长治市沙尘天气污染特征及传输路径解析

以2018年3次沙尘天气为研究对象,分析了PM_2.5和PM₁₀浓度、水溶性离子组分、气象条件和气溶胶光学特征,研究了长治市沙尘天气的典型污染特征和传输路径.结果表明：长治市2018年共8d为受沙尘天气影响日,其中4月份最多（5d）,这与春季大气环流调整,冷暖空气活动频繁有关.沙尘污染发生前一般受西方或西北方冷空气影响,大气层结不稳定,大气环流转为经向环流,平均风速达4m/s以上;沙尘污染过程中PM_2.5/PM₁₀均低于0.3,环境空气中粗颗粒物占比较大,水溶性离子总浓度在PM_2.5中占比下降,Ca²⁺浓度为沙尘污染发生前的4倍以上.冬季沙尘为近地面扩散传输,春夏季沙尘为高空沉降传输,影响范围大,区域传输贡献明显.长治市沙尘重要潜在源区为蒙古国、哈萨克斯坦中部和新疆中北部的荒漠地区,传输路径主要为西北路径和正北路径,其中西北路径为哈萨克斯坦—新疆中北部—内蒙古西部—长治以及新疆中北部—内蒙古西部—长治两条路径,正北路径为蒙古国—内蒙古中部—山西北部—长治.     

纤维增强气凝胶复合材料高温结构转变及热稳定性研究

目的研究高温受热条件下纳米复合隔热材料的结构转变特征及热稳定性。方法采用扫描电镜、X射线衍射仪、红外光谱仪及热重仪等检测方法。结果纤维增强气凝胶材料从室温到650℃存在连续的质量损失,从室温到放热前,质量损失为1.66%;365℃开始出现放热,温度升至398℃时达到峰值,整个放热过程对应质量损失约为1.3%;从435℃放热结束开始到650℃的质量损失为1.46%。经过400℃热处理后,试样比表面积从268m~2/g增加到437m~2/g;当试样热处理温度达到600℃时,试样的比表面积明显随之降低至198m~2/g。结论 SiO_2气凝胶复合材料以无定形结构为主,存在少量的二氧化钛晶体。在400℃左右,SiO_2气凝胶结构中硅甲基Si—CH_3发生氧化,产生明显的放热峰,之后硅羟基Si—OH之间发生缩聚反应,使600℃热处理后气凝胶中Si—O—Si网络骨架强度有所提高。未处理的纤维增强气凝胶材料试样上气凝胶纳米颗粒构成的块体较为良好地包裹在玻璃纤维表面,而经过600℃的高温热处理1 h后,块体气凝胶脱离了光滑的纤维表面,气凝胶纳米粒子发生收缩,致使材料比表面积下降。     

油气田在役管道高后果区识别与完整性评价方法

根据油气管道建设与管理的相关标准与规范或导则,针对目前油气田在役管道,明确了其高后果区识别的划分及其在不同标准中的差异以及识别的原则和时间间隔,分别介绍了在管道的相关数据采集的基础上开展地质灾害和第三方破坏造成的管道风险评价方法,管道内外腐蚀的直接评价以及包括剩余强度、剩余寿命和材料在内的管道适用性评价方法,同时给出了这些评价工作所涉及到的相关内容项,对油田管道的完整性管理具有重要的指导作用和应用价值。     

旅游目的地网络空间结构及其复杂性研究——野三坡旅游地案例实证

复杂性是旅游目的地网络化发展的必然趋势,是认识旅游地网络空间结构与组织特征的重要研究手段。论文以河北省野三坡旅游地为例,通过构建旅游联系强度模型,建立旅游地空间网络,并运用TOP网络空间分析以及复杂网络理论,揭示旅游地网络空间结构与组织的复杂性特征。研究发现：1）旅游地网络具有空间集聚性,形成了以核心景区为中心,由中心城镇、乡村社区和特色园区共同构成的空间集聚单元,并体现出“邻近连接”与“择优连接”的双重特性;2）旅游地网络服从幂律分布,具有无标度网络特性;3）每个节点的前三名和前五名旅游联系强度网络（Top3和Top5网络）具有较小的平均路径长度、较大的集聚系数,呈现出典型的“小世界网络”特征;4）旅游地网络是典型的异配型网络,度-度呈负相关,而网络节点的集聚系数与其度值之间存在近似的倒数关系,因此具有层次性。     

