优化模型在污泥处理厂选址中的应用

在我国大中城市,污水处理厂的不断兴建使污泥处理问题应运而生。采用混合整数优化模型可以解决污泥处理厂的科学选址问题,达到科学布点、合理运输、节省投资费用的目的。在传统厂群规划模型的基础上将目标规划、周密的约束条件等融于其中,并采用对于线形规划和非线性规划问题适用的LINGO软件进行求解。根据东莞市拟建的36个污水处理厂污泥产生预测情况,对污泥处理厂的设置进行了分析预测,详细对比了建一个、两个、三个污泥处理厂的运输费用、投资费用、运行费用等,最终确定兴建两个规模均为800t/d的处理厂,其位置分别位于东莞市厚街镇和常平镇,为厂址选择和规模提供了科学依据和保障。     

层次分析法在功能区噪声监测点位优选中的应用

运用层次分析法对功能区噪声进行优选,各功能区噪声监测点位个数分配根据功能区面积和复杂性、各功能区噪声监测点位确定根据专家比例标度赋值进行评定。     

基于条件高斯模拟的城市灰尘Pb元素的空间分布特征

城市灰尘是分散于城市不同区域的表面固体颗粒物。城市灰尘对城市环境造成的污染越来越多地受到人们的关注,尤其是城市灰尘重金属对城市生存环境造成的危害。本文利用R软件中的Gstat包,对金华市城市地表灰尘中的Pb元素含量进行500次条件高斯模拟,并从中随机抽出3次模拟对其模拟结果进行分析,从模拟结果可以看出研究区Pb元素总体上显示出相似的空间变化趋势,但在细部空间变化上是有差别的。条件高斯模拟法对未知点的模拟值具有不确定性,克服了普通克里格法的平滑效应,能够更好地反映研究区的随机性和结构性。     

Optimization of gasoline hydrocarbon compositions for reducing exhaust emissions

Effects of hydrocarbon compositions on raw exhaust emissions and combustion processes were studied on an engine test bench. The optimization of gasoline hydrocarbon composition was discussed. As olefins content increased from 10.0% to 25.0% in volume, the combustion duration was shortened by about 2 degree crank angle ( CA), and the engine-out THC emission was reduced by about 15%. On the other hand, as aromatics content changed from 35.0% to 45.0%, the engine-out NOx emissions increased by 4%. An increment in olefins content resulted in a slight increase in engine-out CO emission, while the aromatics content had little e ect on engine-out total hydrocarbon (THC) and CO emissions. Over the new European driving cycle (NEDC), the THC, NOx and CO emissions of fuel with 25.0% olefins and 35.0% aromatics were about 45%, 21% and 19% lower than those of fuel with 10.0% olefins and 40.0% aromatics, respectively. The optimized gasoline compositions for new engines and new vehicles have low aromatics and high olefins contents.     

两级SBR工艺去除磷、氮及有机物效能分析

以模拟生活污水为处理对象,在常温条件下,采用对比试验与机制分析方法,研究了两级SBR工艺分级除磷、去除有机物及脱氮的特性,分析了工艺的效能优势.结果表明,通过控制泥龄(除磷级5~7 d,脱氮级约50 d),可以将异养的PAOs与硝化菌分别控制在2个反应器中优势生长,在出水水质更优的情况下,系统的处理效率可比单级SBR提高1倍以上;两级SBR系统可以有效地缓解有机负荷对硝化过程的冲击影响,在进水COD浓度较高的情况下,能够保持其脱氮级(SBS2)具有稳定的硝化速率,且系统的最终出水可以容易并稳定地达到TP≤0.5 mg.L-1的国家标准;另外,两级SBR的脱氮级(SBS2)除具有优势的硝化菌种外,还能培养出适合降解难降解有机物的异养菌,使其好氧硝化结束时COD浓度较单级SBR系统更低.     

基于响应面优化条件下柚皮对Pb2+的吸附

采用Plackett-Burman(P-B)法和中心复合设计(Central Composite Design,简称CCD)对影响柚皮吸附Pb2+的6个条件进行筛选优化.P-B实验设计与统计学分析表明:pH值、Pb2+初始浓度、吸附剂用量是影响吸附率的3个关键因素.以吸附率为响应目标,对3因素进行中心复合设计,并经响应面法优化分析得到影响吸附率的二阶模型,确定了Pb2+吸附实验的最优操作条件:pH值5.4.Pb2+初始浓度为265.86mg·L-1,吸附剂用量为2.56 g·L-1,实测吸附率达到92.47%,吸附量为96.01 mg·g-1;整个吸附过程吸附剂柚皮没有经过任何化学预处理.效果优于一般的天然吸附剂.研究结果表明,柚皮是一种很具潜力的环保型廉价吸附剂.     

