聚合硅酸硫酸铝铁的制备与应用

在n(Fe A1)／n(Si)为0．5～1．0、n(Al)／n(Fe)为2．5～3．0、SiO2质量分数为2．3％、硅酸钠溶液的活化pH为5．5、硅酸钠溶液的活化时间为12min或SiO2的质量分数为2．0％、硅酸钠溶液的活化pH为6．0、硅酸钠溶液的活化时间为3min的条件下，制备出的聚合硅酸硫酸铝铁对废水的除浊效果最佳，除浊率大于98％。     

超高强度钻杆低温断裂性能及裂纹扩展特征研究

超高强度钻杆在冬季低温环境下容易发生脆性断裂事故,为了从断裂力学角度揭示其冷脆现象的本质,采用ZBC2302-D型示波冲击试验机,获得了不同温度下超高强度钢在冲击断裂过程中的力-位移曲线,并对比分析了冲击功、起裂功和裂纹扩展功之间的变化关系。采用国家标准GB 4161—2007中的计算公式,计算了冲击试样的裂纹扩展量Δa和阻抗应力强度因子K_R;同时,引入K_R阻力曲线,得到超高强度钻杆在不同温度下的剩余强度图。结果表明,当冲击试样开始出现裂纹时,随温度降低,钻杆的初始起裂应力有所增加,出现硬化现象。当钻杆出现一定长度的裂纹时,随温度降低,阻抗应力强度因子越来越小,而且降低速度越来越快,剩余强度也表现出相同的变化趋势。随温度降低,材料抵抗裂纹扩展的能力逐渐下降,表明钻杆在低温下更容易断裂。     

Leaching behaviour of different scrap materials at recovery and recycling companies: Full-, pilot- and lab-scale investigation

Scrap material recovery and recycling companies are confronted with waste water that has a highly fluctuating flow rate and composition. Common pollutants, such as COD, nutrients and suspended solids, potentially toxic metals, polyaromatic hydrocarbons and poly chlorinated biphenyls can exceed the discharge limits. An analysis of the leaching behaviour of different scrap materials and scrap yard sweepings was performed at full-scale, pilot-scale and lab-scale in order to find possible preventive solutions for this waste water problem. The results of these leaching tests (with concentrations that frequently exceeded the Flemish discharge limits) showed the importance of regular sweeping campaigns at the company, leak proof or covered storage of specific scrap materials and oil/water separation on particular leachates. The particulate versus dissolved fraction was also studied for the pollutants. For example, up to 98% of the polyaromatic hydrocarbons, poly chlorinated biphenyls and some metals were in the particulate form. This confirms the (potential) applicability of sedimentation and filtration techniques for the treatment of the majority of the leachates, and as such the rainwater run-off as a whole.     

Revisiting the national corporate social responsibility index

This paper relies on Gjølberg’s national corporate social responsibility (CSR) index while its purpose is twofold. First, it seeks to extend the methodological instrument for assessing national CSR and, second, it applies the new approach to a much larger pool of countries (n = 86) in an attempt to provide a global CSR outlook. The emergent picture from the study is one of deficient CSR penetration and wide variation among countries where most of the assessed countries are still lagging in the endorsement of international CSR initiatives and schemes. Findings offer fertile ground to theorists and researchers for a deeper investigation of the national specificity of CSR and to further identify institutional determinants that shape the social responsiveness and self-regulation of business entities. The study has also implications for managers and top executives to consider as it infers that the national background can be influential in the development of a CSR agenda and can condition the level of CSR penetration.     

Pseudomonas sp. ZXY-1, a newly isolated and highly efficient atrazine-degrading bacterium, and optimization of biodegradation using response surface methodology

Atrazine, a widely used herbicide, is increasing the agricultural production effectively, while also causing great environmental concern. Efficient atrazine-degrading bacterium is necessary to removal atrazine rapidly to keep a safe environment. In the present study, a new atrazine-degrading strain ZXY-1, identified as Pseudomonas, was isolated. This new isolated strain has a strong ability to biodegrade atrazine with a high efficiency of 9.09 mg/L/hr.Temperature, p H, inoculum size and initial atrazine concentration were examined to further optimize the degradation of atrazine, and the synthetic effect of these factors were investigated by the response surface methodology. With a high quadratic polynomial mathematical model(R~2= 0.9821) being obtained, the highest biodegradation efficiency of 19.03 mg/L/hr was reached compared to previous reports under the optimal conditions(30.71°C, pH 7.14, 4.23%(V/V) inoculum size and 157.1 mg/L initial atrazine concentration).Overall, this study provided an efficient bacterium and approach that could be potentially useful for the bioremediation of wastewater containing atrazine.     