Relationship between PM10 and PM2.5 levels in high-traffic area determined using path analysis and linear regression

The objective of this study was to determine the relationship between PM_(10) and PM_(2.5) levels as related to meteorological conditions and traffic flow using both a linear regression analysis and a path analysis. The Particulate matter(PM) samples were collected from Sukhumvit road, Bangkok, Thailand, at both open(104 samples) and covered(92 samples)areas along the road. Fifteen percent of all samples were separated before the statistical models were run and used for model validation. The results from the path analysis were more elaborate than those from the linear regression, thus indicating that meteorological conditions had a direct effect on the particulate levels and that the effects of traffic flow were more variable in open areas. The model also indicated that meteorological conditions had an indirect effect and that traffic flow had a direct effect on particulate levels in covered areas. The model validation results indicated that for open areas, the R~2 values were not very different between the path analysis and the linear regression model, but that the path analysis was more accurate than the linear regression model at very low PM concentrations. At high PM concentrations, the path analysis model also had a better fit than did the linear regression, so the predictions from the path analysis model were more accurate than those from the linear regression.     

Ecotoxicity evaluation of Cu- and Fe-CNT complexes based on the activity of bacterial bioluminescence and seed germination

The toxic effects of the composites of Fe~0 and Cu~0 with different percentages of CNTs were examined based on the activity of bacterial bioluminescence and seed germination. In terms of the EC_50 values, the toxic effects of Cu~0 on bacterial bioluminescence and seed germination were approximately 2 and 180 times greater than that of Fe~0, respectively. The toxicity increased with increasing CNT content in the Cu-CNT mixtures for both organisms,whereas opposite results were observed with Fe-CNT mixtures. The mean toxic effects of Cu-CNT(6%) were approximately 1.3–1.4 times greater than that of Cu-CNT(0%), whereas the toxic effects of Fe-CNT(6%) were approximately 2.1–2.5 times lower than that of Fe-CNT(0%) for both the bioluminescence activity and seed germination. The causes of this phenomenon are unclear at this point. More research will be needed to elucidate the mechanism of the toxicity of nano-mixture materials and the causes of the different patterns of toxicity with Cu-and Fe-CNT mixtures.     

一种硫离子响应杀菌材料的制备及应用研究

目的制备硫离子响应杀菌材料,研究它在不同浓度铜离子条件下的封装效果,以及在不同浓度硫离子条件下的释放行为。方法选择埃洛石纳米管为载体并用透射电镜进行表征、采用真空负载的方式,将甲硝唑和苯骈三氮唑(BTA)分步填充到埃洛石纳米管内部,使用紫外分光光度法测试不同浓度铜离子对纳米管中甲硝唑的封堵效果,以及材料在不同浓度硫离子条件下的释放情况。结果实验中通过调整铜离子浓度发现,铜离子浓度越大对甲硝唑的封堵效果越好,当铜离子浓度达到160 mmol/L时,对甲硝唑的封堵效果最好。杀菌材料在外界硫离子达到0.1mmol/L后,甲硝唑的释放浓度迅速提高,进一步提高硫离子浓度,释放情况改变不明显。结论铜离子浓度达到160 mmol/L时,材料的封装效果是最好的。材料能够对硫离子实现响应释放,且对应的临界浓度为0.1 mmol/L。     