Application of response surface methodology for the optimization of biodiesel production from yellow mustard (Sinapis alba L.) seed oil

In the present study, response surface methodology (RSM) involving central composite design (CCD) was applied to optimize the reaction parameters of biodiesel production from yellow mustard (Sinapis alba L.) seed oil during the single-step transesterification process. A total of 30 experiments were designed and performed to determine under the effects of variables on the biodiesel yield such as methanol to oil molar ratio (2:1–10:1), catalyst concentration (0.2–1.0 wt.% NaOH), reaction temperature (50–70°C), and reaction time (30–90 min). The second order polynomial model was used to predict the biodiesel yield and coefficient of determination (R²) was found to be at 0.9818. The optimum biodiesel yield was calculated as 96.695% from the model with the following reaction conditions: 7.41:1 of methanol to oil molar ratio, 0.63 wt. % NaOH of catalyst concentration, 61.84°C of reaction temperature, and 62.12 min of reaction time. It is seen that the regression model results were in agreement with the experimental data. The results showed that RSM is a suitable statistical technique for optimizing the reaction parameters in the transesterification process in order to maximize the biodiesel yield.     

Performance of a diesel engine with water emulsified diesel prepared with optimized process parameters

An attempt has been made to produce stable water–diesel emulsion with optimal formulation and process parameters and to evaluate the performance and emission characteristics of diesel engine using this stable water–diesel emulsion. A total of 54 samples were prepared with varying water/diesel ratio, surfactant amount and stirring speed and water separation was recorded after 24 and 48 hr of emulsification. The recorded data were used in artificial neural network (ANN)-particle swarm optimization (PSO) technique to find the optimal parameters to produce water–diesel emulsion for engine testing. The predicted optimal parameters were found as 20% water to diesel ratio, 0.9% surfactant and 2200 rpm of stirrer for a water separation of 14.33% in one day with a variation of 6.54% against the actual value of water separation. Water–diesel emulsion fuel exhibited similar fuel properties as base fuel. The peak cylinder gas pressure, peak pressure rise rate and peak heat release rate for water–diesel were found higher as compared to diesel at medium to full engine loads. The improved air-fuel mixing in water–diesel emulsion enhanced brake thermal efficiency (BTE) of engine. The absorption of heat by water droplets present in water–diesel emulsion led to reduced exhaust gas temperature (EGT). With water–diesel emulsion fuel, the mean carbon monoxide (CO), unburned hydrocarbon and oxides of nitrogen (NO_x) emissions reduced by 8.80, 39.60, and 26.11%, respectively as compared to diesel.     

基于最小能量原理的平衡图调节法在矿井通风系统优化中的应用

根据最小能量原理,采用平衡图调节法解决矿井通风网络中风压不平衡的问题,建立矿井通风网络优化模型。根据矿山基本情况和平衡图原理绘制出通风网络"平衡图",采用不同的变换方法使得"平衡图"真正达到平衡,进而得出不同的优化调节方案,并进行风压平衡的验证。应用最小能量原理选出能耗最低的调节方案。并且,运用基于最小能量原理的平衡图调节法解决了矿山的实际问题,结果表明,运用该方法能形象直观地反映出风量、风压及功率之间的关系,在解决通风网络中风压不平衡问题的同时,既形象直观,又使得经济费用最低,保证矿山安全高效生产。     

An energy-absorbing sliding seat for reducing neck injury risks in rear impact—analysis for prototype built

Objective: This study investigated overall performance of an energy-absorbing sliding seat concept for whiplash neck injury prevention. The sliding seat allows its seat pan to slide backward for some distance under certain restraint force to absorb crash energy in rear impacts.

Methods: A numerical model that consisted of vehicle interior, seat, seat belt, and BioRID II dummy was built in MADYMO to evaluate whiplash neck injury in rear impact. A parametric study of the effects of sliding seat parameters, including position and cushion stiffness of head restraint, seatback cushion stiffness, recliner characteristics, and especially sliding energy-absorbing (EA) restraint force, on neck injury criteria was conducted in order to compare the effectiveness of the sliding seat concept with that of other existing anti-whiplash mechanisms. Optimal sliding seat design configurations in rear crashes of different severities were obtained. A sliding seat prototype with bending of a steel strip as an EA mechanism was fabricated and tested in a sled test environment to validate the concept. The performance of the sliding seat under frontal and rollover impacts was checked to make sure the sliding mechanism did not result in any negative effects.

Results: The protective effect of the sliding seat with EA restraint force is comparable to that of head restraint–based and recliner stiffness–based anti-whiplash mechanisms. EA restraint force levels of 3 kN in rear impacts of low and medium severities and 6 kN in impacts of high severity were obtained from optimization. In frontal collision and rollover, compared to the nonsliding seat, the sliding seat does not result in any negative effects on occupant protection. The sled test results of the sliding seat prototype have shown the effectiveness of the concept for reducing neck injury risks.

Conclusion: As a countermeasure, the sliding seat with appropriate restraint forces can significantly reduce whiplash neck injury risk in rear impacts of low, medium, and high severities with no negative effects on other crash load cases.