基于汶川8.0级强震记录的近场地震动特征分析

在汶川8.0级大地震中,国家数字强震动台网布设在龙门山断裂带及其周围地区的50多个台站获得了大于100 Gal的加速度记录。选取其中断层附近11个台站的加速度记录,分别进行了地震反应谱分析和基于正交化HHT法的能量分布特征分析,通过对竖向与水平向加速度峰值比、竖向与水平向加速度反应谱比值,以及能量分布和峰值系数的分析与比较,探讨了汶川地震的近场地震动特征。     

我国台风灾害救助应急响应的时空分布特征

基于2005 - 2010年历次台风灾害救助应急响应的启动和损失情况,在统计分析响应频次和响应灾情的基础上,研究分析了国家台风灾害救助应急响应的时空分布特征.结果表明,国家台风灾害救助应急响应的时空分布特征大致反映了我国重大台风灾害损失的时空分布特征和我国台风灾害救助工作的发展变化和新思路:①2005 - 2010年,国家共针对24次台风过程启动救助应急响应51次,平均每年8.5次,其中四级、三级响应分别为41次、10次,平均每年6.8次、2.5次,分别占80％和20％.②7-9月国家启动台风应急响应最多,10月、5月和4月偶有分布.③近年重大台风损失2005 - 2006年严重,2007 - 2010年则较轻;国家针对台风灾害启动响应从东南沿海向内陆和北方沿海省份递减.④紧急转移安置人口是启动响应依据最多的指标,且呈现明显的逐年下降趋势,反映了近年来国家对台风灾害救助工作的重视和以“预防为主”的应急管理新思路.     

西南山区某气井井场地基稳定性模拟分析

中国西南山区蕴藏着丰富的天然气资源,但随着开发规模的日益扩大,天然气井逐步转向山区这类地质环境恶劣的地区。本文以西南山区某气井为原型,在详细阐明井场区地质环境背景特征的基础上,首先对井场出现的典型地质问题——地下采空区进行定性判断和分析;之后选用F lac-2D有限差分软件,对井场加载前/后地下采空区可能造成的井场地基应力和变形特征,采用双洞和采空区这2种计算模型,进行数值模拟分析。模拟结果表明,井场加载前/后地基最大位移量为2 mm,地基局部地段出现拉应力区,但总体上地基稳定。研究结论将为后期建设中井场建筑物的优化布局及基础的选型提供依据。     

直埋式光纤传感钻孔注浆耦合材料配合比试验研究

采用钻孔埋设传感光纤是岩土体分布式光纤传感直埋技术的一种,为使传感光纤与周围土体变形协调,通常在钻孔内注浆,使传感光纤与周围岩土介质凝固为一体。根据对浆液凝固时间无特定要求和有特定要求的2种情况,通过试验研究了钻孔注浆耦合材料、配合比及其凝固后强度。结果表明:通过调整水泥与膨润土的比例以及水固比可以控制凝固体的无侧限抗压强度,使其强度与原位岩土体的近似相同;添加适量的水玻璃可以加快浆液的凝固速度。针对石家庄某隧道原位土体的力学参数,得到了满足现场施工要求的最优配合比,使浆液凝固后的力学指标与原位土体的近似相同。     

济南市南部山区降雨特性分析

通过对济南市南部山区50年降雨资料的分析,得出南部山区年降雨量为648mm,降雨季节性明显,降雨量主要集中在6-8月份的降雨特点;采用皮尔逊Ⅲ型曲线拟合了降雨频率曲线,分析了降雨量与频率之间的关系,得出年降雨量在1000mm以上的频率是2%,年降雨量在640mm以上的频率是50%。最后采用一维坡地径流模型对南部山区内的典型丘陵的产流量进行了模拟计算,模拟结果和实测值吻合较好。     

Effects of compositional heterogeneity and nanoporosity of raw and treated biomass-generated soot on adsorption and absorption of organic contaminants