典型铅锌矿化区不同土地利用类型土壤重金属污染特征与评价

选取云南者海典型铅锌矿区周边冶炼区（A）、粮食主产区（B）、保护区（C）三个区域土壤为研究对象,分析三个区域内林地（LD）和耕地（GD）土壤pH、总碳（TC）、总氮（TN）、总磷（TP）和5种重金属（Hg、Cd、Pb、Zn、Cu）含量,利用典范对应分析（CCA）研究不同土地利用类型下它们之间的关系,基于系统熵值与重金属生物毒性改进灰色聚类评价法对研究区重金属污染程度进行评价。结果表明,A、B、C三区土壤的5种重金属均超过云南省土壤背景值,且含量A区 > B区 > C区,所有土壤样品Hg、Cd、Pb、Zn、Cu平均含量分别为7.24、1.53、1 794、2 892、210 mg/kg;LD土壤重金属含量普遍高于GD。研究区土壤pH总体呈弱酸性,但A区土壤受矿业活动影响呈弱碱性。TC、TN含量和C/N值均表现出LD大于GD,但TP含量表现为GD显著大于LD （P<0.05）。CCA分析表明LD和GD土壤pH与Cd和Cu呈负相关,与Zn和Pb呈正相关,且pH对重金属含量的影响最大;TC、TP与重金属Cd和Cu在LD土壤中呈正相关,在GD土壤中呈负相关。改进灰色聚类评价结果表明重金属污染程度均表现为LD大于GD;A区污染最严重且均呈重度污染,B区次之,C区污染程度最轻。经比较本文改进的灰色聚类评价法在准确性和灵敏度方面优于传统方法。     

Assessing protected area effectiveness using surrounding (buffer) areas environmentally similar to the target area

Many studies are based on the assumption that an area and its surrounding (buffer) area present similar environmental conditions and can be compared. For example, in order to assess the effectiveness of a protected area, the land use/cover changes are compared inside the park with its surroundings. However, the heterogeneity in spatial variables can bias this assessment: we have shown that most of the protected areas in Mexico present significant environmental differences between their interior and their surroundings. Therefore, a comparison that aims at assessing the effectiveness of conservation strategies, must be cautioned. In this paper, a simple method which allows the generation of a buffer area that presents similar conditions with respect to a set of environmental variables is presented. The method was used in order to assess the effectiveness of the Calakmul Biosphere Reserve, a protected area located in the south-eastern part of Mexico. The annual rate of deforestation inside the protected area, the standard buffer area (based upon distance from the protected area only) and the similar buffer area (taking into account distance along with some environmental variables) were 0.3, 1.3 and 0.6%, respectively. These results showed that the protected area was effective in preventing land clearing, but that the comparison with the standard buffer area gave an over-optimistic vision of its effectiveness.     

Application of CFD Methods for Modelling in Air Pollution Problems: Possibilities and Gaps

Different urban air pollution problems deal with complex structure of air flows and turbulence. For such problems the Computer Fluid Dynamics (CFD) methods become widely used. However, this approach despite a number of advantages has some problems. Experience of use of CFD tools for development of models and suggestions of their applications for a local scale air pollution over a complex terrain and stable stratification are discussed in this paper, including: Topography and complex geometry: choose of the co-ordinate system and computer grid; Turbulence closure for air pollution modelling: modified k- model for stable stratified ABL; Boundary conditions for vertical profiles of velocity for stable-stratified atmosphere; Effects of the radiation and thermal budget of inclined surfaces to dispersion of pollutants; Artificial sources of air dynamics and circulation.Some examples of CFD applications for air pollution modelling for a flat terrain, mountainous area, mining open cast and indoor ventilation are discussed. Modified k- model for stably-stratified ABL is suggested. Due to the isotropic character of the k- model a combination of it in vertical with the sub-grid turbulence closure in horizontal can be more suitable for ABL. An effective scheme of boundary conditions for velocity profiles, based on the developed similarity theory for stable-stratified ABL, is suggested. Alongside with the common studies of atmospheric dispersion, the CFD methods have also demonstrated a good potential for studying anthropogenic and artificial-ventilation sources of air dynamic and circulation in local-scale processes of air pollution.