同步进出水SBR设备最佳进水方式流态模拟

借助流体计算软件Fluent对某同步进出水SBR设备4种不同进水位置以及3种进水孔排布分别进行流态模拟,根据模拟结果得到最佳的进水方式;同时在该进水方式下对进水流量为0.5、0.7、1.0、1.3和1.5 m3/h时反应器内的流态分布情况进行了数值模拟,最后通过示踪剂实验与模拟结果对比验证。对于实验用SBR(长×宽×高为2 m×2 m×1.2 m),进水流量1.0 m3/h是最佳进水流量,此时反应器内流态稳定,进水区域主要分布于反应器中下部以及远离堰口的池壁附近,死水区面积较小,冲击负荷适中,进水对出水水质影响较小;当进水流量小于1.0 m3/h时,进水主要分布于反应器池底,对角线方向以及远离进水端池壁附近3个区域且彼此相对独立,池内死水区面积较大;当进水流量大于1.0 m3/h时,进水冲击负荷过大,迅速形成短流,影响出水水质。     

曝气条件对浸没式膜生物反应器内流场的影响

为深入研究流场动力学特性对浸没式膜生物反应器系统内膜面污染的控制,应用fluent软件对浸没式膜生物反应器内气液两相流动进行了三维数值模拟研究。采用标准k-ε湍流模型和欧拉多相流模型,考察了改变曝气条件对膜面气液速度场及气含率分布的影响。模拟结果表明,在相同曝气强度下,1 mm曝气孔径下膜面气液两相的速度增加较孔径2 mm、3 mm的快;曝气孔径为1 mm时,膜面的液相速度随着曝气强度的增加逐渐增大;曝气孔径为1 mm时,曝气量为5.5 m3/h所形成的漩涡区较大,膜面气含率值较高且分布较均匀,气液两相接触面积较大,膜面冲刷效果较好;模拟观察到反应器底部靠近壁面局部气含率较低,不利于活性污泥中微生物的生长,需要进一步优化曝气和反应器结构。     

SCR脱硝系统烟道内流场优化

为了改善选择性催化还原法(SCR)催化剂上游烟气的流场、温度场和浓度场分布,基于CFD仿真分析技术,建立了整个脱硝系统三维模型,并通过优化导流板及整流格栅,使得速度标准偏差、浓度标准偏差、温度偏差、速度偏转角以及压降等性能指标都满足设计要求,在满足脱硝效率和氨逃逸率前提下,大大降低了烟气对催化剂层的冲刷,保证催化剂的使用寿命。最后,为了合理布置吹灰器,对优化结构下粉尘颗粒在烟道内的运动情况进行了仿真分析研究,为设计提供了依据。     

电弧流溶胞技术促进污泥厌氧消化

为提高污水厂处理污泥时的厌氧消化速率,利用电弧流溶胞技术处理剩余污泥,研究电弧流溶胞技术对污泥破解预处理效果的影响.实验结果表明,与未经预处理的污泥相比,电弧流溶胞处理能够明显提高污泥厌氧消化效率,增加有机物含量和沼气产量.其中,经处理后的污泥TS、VS剩余量分别降低了8.3%和6.3%,COD增加了11.9%.厌氧系统平均产气量平均增加79.76 L/d,增加率45.82%,甲烷含量增加1.03 L/d,增加率102%.由此说明,电弧流溶胞技术可以提高厌氧消化反应中有机物的去除率,有效促进厌氧消化中污泥的水解过程,显著增加甲烷气体的产生量.在综合考虑运行费用和污泥消化效果的前提下,采取适宜的电弧流强化处理措施有一定的积极意义.     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9%~5.4%.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3%的系统脱硫效率整体高于含湿量为5%和4%的样品,最大值达93.56%.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3%的循环脱硫灰较含湿量为5%的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5%样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaSO3干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

Treatment of wastewater from red and tropical fruit wine production by zeolite anaerobic fluidized bed reactor

