吸附—电化学法组合工艺处理废乳化液

以季铵盐改性硅藻土为吸油剂,采用吸附—电化学组合工艺处理拉丝废乳化液,优化了工艺条件。实验结果表明,在乳化液pH为5.0、吸油剂加入量为20 g/L、反应温度为25 ℃的最优条件下吸附除油15 min,然后在清液pH为8.5、阳极电流密度为4 A/dm²的最优条件下电化学反应4 h后,废水无色无味,COD为43 mg/L,ρ（NH₃-N）=0,ρ（Cu）= 1.6 mg/L,ρ（Zn）= 3.7 mg/L,浊度为1.1 NTU,达到GB 8978—1996污水综合排放标准。     

采用支持向量机算法优化电化学处理油田污水的工艺参数

采用支持向量机(SVM)算法,将Box-Behnken设计法与支持向量回归算法(SVR)实验参数优化软件相结合,优化电化学去除油田污水COD的工艺参数。通过量子粒子群算法对SVM算法参数进行优化,从建立的回归模型中找到工艺参数的全局最佳点:电解时间60 min,电解电流3 A,三维电极填充料中石英砂质量695 g。模型得到的COD理论最优去除率为92.48%,验证实验得到的COD去除率为91.43%。     

Experimental investigation of a solar water distillation-cum-drying unit

In this communication, a new design of solar-energy-based water distillation cum drying unit with parabolic reflector has been designed, fabricated, and tested. Bitter gourd and potato slices are chosen as a drying commodity. Thermal performance of the developed system has been evaluated based on the experimental results and using linear regression analysis. Heat transfer coefficients (convective, evaporative, and radiative) for solar distillation system have been observed to be 2.48–4.09, 13.25–52.38, and 8.75–9.66 W/m²°C, respectively. Overall thermal efficiency and exergy efficiency for the distillation system has been found to be 18.77% and 1.2%, respectively. The convective heat transfer coefficient for potato slices are observed higher for initial hours and decreases as the day progresses. The average convective heat transfer coefficients for bitter gourd and potato slices have been observed as 2.18 and 5.04 W/m²°C, respectively. Experimental error in terms of percent uncertainty for bitter gourd and potato slices are found to be 42.93% and 37.06%, respectively. The present design of solar distillation and drying in a single unit could be beneficial for the development of remote, arid, and rural areas.     

工业烟气氨法-络合法同时脱硫脱硝

在脱硫脱硝喷淋装置上采用氨法-络合法处理工业烟气。考察了吸收液pH、Fe(Ⅱ)EDTA浓度、初始烟气浓度、液气比对烟气同时脱硫脱硝效果的影响。实验结果表明:吸收液的酸碱度通过影响Fe(Ⅱ)与EDTA的络合形式进而影响NO去除率;SO_2去除率主要受吸收液pH和初始SO_2质量浓度的影响;当吸收液pH大于8、吸收液Fe(Ⅱ)EDTA浓度大于0.100 mol/L、初始SO_2质量浓度小于1 500 mg/m3、初始NO质量浓度为1 200 mg/m3时,SO_2去除率均在95%以上,NO去除率为54%;当液气比由1 L/m3增大至4 L/m3时,有效脱硫时间和有效脱硝时间分别增长了7 min和4 min。     

废弃印刷线路板碘化法浸金研究

针对碘化法从废弃印刷线路板中提取金的工艺设计,分别考察了碘的质量分数、n(I₂)/n(I^-)比值、固液比、双氧水的质量分数、pH值、浸出时间和浸出温度对金浸出率的影响。结合正交设计优化实验方法,提出了从废弃印刷线路板中碘化法浸取金的最佳工艺条件：碘的质量分数为1.1％,n(I₂)∶n(I^-)=1∶10,双氧水的质量分数为1.5％,浸出时间4 h,固液比为1∶10,浸出温度为常温（25℃）,溶液pH值为中性,此时金浸出率可达97.5％。     

