太湖悬浮物对水体生态环境的影响及其高光谱反演

利用太湖水质参数数据、水面以下实测光谱数据以及水-气界面辐射传输模型,计算得到了水体漫射衰减系数和水面以上遥感反射比,探讨了悬浮物对水体中营养盐以及水下光照等水体环境因子的影响,在此基础上,利用水面以上遥感反射率建立了悬浮物浓度的定量反演模型.研究结果表明:悬浮物浓度与水体下行漫射衰减系数具有很好的相关性,在可见光波段相关系数达到0.8以上,与真光层深度具有很好的负指数关系;水面以上遥感反射比与悬浮物浓度对数(In(Tss))具有很好的相关性,在500～600nm范围内呈负相关,在620-882nm范围呈正相关,最大负相关出现在522nm附近,最大正相关出现在692nm附近;选用Rra(522nm)、Rra(692nm)以及其比值作为变量建立悬浮物反演模型,得出的单波段线性对数模型能够较好地反演悬浮物浓度.     

离子选择性电极测定煤中氟浓度方法及影响因素分析

采用高温碱熔离子选择性电极法测量烟煤及石煤中氟化物浓度,对测量过程中的影响因素进行了分析,并对溶液的ｐＨ值及温度的影响进行了试验研究,结果表明该测量方法准确度较高,误差小,测量方便快速,实用性强,可作为煤及其它矿物质中氟含量测量的一种有效方法     

皮革铬鞣废水回收利用中铬渣的铬量测定

本文研究了皮革铬鞣废水中铬的定性特征曲线。利用吸光度加合定律对大量实测数据进行统计处理。建立测定铬的实验室校准直线方程,相关系数γ＝０．９９６０．以此作为测定铬鞣废水及回收铬渣中铬量的实验室回归直线方程。并对本法的可靠性进行研究,结果令人满意。本法不仅大大简化了铬量测定的步骤．而且在提高分析效率的同时获得同等的检测结果。     

北部湾海域江豚体内重金属含量及分布

应用原子吸收分光光度计对北部湾海域江豚的肌肉、脂肪、肝脏、胰脏、心脏、肺脏、肾脏、胃和肠管道等器官组织样品中的Cd、Cu、Zn、Pb、Cr、Ni、 Fe、Mn、Hg和As的含量进行测定,并使用标准物作了对照分析.结果显示,江豚体内各器官组织中的Cd、Cu、Zn、Pb、Cr、Ni、Fe、Mn、Hg和As的平均含量分别为(0.05～37.9)×10-6、(6.20～101.9 )×10-6、(24.38～181.5) ×10-6、(ND～1.85) ×10-6、(10.60～13.35)×10-6、(1.68～3.15)×10-6、(111.45～1413.8)×10-6、(0.35～12.43)×10-6、(0.21～34.36)×10-6和(0.28～3.81)×10-6(干重).江豚体内重金属含量高低的基本趋势是Fe>Zn>Cu>Cr>Ni>Cd>Mn> Hg>As>Pb.肝、肾脏等内脏器官中的重金属含量普遍高于肌肉及脂肪组织中的含量;胃组织中没有测出Pb的存在.与渤海和黄海江豚比较,北海湾海域江豚体内各种重金属的含量介于渤海和黄海江豚之间,说明该地区海域已受到重金属污染.     

Influence of thermal environment on metallographic structure characteristics of the electric arc bead pattern

Electrical apparatuses are prone to arc, which generally causes a fire, even an explosion hazard, when a flammable gas mixture is present, especially during industrial processes. Terrible fire scenes are challenging for fire investigations. In this work, by performing a simultaneous thermal analysis test we simulated a fire environment and found that as the oxygen concentration decreased, the oxidation/exothermic peak temperature of ‘cause’ bead became higher, but the melting temperature was unaffected. Results indicated that the bead pattern underwent oxidation at approximately 831 °C, melting initiated at approximately 1060 °C, and the pattern then disappeared. The melted pattern grain changes were divided into three critical temperature stages: Approximately 600 °C, the onset temperature at which the melted pattern grains began to be equiaxed; approximately 831 °C, at which the grains were interspersed with oxygen-containing material; and 831–1060 °C, when the grains disappeared, which is a criterion for identifying electrical fires. However, the boundaries remained throughout the thermal environment process. Moreover, the bead pattern demonstrated three metallographic regions: Deep layer (Region I), the intermediate layer (Region Ⅱ), and surface layer (Region Ⅲ). Region I was the most thermally sensitive, in which equiaxed crystals first appeared. Region Ⅲ was the thermal reaction lag zone, in which the typical branching crystals finally disappeared, and Region Ⅱ was intermediate between Regions I and Ⅲ. The results may help fire investigators determine the fire scene temperature stages and provide support for fire evidence extraction.     

