生物沥浸处理对城市污泥脱水性能的影响研究

通过摇瓶培养试验研究了生物沥浸处理对城市污泥离心脱水率、污泥过滤比阻、泥饼压缩系数等脱水性能的影响,并分析了生物沥漫过程中污泥Ph、Fe2 、Fe2 、污泥颗粒Zeta电位、粳粒粒径分布的变化.研究表明,以亚铁和硫作为复合能源物质时,污泥经过生物沥浸处理后,其离心脱水率可从原始污泥的60%提高到74.4%;污泥比阻从处理前的1.83×109 s2·g-1下降到0.39×109 s2·g-1,降低了79%,压缩系数也从原始污泥的0.98降低为0.58,明显好于其他处理,达到不加絮凝剂而可直接机械压滤脱水的性能要求.研究还表明,污泥生物沥浸处理后.随着Ph的下降,污泥颗粒Zeta电位趋于零以及污泥20～60μm粒径范围的颗粒含量明显减少,可能是污泥脱水性能改善的重要原因之一.可见,污泥生物沥浸处理是一种在去除重金属的同时能够改善污泥脱水性能的技术.     

污泥中蛋白质和多糖的分布对脱水性能的影响

为研究污泥中蛋白质和多糖的组成及空间分布对污泥可脱水性的影响,采用高温（55℃）及pH 10.0和pH 5.5控制条件,进行污泥水解酸化试验;通过离心和超声波法,对污泥中蛋白质和多糖在污泥粘液层、松散附着胞外聚合物层、紧密粘附胞外聚合物层及细胞相层的分布,并对污泥脱水性能（以毛细吸水时间表征）作了跟踪监测.结果表明,污泥中蛋白质和多糖主要分布在细胞相层.在酸性条件下（pH 5.5）,污泥高温水解酸化（第0～15 d）使其毛细吸水时间比原污泥稍大,而最终（第20 d）稍低;在碱性条件下（pH 10.0）的污泥水解酸化,则使污泥毛细吸水时间远大于原污泥.统计分析结果表明,污泥脱水性能主要受粘液层的可溶性蛋白质和蛋白质/多糖影响,几乎不受污泥中的蛋白质、多糖和蛋白质/多糖及其它EPS层中的化学组分的影响.     

Effect of proteins, polysaccharides, and particle sizes on sludge dewaterability

Four batch experiments of hydrolysis and acidification were carried out to investigate the distributions of proteins (PN) and polysaccharides (PS) in the sludge, the PN/PS ratio, the particle sizes, and their relationship with sludge dewaterability (as determined by capillary suction time, CST). The sludge flocs were stratified through centrifugation- and ultrasound-based method into four fractions: (1) slime, (2) loosely bound extracellular polymeric substances (LB-EPS), (3) tightly bound EPS (TB-EPS), and (4) pellet. The results showed that PN was mainly partitioned in the pellet (80.7%) and TB-EPS (9.6%) fractions, while PS distributed evenly in the four fractions. During hydrolysis and acidification, PN was transferred from the pellet and TB-EPS fractions to the slime fraction, but PS had no significant transfer trends. The mean particle sizes of the sludge flocs decreased with hydrolysis and acidification. The pH had a more significant influence on the dewaterability of sludge flocs than temperature. Sludge dewaterability during hydrolysis and acidification processes greatly deteriorated from 9.7 s at raw sludge to 340–450 s under alkaline conditions. However, it was just slightly increased under acidic conditions. Further investigation suggested that CST was a ected by soluble PN, soluble PN/PS, and particle sizes of sludge flocs, but was a ected slightly by total PN, PS, or PN/PS in the whole sludge flocs and other fractions (except slime).     

Effect of ultrasonic pretreatment on anaerobic digestion and its sludge dewaterability

To investigate the effect of ultrasonic pretreatment on anaerobic digestion and sludge dewaterability and further to probe into the influencing factors on sludge dewaterability, sludge flocs were stratified into four fractions: (1) slime; (2) loosely bound extracellular polymeric substances (LB-EPS); (3) tightly bound EPS (TB-EPS); and (4) EPS-free pellets. The results showed that ultrasonic pretreatment increased the anaerobic digestion efficiency by 7%–8%. Anaerobic digestion without ultrasonic pretreatment deteriorated the sludge dewaterability, with the capillary suction time (CST) increased from 1.42 to 47.3 (sec L)/g-TSS. The application of ultrasonic pretreatment firstly deteriorated the sludge dewaterability (normalized CST increased to 44.4 (sec L)/g-TSS), while subsequent anaerobic digestion offset this effect and ultimately decreased the normalized CST to 23.2 (sec L)/g-TSS. The dewaterability of unsonicated sludge correlated with protein (p = 0.003) and polysaccharide (p = 0.004) concentrations in the slime fraction, while that of sonicated sludge correlated with protein concentrations in the slime and LB-EPS fractions (p < 0.05). Fluorescent excitationemission matrix analysis showed that the fluorescence matters in the LB-EPS fraction significantly correlated with sludge dewaterability during anarobic digestion.     

