流域的蒸发过程指示作用.结果表明：流域内不同水体之间,氢氧稳定同位素表现出不同的组成特征,地表水和地下水,在丰水期δD值和δ¹⁸O值要比枯水期更容易富集,地下水的δD值和δ¹⁸O值分布范围较地表水小;随着水温的升高,δ¹⁸O的变化趋势比d-excess明显.从漓江上游到下游高程逐渐下降,河水线的斜率和截距也在逐渐减小,其中漓江下游河水线的斜率和截距要低于当地大气降水线,表明下游受到蒸发作用较强烈;地下河水线、地表河水线在一定程度上偏离当地大气降水线,但偏离程度较小,表明三者之间有很好的水力联系.受温度和湿度的共同影响,漓江干流丰水期河水的蒸发量占最初水体总量的0.7%~9.1%,枯水期河水的蒸发量占最初水体总量的2.6%~9.7%,丰水期的蒸发比例低于枯水期,从上游到下游蒸发比例在逐渐上升.研究区蒸发量估算值为959.40mm,与多年实测值少43.11mm,相对误差4.70%.氢氧稳定同位素对研究区降水、地表水、地下水之间的转换规律具有重要的实际意义,在今后的漓江流域水文研究中有着更加广阔的空间.     

大辽河沉积物中微塑料的污染特征

以大辽河为研究对象,选取8个典型区域的沉积物,采用密度浮选法,结合体视显微镜及μ-FTIR,进行大辽河沉积物中微塑料的组成及分布特征研究.结果表明,大辽河沉积物微塑料平均丰度为（66.67±79.93）个/kg;其中位于鞍山海城市的DL5丰度最高,为（193.33±172.43）个/kg,辽阳县柳壕镇的DL6丰度最低,为（20.00±34.64）个/kg;微塑料颜色以白色、黑色、黄色为主（83.75%）,形状以纤维、薄膜、碎片为主（91.25%）,粒径以（1000~2000）μm为主（33.75%）.通过红外光谱分析可得出,大辽河沉积物中薄膜类微塑料的主要成分是聚酰胺（PA）、聚丙烯（PP）和聚乙烯（PE）,碎片类的主要成分是聚乙烯（PE）和聚丙烯（PP）,泡沫类和颗粒类的主要成分是聚苯乙烯（PS）,纤维类的主要成分是人造丝（RY）及聚对苯二甲酸乙二醇酯（PET）.总体上,该研究区域沉积物中微塑料的丰度处于中等偏低水平.本研究可为我国淡水河流沉积物中微塑料的污染分布研究提供基础科学数据.     

离子液体吸收废印刷线路板热拆解过程中挥发性有机物——基于COSMO-RS模型

模拟废印刷线路板（WPCB）的热拆解过程,分析热拆解过程中的挥发性有机物（VOCs）组分;利用真实溶剂似导体屏蔽（COSMO-RS）模型对浓度较高的污染物进行量子力学模拟,研究离子液体（ILs）组成单元对目标污染物溶解度的影响差异,分析溶解过程中主导分子间作用力类型,确定优选吸收剂;测定不同溶剂进行溶解性,验证模型适用性.结果表明：①乙酸乙酯和环戊酮是浓度较高的VOCs组分,在240和250℃时浓度分别为43.1,153mg/m³和105,252mg/m³,质量百分比总和分别为76.3%和67.3%.②高表面屏蔽电荷密度分布峰、长烷基链阴阳离子和亲电基团的存在可提高乙酸乙酯和环戊酮在ILs中的溶解度.双三氟甲磺酰基亚胺盐（NTf₂^-）类ILs是一类优良吸收剂.静电力和范德华力对溶解过程起主导作用.③COSMO-RS模型可定性和半定量用于预测乙酸乙酯和环戊酮的溶解度.     