Development of inherent safety and health index for formulated product design

The numerous formulated products which are introduced to the market consist of chemical ingredients that may cause various safety and health hazards to the consumers. Therefore, it is extremely important to practice a systematic methodology to formulate products with acceptable safety and health performances. This work presents an index-based methodology to assess the safety and health hazards of the ingredients during the early formulation stage of product design. Hence, new inherent safety and health sub-indexes are introduced to improve the current safety and health hazards that are needed in formulated product design. The inherent safety and health sub-indexes are assigned with scores based on the degree of potential hazards. A higher score indicates a higher safety risk or severe health effect, and vice versa. The proposed methodology will greatly assist the users to identify the adverse safety and health effects caused by the ingredients. Hence, it is pivotal to eliminate or reduce the safety and health impacts from product usage. A case study on common ingredients used in the formulation of paint is presented on this study to describe the proposed method.     

冬季烟塔合一烟气排放特性及其改善措施研究

针对烟塔合一冷却塔(Natural Draft Dry Cooling Tower,NDDCT)在冬季关闭冷却塔百叶窗时存在烟气排放困难的现象,以及导致冷却塔内污染物浓度大幅升高、进而增加冷却塔内壁腐蚀风险的问题,提出了增加烟囱高度的改善措施,并开展了风洞试验。基于计算流体力学(Computational Fluid Dynamics,CFD)方法建立了烟塔合一数值模型以获得冷却塔内部流场和污染物浓度场的分布特性,模拟对比了春季工况和冬季工况条件下烟塔合一冷却塔内部及出口位置的流场和烟气扩散特性。结果表明,由于百叶窗关闭导致冷却塔的通气量和换热量大幅度下降,冷却塔内部的流场变得杂乱无章,污染物质量分数大大增加。与春季相比,冬季冷却塔内壁污染物最大质量分数增加了1.5倍。随烟囱高度增加,烟气可以凭借其初始动能抵御冷却塔内的湍流冲出塔外,冷却塔内部的烟气扩散情况逐渐改善。定性风洞试验结果较好地验证了数值模拟结果,验证了该方法的可行性。虽然增加烟囱高度会增加施工初期的投资,但该方案能有效降低冷却塔的腐蚀风险,不但节省了后期防腐的投资,而且降低了安全风险。从长远来看,该措施利大于弊。     

Simultaneous nitrification and denitrification in activated sludge system under low oxygen concentration

Simultaneous nitrification and denitrification (SND), which is more economical compared with the traditional method for nitrogen removal, is studied in this paper. In order to find the suitable conditions of this process, a mixed flow activated sludge system under low oxygen concentration is investigated, and some key control parameters are examined for nitrogen removal from synthetic wastewater. The results show that SND is accessible when oxygen concentration is 0.3–0.8 mg/L. The nitrogen removal rate can be obtained up to 66.7% with solids retention time (SRT) of 45 d, C/N value of 10, and F/M ratio of 0.1 g COD/(g MLSS·d). Theoretical analysis indicates that SND is a physical phenomenon and governed by oxygen diffusion in flocs. Translated from Environmental Pollution and Control, 2004, 26(1): 11–13 [译自: 环境污染与防治]     

Critical phosphorus concentrations in winter wheat genotypes with various phosphorus efficiencies

１ＩｎｔｒｏｄｕｃｔｉｏｎＡｓａｎｕｎｒｅｎｅｗａｂｌｅｍｉｎｅｒａｌｒｅｓｏｕｒｃｅ，ｐｈｏｓｐｈｏｒｕｓｉｓｏｎｅｏｆｔｈｅｉｍｐｏｒｔａｎｔｅｓｅｎｔｉａｌｅｌｅｍｅｎｔｓｆｏｒｌｉｖｉｎｇｂｅｉｎｇｓ．Ｐｈｏｓｐｈｏｒｕｓｈａｓｍａｄｅａｇｒ...