低温条件下污泥静置沉降时间对城市生物沥浸污泥脱水性能的影响

研究城市生物沥浸污泥脱水性能与污泥静置沉降时间的关系,对城市污泥生物沥浸工程化应用具有指导性作用.因此,以城市生物沥浸污泥为研究对象,研究了低温条件下(5℃和15℃)污泥静置0～6d过程中,污泥pH值和脱水性能(用比阻γ表征)的变化情况.同时,对实验室污泥比阻与厢式压滤机中试结果进行了相关性分析.结果表明:温度增加将有利于污泥沉降,在实际运行中沥浸污泥可选择静置0.5d再进行压滤脱水.随着静置时间的延长,冬季(5℃)和春季(15℃)城市沥浸污泥pH值和比阻均呈逐渐上升的趋势.静置6d后,pH值分别从3.93和3.87上升到5.10和5.32,比阻γ分别从1.72×1012m·kg-1和1.76×1012m·kg-1上升到3.08×1012m·kg-1和5.82×1012m·kg-1.实验室污泥比阻测定和厢式压滤机中试结果表明,不同静置时间下污泥比阻γ与压滤机压滤脱水V-t/V曲线(V:滤液体积;t:过滤时间)斜率k呈极显著正相关关系,说明用污泥比阻γ能准确地反映出生物沥浸污泥的压滤脱水性能.这对生物沥浸技术在工程上的应用和推广具有重要意义.     

不同混凝剂对污泥脱水性能的影响研究

采用无机和有机混凝剂对污泥进行调理,通过测定污泥比阻、Zeta电位以及污泥上清液中蛋白质、多糖和DNA含量,同时结合污泥上清液的三维荧光光谱分析,研究了不同混凝剂及其投加量对污泥脱水性能的影响.结果表明:当聚合氯化铝(PAC)、高效聚合氯化铝(HPAC)和氯化铁(FeCl3)的投加量在干污泥量的10%附近时,污泥比阻值最小,同时三维荧光强度值也最小,Zeta电位以及上清液中蛋白质、多糖和DNA的含量基本趋于稳定.无机混凝剂与有机混凝剂联合作用调理污泥后其脱水效果明显优于单一混凝剂调理.有机混凝剂与无机混凝剂投加顺序对污泥脱水性能影响显著,先投加无机混凝剂再投加有机混凝剂的脱水效果最佳,研究筛选出两种混凝剂联合作用调理污泥后,其脱水效果顺序为10%PAC+0.5%PAM>10%FeCl3+0.5%PAM>10%HPAC+0.5%PAM.     

零价铁活化过一硫酸盐联合单宁酸调理改善市政污泥脱水性能的机理研究

探讨了零价铁（ZVI）活化过一硫酸盐（PMS）联合单宁酸（TA）调理对市政污泥高压压滤深度脱水的影响;通过单因素试验,考察了TA、ZVI和PMS投加量及初始pH值对污泥脱水性能的影响,并深入探究实现污泥深度脱水的潜在机理.结果表明,初始pH值为6.0,ZVI投加量为120 mg·g^-1干污泥量（DS）,PMS投加量为100 mg·g^-1DS,TA投加量为0.06 mmol·L^-1·g^-1DS时,污泥的脱水效果达到最佳,比阻（SRF）和结合水去除率分别高达88.60%和53.17%.经调理联合高压压滤系统处理后,污泥泥饼含水率由89.75%降低至45.17%.进一步研究表明,联合调理实现污泥深度脱水分为3个阶段,包括氧化、絮凝和蛋白质沉淀.最终,ZVI/PMS联合TA调理可大幅提高污泥的脱水性能.该研究结果可为ZVI/PMS联合TA调理技术在市政污泥深度脱水中的应用提供一定的参考价值.     

生物沥浸去除污泥重金属及改善脱水性能研究

从天然矿山酸性废水中富集制备了3种嗜酸性细菌混培物,开展了污泥生物沥浸实验,研究了沥浸去除污泥重金属(Cu、Zn、Cd)同时改善脱水性能的效果.结果表明,3种嗜酸性细菌混培物均可有效去除污泥中的重金属(P<0.01).沥浸12d后,改进型Starkey培养基富集的嗜酸性细菌混培物对Cu和Cd的去除率分别达到82.0%和82.9%,9K培养基富集的嗜酸性细菌混培物进行生物沥浸处理对Zn的去除率可达到87.5%.同时,生物沥浸还可以显著改善污泥的脱水性能(P<0.01).经过12d沥浸,污泥的离心脱水率可由73.1%上升到90.0%.显微观察和能谱分析结果显示,污泥脱水性能的改善是因为生物沥浸能使污泥结构由絮体状变成明显的颗粒状,并可形成以铁、氧和硫为主要元素组成的次生矿物规则晶体.     

絮凝调理对消化污泥的脱水性能及絮体理化特性的影响研究

通过研究厌氧消化污泥(ADS)的絮凝调理过程,分析了阳离子聚丙烯酰胺(CPAM)投药量对ADS的脱水性能与絮体理化特性的影响.结果表明,絮凝调理极大地改善了ADS的脱水性能,毛细吸水时间(CST)从原始污泥的(193.6±0.00)s下降到了最佳投药量下的(5.75±0.21)s,离心上清液粘度从原始污泥的(1.47±...     

芬顿试剂与DDBAC联合调理污泥的工艺优化

研究了不同pH值下芬顿试剂(H2O2/Fe2+)与表面活性剂(DDBAC)联合调理对污泥脱水性能的影响,以污泥滤饼含水率(WC)和毛细吸水时间(CST)作为评价指标进行单因素试验,得出pH值以及药剂投加量最佳范围.然后通过以响应曲面优化法(RSM)为依据的Box-Behnken试验,建立了WC和CST减少率二次多项式预测模型,进而得到各影响因素的最优值.结果表明,联合调理过程中pH=3.91,H2O2、Fe2+和DDBAC的投加量分别为47.60, 38.60, 58.20mg/g时, WC降至60.26%, CST减少率升至89.89%, 污泥脱水性能明显改善.同时,在最优条件下进行了验证试验,试验结果与模型预测值基本吻合,表明基于响应曲面法所得的最佳工艺参数准确可靠,对相关污泥处理及条件优化具有一定的指导意义.