色氨酸对生物成因铁硫酸盐次生矿物形成的影响

采用氧化亚铁硫杆菌催化合成铁硫酸盐次生矿物,研究不同L-色氨酸添加浓度对矿物合成体系pH、氧化还原电位（ORP）、Fe²⁺氧化率、总Fe沉淀率,以及次生矿物产量、化学组成及矿物相的影响.结果表明,随着体系色氨酸浓度的增加,pH降低幅度越小,ORP上升越不明显.色氨酸对铁硫酸盐次生矿物合成的影响依赖于其浓度,当色氨酸浓度低于1.67 g·L^-1时,色氨酸对铁硫酸盐次生矿物的形成起促进作用,表现为总Fe沉淀率及矿物产量随着色氨酸浓度升高而增加.而当色氨酸浓度升高至6.67 g·L^-1时,Fe²⁺氧化率、总Fe沉淀率和矿物产量远低于对照组,表明高浓度色氨酸会抑制铁硫酸盐次生矿物的形成.次生矿物内Fe/S比介于施氏矿物和黄钾铁矾的理论值之间,表明不同合成体系所得次生矿物均为黄钾铁矾和施氏矿物的混合物.矿物学特征分析表明,随着色氨酸浓度的升高,矿物的合成表现为黄钾铁矾向施氏矿物转移.     

Fas/FasL途径在氟暴露致PC12细胞凋亡中的作用

为了探讨Fas/FasL途径在氟暴露致PC12细胞凋亡中的作用及其机制,采用含20、40、80、160mg/L NaF培养液处理PC12细胞.结果表明,所有剂量NaF处理12、24、36、48h,PC12细胞活性升高;上述不同剂量NaF处理24h后,与对照组比,PC12细胞的活性氧水平、细胞凋亡率、细胞内Fas/FasL信号转导通路Fas和FasL、Caspase8、FADD、Caspase3基因和蛋白表达水平均呈显著上升（P < 0.05）,而Bid基因和蛋白表达水平显著下降（P < 0.05）,且呈氟暴露剂量依赖性.结果提示Fas/FasL途径在氟暴露致PC12细胞凋亡中起重要作用,其中FADD可能是Fas/FasL凋亡途径中的重要靶分子.     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

Kitchen waste valorization through a mild-temperature pretreatment to enhance biogas production and fermentability: Kinetics study in mesophilic and thermophilic regimen

Biowaste valorization through anaerobic digestion is an attractive option to achieve both climate protection goals and renewable energy production. In this paper, a complete set of batch trials was carried out on kitchen waste to investigate the effects of mild thermal pretreatment, temperature regimen and substrate/inoculum ratio. Thermal pretreatment was effective in the solubilisation of macromolecular fractions, particularly carbohydrates. The ability of the theoretical methodologies in estimating hydrogen and methane yields of complex substrates was evaluated by comparing the experimental results with the theoretical values. Despite the single batch configuration, a significant initial hydrogen production was observed, prior to methane yield. Main pretreatment effect was the gain in hydrogen production; the extent was highly variable according to the other parameters values. High hydrogen yields, up to 113 mL H2/g VSfed, were related to the prompt transformation of soluble sugars. Thermophilic regimen resulted, as expected, in faster digestions (up to 78 mL CH₄/gVS/day) and sorted out pH inhibition. The relatively low methane yields (342–398 mL CH₄/g VS_fed) were the result of the consistent lignocellulosic content and low lipid content. Thermal pretreatment proved to be a promising option for the enhancement of hydrogen production in food waste dark fermentation.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

Recent advances in catalytic decomposition of ozone

Ozone (O₃), as a harmful air pollutant, has been of wide concern. Safe, efficient, and economical O₃ removal methods urgently need to be developed. Catalytic decomposition is the most promising method for O₃ removal, especially at room temperature or even subzero temperatures. Great efforts have been made to develop high-efficiency catalysts for O₃ decomposition that can operate at low temperatures, high space velocity and high humidity. First, this review describes the general reaction mechanism of O₃ decomposition on noble metal and transition metal oxide catalysts. Then, progress on the O₃ decomposition performance of various catalysts in the past 30 years is summarized in detail. The main focus is the O₃ decomposition performance of manganese oxides, which are divided into supported manganese oxides and non-supported manganese oxides. Methods to improve the activity, stability, and humidity resistance of manganese oxide catalysts for O₃ decomposition are also summarized. The deactivation mechanisms of manganese oxides under dry and humid conditions are discussed. The O₃ decomposition performance of monolithic catalysts is also summarized from the perspective of industrial applications. Finally, the future development directions and prospects of O₃ catalytic decomposition technology are put forward.