Formic acid as an alternative reducing agent for the catalytic nitrate reduction in aqueous media

Formic acid was used for the nitrate reduction as a reductant in the presence of Pd:Cu/γ-alumina catalysts. The surface characteristics of the bimetallic catalyst synthesized by wet impregnation were investigated by SEM, TEM-EDS. The metals were not distributed homogeneously on the surface of catalyst, although the total contents of both metals in particles agreed well with the theoretical values. Formic acid decomposition on the catalyst surface, its influence on solution pH and nitrate removal efficacy was investigated. The best removal of nitrate (50 ppm) was obtained under the condition of 0.75 g/L catalyst with Pd:Cu ratio (4:1) and two fold excess of formic acid. Formic acid decay patterns resembled those of nitrate removal, showing a linear relationship between kf (formic acid decay) and k (nitrate removal). Negligible amount of ammonia was detected, and no nitrite was detected, possibly due to buffering effect of bicarbonate that is in situ produced by the decomposition of formic acid, and due to the sustained release of H2 gas.     

Electrochemical and spectroscopic characteristics of dissolved organic matter in a forest soil profile

Dissolved organic matter （DOM） represents one of the most mobile and reactive organic compounds in ecosystem and plays an important role in the fate and transport of soil organic pollutants, nutrient cycling and more importantly global climate change. Electrochemical methods were first employed to evaluate DOM redox properties, and spectroscopic approaches were utilized to obtain information concerning its composition and structure. DOM was extracted from a forest soil profile with five horizons. Differential pulse voltammetry indicated that there were more redox-active moieties in the DOM from upper horizons than in that from lower horizons. Cyclic voltammetry further showed that these moieties were reversible in electron transfer. Chronoamperometry was employed to quantify the electron transfer capacity of DOM, including electron acceptor capacity and electron donor capacity, both of which decreased sharply with increasing depth. FT-IR, UV-Vis and fluorescence spectra results suggested that DOM from the upper horizons was enriched with aromatic and humic structures while that from the lower horizons was rich in aliphatic carbon, which supported the findings obtained by electrochemical approaches. Electrochemical approaches combined with spectroscopic methods were applied to evaluate the characteristics of DOM extracted along a forest soil profile. The electrochemical properties of DOM, which can be rapidly and simply obtained, provide insight into the migration and transformation of DOM along a soil profile and will aid in better understanding of the biogeochemical role of DOM in natural environments.     

LNAPLs污染物在层状非均质多孔介质中的运移试验研究

文章通过室内试验研究层状非均质多孔介质中轻非水相液体(Light Non-Aqueous Phase Liquid,LNAPL)的运移机制与分布特性。首先,在二维砂槽上进行LNAPL的入渗试验,试验过程中用数码相机进行拍照,把LANPL的扩散过程以图像的形式记录下来;然后,用AutoCAD对图片进行分析处理,得出不同时刻LNAPL的入渗锋面变化图。结果发现,介质结构突变面改变了LNAPL的迁移模式。在LNAPL由中砂进入细砂层后,由于受到毛细作用的增强,其运移速度加快;而由中砂进入粗砂,受粗砂介质阻滞作用增强的影响,LNAPL运移速度变小。当LNAPL由干砂进入湿润砂体时,由于孔隙水浮托力增大,LNAPL先产生纵向运移,随后以横向迁移的形式在地下水位上部聚积。当达到一定厚度后,LNAPL的压头足以克服浮托力,驱替孔隙水进入砂土孔隙。另外,LNAPL的厚度足够大时,方可克服饱水层受到的浮托力,在地下水位上形成LNAPL池,并因孔隙水向周围砂体排泄,LNAPL池周围的水位上升。     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