一种多介质层波形潜流人工湿地处理重污染河水试验

我国河流污染严重,城市黑臭水体的比率日益增加。人工湿地作为一种高效低耗能的绿色处理技术,已被广泛应用于污染河水的治理。通过对比分析分层装填复合填料的多介质层波形潜流人工湿地和单一砾石填料的普通人工湿地处理重污染河水的效果,研究了特种基质填料强化脱氮除磷作用以及不同水力负荷条件的影响。试验结果表明:在水力负荷为0.2 m~3/(m~2·d)时,普通湿地对COD、NH3-N、TN和TP的去除率分别达到55.95%、77.85%、39.80%和54.94%;多介质层湿地对COD、NH3-N、TN和TP的去除率分别达到58.52%、75.99%、67.08%和57.31%。在水力负荷为0.5 m~3/(m~2·d)时,普通湿地对COD、NH3-N、TN和TP的去除率分别达到68.46%、90.73%、42.13%和53.70%;多介质层湿地对COD、NH3-N、TN和TP的去除率分别达到69.61%、89.94%、77.58%和68.63%,其脱氮效果明显好于普通湿地。以复合填料包分层装填的波形潜流人工湿地系统具有良好的脱氮除磷效果,有很好的推广应用价值。     

建筑材料隐含环境影响评估

我国建筑业快速发展,建筑开发使用大量的建筑材料给资源和环境带来严重负荷.以上海市为案例,运用生命周期评价方法,基于北京工业大学和Ecoinvent数据库中的建筑材料生产数据,采用ReCiPe法对上海市建筑物的材料隐含环境影响进行评估,并对未来的环境影响潜值进行预测.结果表明:在上海市居住建筑和非居住建筑所产生的各类环境影响中人类毒性、金属损耗最为突出,约占总环境影响的45%和20%;环境影响主要来源于钢筋和木材的生产,对各类环境影响贡献度分别约为47%、17%;高层居住建筑和非居住建筑中的工厂建筑物化环境影响在各自类型中所占比例最高.按现有趋势发展,2020年上海市居住建筑开发规模和环境影响潜值均将达到2014年的1.52倍,非居住建筑则可达到2014年的1.14倍.针对上海市建筑材料环境影响分析结果,为有效减轻上海市建筑物的环境影响,需重点关注钢筋、铝材、木材以及混凝土的生产,识别生产过程中污染物转移环节进而改进工序;在设计阶段考虑选择环境影响负荷低的绿色建材,如混凝土砌块、高性能混凝土等,从而降低环境影响;同时,应重点关注隐含环境负荷高的高层居住和工厂建筑类建筑,通过降低建材使用量等方案降低环境影响.      

铁锰氧化物/坡缕石复合材料吸附磷的性能

将铁锰氧化物与坡缕石黏土结合制备了复合材料FO/P、MO/P和FMO/P,由静态吸附实验研究了复合材料吸附磷的性能,考察了氧化物与坡缕石质量比、焙烧温度、溶液p H值、离子强度和振荡时间对吸附量的影响,探讨了吸附动力学、吸附平衡和机理。结果表明,FMO/P的吸附性能优于FO/P和MO/P,铁锰氧化物与坡缕石黏土的质量比为0.1的FMO/P对20mg/L的磷溶液去除率可达95%,吸附量明显受溶液p H的影响,离子强度对吸附量影响较小,磷吸附在复合材料表面主要形成内层络合物,60 min可基本达吸附平衡,过程符合pseudo-second-order方程,具有化学吸附的性质,FMO/P吸附等温线符合Freundlich方程,有不均匀吸附的性质,饱和吸附量达49 mg/g。     

军绿有机涂层破损腐蚀行为研究

目的研究不同破损程度下军绿有机涂层的腐蚀行为,确定破损率对其防护性能变化的影响。方法通过人工制作不同的破损率,并利用电化学阻抗谱技术,研究不同破损程度下军绿有机涂层的电化学特征。结果根据不同破损程度下的军绿有机涂层的电化学特征,确定了涂层从完好到失效的四个阶段,初始完好阶段(破损率K≤0.0004%)、破损增大阶段(0.0016%K≤0.04%)、破损过大阶段(0.16%K≤1%)和失效阶段(4%K≤16%)。结论破损率K为0.04%的点是该涂层防护性能急转直下的转折点,因此破损率K大于0.04%时,应及时对车辆表面涂层进行修补和防护。     

多层阻尼复合板常温贮存5年性能研究

目的分析多层阻尼复合板常温贮存5年的性能变化。方法对多层阻尼复合板进行常温下贮存5年的减振性能研究,通过贮存前后的正弦扫描试验和随机振动试验,获得贮存前后多层阻尼复合板的减振性能和模态变化,进行对比分析。结果阻尼复合板常温贮存5年后,径向模态有较大的下降,法向模态变化较少,组件上的加速度响应基本无变化。结论该多层阻尼复合板常温贮存5年后仍然满足要求。