单缸摩托车发动机中低速性能优化

目的 解决某单缸摩托车发动机台架测试时中低速扭矩线性度差的问题.方法 基于CFD数值分析方法,运用热力学仿真分析软件GT-Power对发动机进行建模和标定,然后对原方案发动机进行摸底分析,最后通过优化配气机构和进排气系统来实现改善中低速性能的目标.结果 优化后的发动机台架测试结果中,发动机中低速扭矩线性度改善,动力性和经济性及排放都达到项目预期目标,峰值功率达到16 kW(9500 r/min),峰值扭矩达到18.6 N·m(7000 r/min),最低比油耗为183 g/(kW·h),CO、THC、NOx排放量分别为840、83、54 mg/km.配气机构运动学动力学性能与可靠性提升,进排气凸轮丰满系数分别达到5.14、5.15.结论 原方案中低速扭矩线性度差的原因为此转速段充气效率较低.优化凸轮型线、空滤器、消声器、排气管道参数能更好地利用进排气管道谐振效应来提升发动机中低速动力性能.     

氢氧化钠吸收—盐酸萘乙二胺分光光度法测定污染源废气中的氮氧化物

对非稳态工艺废气中氮氧化物的监测 ,目前的监测方法无法获得准确满意的结果 .氢氧化钠吸收—盐酸萘乙二胺分光光度法监测 ,可以延长采样时间 ,扩大测定范围 ,消除了推荐、试行方法中的有关缺陷     

辽宁省机动车污染防治对策探讨

辽宁省机动车保有量大、增长速度快，机动车污染物排放总量不断增加，给城市环境空气质量改善带来巨大压力，本文根据辽宁省机动车污染实际情况，提出了辽宁省机动车污染的防治对策。     

Random walk modeling of wake dispersion for the exhaust tower of an underground tunnel in urban area

ＩｎｔｒｏｄｕｃｔｉｏｎＲｅｃｅｎｔｌｙ，ｓｏｍｅｉｎｓｔａｌｌａｔｉｏｎｓｗｉｔｈｓｐｅｃｉａｌｃｏｎｓｔｒｕｃｔｉｏｎｆｏｒｅｘｔｒａｃｔｉｎｇｃｏｎｔａｍｉｎａｎｔｇａｓ，ｓｕｃｈａｓａｎｅｘｈａｕｓｔｔｏｗｅｒｏｆｔｈｅｕｎｄｅｒｇｒｏｕｎｄｔｕｎｎｅｌ，ｅｔｃ．ｗｅｒｅｓｅｔｕｐｉｎｕｒｂａｎａｎｄｉｎｄｕｓｔｒｉａｌｃｏｍｐｌｅｘａｒｅａｓ．Ｔｈｅｅｆｆｅｃｔｓｏｆｔｈｅｓｅｃｏｎｓｔｒｕｃｔｉｏｎｓｏｎｔｈｅｆｌｏｗａｎｄｔｈｅｒｅｂｙｏｎｔｈｅｌｏｃａｌｄｉｓｐｅｒｓｉｏｎｏｆｔ…     

上海市大气中非甲烷烃与机动车尾气排放研究

采用特征性化合物法和统计法相结合的方法,对上海市大气中非甲烷烃(NMHC)与作为机动车尾气特征性化合物的CO与Pb进行了相关性分析。结果发现,NMHC与Pb在显著性水平0.01下显著性相关,相关系数达到0.593(n=18);NMHC与CO小时均值相关系数达到0.495(n=2329),日均值相关系数达到0.581(n=114)。从而判断机动车尾气排放已经逐渐成为上海市大气中NMHC的主要贡献者。     

麻石文丘里洗涤吸收器在APV尾气处理上的应用

介绍了ＡＰＶ喷雾干燥尾气的性质，原尾气系统存在的问题，改造中采取的措施、原理、流程和取得的效果。实践证明，用“麻石文丘里一次降温、洗涤—ＸＰ型塔板二次洗涤—旋流除雾器除雾”的改造方案，取代原“换热器降温—喷淋塔洗涤—折流脱水器脱水”的流程，取得了良好的降温、洗气和除雾效果，且工程费用低。     

新型射汽抽气消声器

介绍了一种自行设计的、新型的汽轮机启动抽气器排汽消声装置，并对其结构原理和设计特点进行了较详细的叙述。应用实践表明，此种消声器降噪效果明显。     

贫燃条件下汽车尾气中NOx催化净化研究进展

汽车尾气排放的NOx(主要是NO)是城市大气的主要污染源之一。本综述了近l0年来贫燃条件下NOx催化转化为N2的催化剂研究进展。这些方法包括HC-SCR、NO直接催化分解、NOx吸附-还原等。讨论了不同催化剂的性能影响因素。新的负载材料MFI、MCM-41、SAPO-34的应用增强了催化剂的性能。双功能催化剂由于两种活性位的协同作用表现出较高的活性和选择性。新的纳米结构概念催化剂NOx吸附还原中发现有广泛应用。介绍了上述催化脱除NOx的各种机理并指出了今后研究的方向。     

抽出式通风煤巷掘进过程中粉尘浓度分布规律的数值模拟

根据气固两相流理论，针对矿井掘进工作面的特点，采用计算流体力学的离散相模型（DPM）对掘进工作面通风过程中粉尘浓度进行数值模拟，总结抽出式通风掘进巷道中粉尘浓度的沿程分布及变化规律。     

Valorisation of used cooking oil sludge by codigestion with swine manure

The addition of lipid wastes to the digestion of swine manure was studied as a means of increasing biogas production. Lipid waste was obtained from a biodiesel plant where used cooking oil is the feedstock. Digestion of this co-substrate was proposed as a way of valorising residual streams from the process of biodiesel production and to integrate the digestion process into the biorefinery concept.Batch digestion tests were performed at different co-digesting proportions obtaining as a result an increase in biogas production with the increase in the amount of co-substrate added to the mixture. Semi-continuous digestion was studied at a 7% (w/w) mass fraction of total solids. Co-digestion was successful at a hydraulic retention time (HRT) of 50 d but a decrease to 30 d resulted in a decrease in specific gas production and accumulation of volatile and long chain fatty acids. The CH₄ yield obtained was 326 ± 46 l/kg VS_feed at an HRT of 50 d, while this value was reduced to 274 ± 43 l/kg VS_feed when evaluated at an HRT of 30 d. However these values were higher than the one obtained under batch conditions (266 ± 40 l/kg VS_feed), thus indicating the need of acclimation to the co-substrate. Despite of operating at low organic loading rate (OLR), measurements from respirometry assays of digestate samples (at an HRT of 50 d) suggested that the effluent could not be directly applied to the soil as fertiliser and might have a negative effect over soil or crops.