非均相类Fenton试剂的制备及其在焦化废水处理中的应用研究

利用浸渍法,将Fe3＋负载在经酸碱改性后的粉状活性炭上,当浸渍液浓度为2．5％,固化温度为270℃时,制成的催化剂催化活性较高。用自制的非均相类benton试剂降解焦化废水,通过正交试验和极差分析得出,影响因素的主次顺序为催化剂用量〉初始pH值〉反应时间〉H：0：投加量。结果表明,在100ml水样中。室温条件下,初始pH值为4．0,催化剂使用量为1．5g,H20：投加量为5ml（分两次投加）,反应时间为90min时,COD去除率可达99％。采用混凝＋化学沉淀＋非均相类Fenton试剂法处理焦化废水,各主要出水水质指标为：色度lO倍;COD浓度38．5mg／L;氨氮浓度8．4mg／L,达到国家一级排放标准。     

电化学强化低能耗废水生物处理技术研究

以碳布为阴阳极材料构建一种新型的生物电化学系统（BES）,研究该系统在不曝气条件下对城市污水的处理效果,并与传统的厌氧和好氧处理方法进行比较。结果表明,该BES处理城市污水是可行的,与传统曝气法相比能够显著降低能耗。在进水CODcr,为350mg／L、NH3-N为15mg／L、水力停留时间（HRT）为24h时,电化学强化生物处理系统对CODcr和NH3-N的去除率达84％和80％,优于同等条件下的厌氧、好氧生物处理方法。BES的输出电压最高为211mV。     

氧气热处理的TiO2纳米管阵列光电催化降解亚甲基蓝的研究

采用原位阳极氧化法在Ti基底上制备了高度有序的TiO2纳米管阵列薄膜,SEM图像表明TiO2纳米管定向排列整齐,分布均匀,其管径范围在70～100 nm.XRD结果证明,阳极氧化法制备的TiO2纳米管为无定型晶型,经退火后为具有良好光催化活性的锐钛矿型.以亚甲基蓝（methylene blue）为目标物研究了TiO2纳米管光电催化性能及影响因素,结果表明,以0.1 mol/L NaCl为电解质,在氧气热处理气氛下,外加偏压为0.5 V、pH=3.25、光照强度为1 000μW/cm2、纳米管薄膜表面积为2 cm×2 cm且MB初始浓度为10 mg/L的条件下,TiO2纳米管阵列薄膜光电催化降解MB的降解效率可达99.56%.电化学阻抗谱分析显示,光电催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

几种牺牲阳极在干湿交替条件下的自放电行为比较

模拟海水与空气的干湿交替条件,对四种海船常用牺牲阳极的自放电行为进行了研究。通过测定工作电位、发生电流、溶解性能、溶解产物成分,分析了四种牺牲阳极在经历不同间浸工作周期后的电化学性能,特别是再活化性能。结果表明:在干湿交替条件下,Zn-Al-Cd阳极的电化学性能降低幅度最大,Al-Zn-In-Cd阳极次之,它们均不适合在此环境中使用;Al-Zn-In-Mg-Ti的电化学性能比前两者好,Al-Zn-In-Mg-Ga-Mn则最适合作为干湿交替环境中的牺牲阳极。     

铁阳极电解脱色直接黄11染料模拟废水

研究采用铁为阳极电化学法处理直接黄11染料模拟废水脱色性能的影响进行研究。影响因素包括:电流密度、pH值、染料浓度和电解质浓度。研究结果表明,电流密度大有利于染料废水脱色,但能耗消耗大;初始溶液在中性条件下不仅取得很好的处理效果,而且脱色能耗较低;随着染料初始浓度增加脱色率和脱色能耗降低的趋势;随着电解质浓度升高染料脱色率下降的趋势,脱色能耗先减少,然后缓慢增大。在染料初始浓度50 mg/L、pH值为7.11、电流密度2.083 mA/cm2、电解质Na2SO4浓度0.01 mol/L、温度20℃、搅拌速度600 r/min、电解时间60min条件下,脱色率达到92.2%,脱色能耗1.709 kW.h/kg染料。