A biomass-generated soot was sequentially treated by HCl-HF solution, organic solvent, and oxidative acid to remove ash, extractable native organic matter (EOM), and amorphous carbon. The compositional heterogeneity and nano-structure of the untreated and treated soot samples were characterized by elemental analysis, thermal gravimetric analysis, BET-N₂ surface area, and electron microscopic analysis. Sorption properties of polar and nonpolar organic pollutants onto the soot samples were compared, and individual contributions of adsorption and absorption were quantified. The sorption isotherms for raw sample were practically linear, while were nonlinear for the pretreated-soot. The removal of EOM enhanced adsorption and reduced absorption, indicating that EOM served as a partitioning phase and simultaneously masked the adsorptive sites. By drastic-oxidation, the outer amorphous carbon and the inner disordered core of the soot particles were completely removed, and a fullerene-like nanoporous structure (aromatic shell) was created, which promoted additional π-π interaction between phenanthrene and the soot.     

新型结构ABR的设计与水力特性研究

针对ABR自身的缺点,设计出一种新型结构的ABR.该反应器为双层结构,共有5部分组成,各部分容积各不相同.该反应器的设计思想是将ABR与生物滤池以及活性炭吸附等工艺相联合.这种设计能够最大程度地发挥各工艺的优势,进而达到更好的处理效果.通过脉冲响应实验对该反应器的水力特性进行研究,得出不同水力停留时间(HRT)下的停留...     

污水污泥在富氧环境下燃烧特性的实验研究

采用综合热分析仪研究了空气气氛和富氧气氛下污水污泥和煤的燃烧曲线,分析比较氧浓度对污泥燃烧特性参数的影响,并计算得到各工况下的动力学参数。结果表明：随着氧浓度增加,污泥燃烧DTG曲线向低温区移动,着火温度和燃尽温度均降低,综合燃烧指数大大提高,污泥燃烧特性得到改善。可用两段一级反应动力学模型来较好的描述污泥的主要燃烧过...     

垂直流人工湿地水力学特性研究

通过示踪剂实验从停留时间分布（RTD）曲线及其统计特征值等方面对垂直流人工湿地的水力学特性进行了定性和定量的分析。研究表明水流在垂直流人工湿地中的流动是一种非理想的不均匀流动,存在一定的死区和水流的扩散;垂直流人工湿地较大的死区率与其表面布水的不均匀性有关,这也可能是其死区率大于表流人工湿地的最主要的原因。实验还表明,进水流量对垂直流人工湿地停留时间分布影响较大,随着进水流量的增加,平均停留时间减小,但标准平均停留时间增大,死区率减小;当进水流量为15L／h（水力负荷为620mm／d）时,水流在湿地中的散度最大,水流更接近全混流,不利于污染物的降解。     

Recycling of organic materials and solder from waste printed circuit boards by vacuum pyrolysis-centrifugation coupling technology

Here, we focused on the recycling of waste printed circuit boards (WPCBs) using vacuum pyrolysis-centrifugation coupling technology (VPCT) aiming to obtain valuable feedstock and resolve environmental pollution. The two types of WPCBs were pyrolysed at 600°C for 30 min under vacuum condition. During the pyrolysis process, the solder of WPCBs was separated and recovered when the temperature range was 400-600°C, and the rotating drum was rotated at 1000 rpm for 10 min. The type-A of WPCBs pyrolysed to form an average of 67.91 wt.% residue, 27.84 wt.% oil, and 4.25 wt.% gas; and pyrolysis of the type-B of WPCBs led to an average mass balance of 72.22 wt.% residue, 21.57 wt.% oil, and 6.21 wt.% gas. The GC-MS and FT-IR analyses showed that the two pyrolysis oils consisted mainly of phenols and substituted phenols. The pyrolysis oil can be used for fuel or chemical feedstock for further processing. The recovered solder can be recycled directly and it can also be a good resource of lead and tin for refining. The pyrolysis residues contained various metals, glass fibers and other inorganic materials, which could be recovered after further treatment. The pyrolysis gases consisted mainly of CO, CO(2), CH(4), and H(2), which could be collected and recycled.