基于生态安全的DAT-IAT城市污水处理工艺改进研究

通过正交试验,得到了DAT-IAT工艺和A/DAT-IAT工艺处理城市污水的常规指标去除和生态毒理指标削减的最优运行条件。结果表明,在正交试验的同一工艺中,COD去除最优运行条件的出水COD值优于生态毒性削减最优运行条件的出水COD值,但前者出水的生态毒性较大。由于厌氧池的水解酸化作用,A/DAT-IAT工艺对COD和生态毒性的处理效果均优于DAT-IAT工艺,并且回流总能耗低于DAT-IAT工艺,但是出水COD仍不达标。为了降低进入工艺的COD的总量,以絮凝沉淀做为预处理工艺,并采用Al残留量最小的絮凝剂投药量以降低出水中残留Al带来的生态风险。结果表明,在COD去除最优运行条件下,具有絮凝预处理的工艺对COD的去除效果优于没有絮凝预处理的工艺。絮凝-A/DAT-IAT工艺在COD去除最优运行条件下出水COD为104.46 mg/L,满足排放标准。在毒性削减最优运行条件下,具有絮凝预处理的工艺的出水生态毒性有所上升,但是污染物的总量得到了大幅削减。絮凝-A/DAT-IAT工艺与DAT-IAT工艺相比,在污染物去除效率得到大幅增加的同时,生态毒性得到有效控制,生态安全得到了有效的保障。     

微曝气Fenton氧化法处理模拟双酚A废水的效果及其生物验证

研究了微曝气Fenton氧化法关键工艺参数对模拟双酚A（BPA）废水处理效果的影响,并从活性污泥性质和污染物去除率两方面,采用膜生物反应器(membrane bioreactor, MBR)对微曝气Fenton氧化法的处理效果进行了实验验证,为实现BPA废水的生物处理奠定基础。结果表明,初始pH值、反应时间、H₂O₂/COD(质量浓度比)、H₂O₂/Fe²⁺ (摩尔浓度比)、反应温度及曝气量均对预处理效果有较大影响,在最佳条件下,COD去除率可达70%,BOD/COD值则由原废水的0.02提高到0.50以上。MBR处理上述出水的结果表明,经微曝气Fenton氧化处理BPA的废水,可较好地适应后续的生化处理。     

基于超临界水氧化过程的能源环境系统设计

阐述了超临界水氧化过程的工艺路线,介绍了超临界水氧化过程的特点,提出了基于超临界水氧化过程的能源环境系统,设计了几种热量与能量回收系统程的耦合工艺,为提高超临界水氧化过程的经济性奠定了基础。     

太阳光Fenton法处理垃圾渗滤液中有机污染物

研究利用太阳光Fenton法处理垃圾渗滤液。根据太阳光辐射强度随时间的变化规律,选择重庆7、8月份的晴天,在中午12：00到下午14：00时进行试验,研究太阳光辐射时间、pH值、Fenton试剂用量对垃圾渗滤液COD去除率的影响。研究结果表明：太阳光Fenton法对垃圾渗滤液的COD有较好的去除效果,COD去除率达86.2%。太阳光Fenton法处理垃圾渗滤液的优化条件是：日光辐射时间为120 min,pH值为2.5,Fe²⁺浓度为5 mmol/L,H₂O₂浓度为570 mmol/L。同时,论文还对太阳光Fenton法处理垃圾渗滤液的动力学进行分析。研究结果显示：太阳光Fenton法处理垃圾渗滤液,其表观动力学方程为-dC/dt=2.6×10^-8×P^1.92×F^1.79×E^1.67。     

Landfill site selection using spatial information technologies and AHP: A case study in Beijing,China

Site selection is an important and necessary issue for waste management in fast-growing regions. Because of the complexity of waste management systems, the selection of the appropriate solid waste landfill site requires consideration of multiple alternative solutions and evaluation criteria. Based on actual conditions of the study area, we considered economic factors, calculated criteria weights using the analytical hierarchy process (AHP), and built a hierarchy model for solving the solid waste landfill site-selection problem in Beijing, China. A geographic information system (GIS) was used to manipulate and present spatial data. All maps are graded from 1 (lowest suitability) to 5 (highest suitability) using spatial information technologies. The candidate sites were determined by aggregation based on the criteria weights. The candidate sites are divided by ‘best’, ‘good’ and ‘unsuitable’ landfill areas. Best landfill areas represent optimal sites; good landfill areas can be used as back-up candidate sites. Our work offers a siting methodology and provides essential support for decision-makers in the assessment of waste management problems in Beijing and other rapidly developing cities in developing countries.