A study of the anaerobic treatment of wastewaters derived from red (RWWW) and tropical fruit wine (TFWWW) production was carried out in four laboratory-scale fluidized bed reactors with natural zeolite as bacterial support. These reactors operated at mesophilic temperature (35°C). Reactors R1 and R2 contained Chilean natural zeolite, while reactors R3 and R4 used Cuban natural zeolite as microorganism support. In addition, reactors R1 and R3 processed RWWW, while reactors R2 and R4 used TFWWW as substrate. The biomass concentration attached to zeolites in the four reactors studied was found to be in the range of 44–46 g volatile solids (VS)/L after 90 days of operation time. Both types of zeolites can be used indistinctly in the fluidized bed reactors achieving more than 80%–86% chemical oxygen demand (COD) removals for organic loading rates (OLR) of up to at least 20 g COD/L d. pH values remained within the optimal range for anaerobic microorganisms for OLR values of up to 20 and 22 g COD/L d for RWWW and TFWWW, respectively. Toxicity and inhibition levels were observed at an OLR of 20 g COD/L d in reactors R1 and R3 while processing RWWW, whereas the aforementioned inhibitory phenomena were not observed at an OLR of 24 g COD/L d in R2 and R4, treating TFWWW as a consequence of the lower phenolic compound content present in this substrate. The volatile fatty acid (VFA) levels were always lower in reactors processing TFWWW (R2 and R4) and these values (< 400 mg/L, as acetic acid) were lower than the suggested limits for digester failure. The specific methanogenic activity (SMA) was twice as high in reactors R2 and R4 than in R1 and R3 after 120 days of operation when all reactors operated at an OLR of 20 g COD/L d.     

Experimental study of humidity influence on triboelectric charging of particle-laden duct flows

Electrostatic charge on powders arises during pneumatic transport due to particle–particle and particle–surface interactions via triboelectrification. This is a potential threat to the safety of industrial production and the source of numerous fires and dust explosions in the past. Triboelectric charges are affected by environmental conditions, such as ambient temperature and relative humidity. In this work, we experimentally investigated the influence of ambient humidity on the particle charge of gas–solid flows in a square-shaped duct. Monodisperse PMMA particles are fed into a fully developed airflow in a PMMA duct and then pass through a metallic duct section. The charge of particles is measured at the outlet of the metallic duct via a Faraday cup. By measuring the electrostatic charge under various environmental conditions, we observed that the electrostatic charge first increases with the humidity and then decreases when the humidity becomes higher.     

大型公园道路网络关键节点脆弱性评价

为更加科学有效地辨识景区道路网络中的客流关键节点,以节点脆弱性为度量指标,提出1种基于FIM模型的关键节点脆弱性评价方法.以某大型公园为例,首先通过ArcGIS软件将该公园的道路网络信息转换成可编译的文本信息,经过Java枚举可行路径,然后利用嵌入FIM算法的Lingo进行优化,得出网络节点的重要度.最后综合节点容量、...     

不同墩高下连续刚构桥抗震性能分析

以某大跨连续高墩刚构桥为依托,采用Midas/civil软件建立仿真模型,通过时程分析方法研究双肢薄壁墩参数在地震响应下对高墩连续刚构桥抗震性能的影响.以桥墩高度为主要参数,以模型阵型频率、桥墩墩顶、墩底位移及内力变化三个方面对其抗震性能进行评价.研究结果表明,随着其中一个桥墩高度的增加,桥梁频率不断减小,矮墩墩底及矮...     

考虑气液置换的压回法气井压井过程对井底压力的影响

为在压回法气井压井计算中进一步贴合现场实际情况,提出新的压回法气井压井过程计算方法.在压井过程中,考虑压井液与侵入井筒的气体发生置换,导致井筒流体自上而下分布为液-气液2相-气-气液2相的实际问题,建立压井过程模型,并对井底压力的变化进行计算分析.结果表明:发生气液置换对压回法压井过程井底压力以及注入压力具有明显影响,...