一种新型电化学法处理硝态氮废水的初步研究

通过对Pd-Me双金属催化还原NO 3--N和折点氯化法处理NH 4+-N的相关理论分析,提出了一种基于电化学法的新型NO 3--N废水处理工艺.即利用具有电子空轨的常见金属元素修饰Ti基获得催化阴极,在电场的作用下,将NO 3--N催化还原;通过调整催化元素的配比和电解条件,控制NO 3--N还原产物主要为NH 4+-N;利用阳极氧化Cl-生成高氧化性物质HOCl,将NH 4+-N氧化为无害产物N2-N.结果表明,金属元素Co和Cu修饰Ti基制得阴极可以有效地催化还原模拟废水中的NO 3--N;按前驱物溶液金属元素摩尔比1∶1制得Ti基Co-Cu复合涂层催化阴极,可以将NO 3--N高效催化还原为NH 4+-N;电解体系中引入Cl-后,通过阳极作用可将NO 3--N还原生产的NH 4+-N有效地氧化为N2-N.在100 mg/L NO 3--N模拟废水中添加1 000 mg/L Cl-,设置极板间距6 mm、电流400 mA,电解2.5 h后出水NO 3--N、NO 2--N、NH 4+-N和TN分别为2.9、0.5、1.7和6.0 mg/L.     

ZnOOH/O3催化臭氧化体系去除水中痕量对氯硝基苯

以实验室制备的羟基化锌（ZnOOH）为催化剂,考察了其催化臭氧化去除水中痕量对氯硝基苯（ppCNB能力.本实验条件下,蒸馏水中反应20　min时,催化臭氧化比单独臭氧化对pCNB的去除率提高了51 .3个百分点;催化过程遵循自由基反应机理,催化剂表面结合的羟基基团有利于催化反应;pCNB的去除效果随催化剂投量的增加而更佳,催化剂重复使用3次后,催化效果基本没有变化,水中的重碳酸盐以及缓冲溶液中的磷酸盐可以明显降低催化活性,中性条件下,催化作用最佳.     

纳米TiO2催化臭氧化对松花江水中氨氮的影响

研究了以负载于陶粒、硅胶、沸石表面的纳米TiO₂作为催化剂时,催化臭氧化松花江水过程中氨氮浓度的变化.结果表明,在单独臭氧化过程中,氨氮浓度先升高后下降,反应30 min后的氨氮浓度与初始浓度相近.在以TiO₂/陶粒、TiO₂/硅胶为催化剂的催化臭氧化过程中,氨氮浓度也是先升高后下降,但反应过程中氨氮的平均浓度要高于单独臭氧化过程.以TiO₂/沸石为催化剂时,催化臭氧化过程中氨氮浓度先下降,然后略有升高,继而又下降,30 min时对氨氮的去除率接近80%.单独臭氧化和催化臭氧化过程中,增大臭氧投量,氨氮浓度最大值出现的时间提前,并且反应过程中氨氮浓度平均值降低.增大催化剂TiO₂/陶粒、TiO₂/硅胶的投量,催化臭氧化过程中氨氮浓度平均值升高.增大TiO₂/沸石投量,有利于氨氮的去除,但投量增大到50g以上时,对氨氮的去除效果影响很小.温度从10℃升高到30℃,对TiO₂/陶粒、TiO₂/硅胶催化臭氧化过程中氨氮浓度的变化影响不大.而以TiO₂/沸石为催化剂时,温度升高有利于催化臭氧化过程中氨氮的去除.     

催化剂Ru/ZrO2-CeO2催化湿式氧化苯酚

催化剂Ru/ZrO₂-CeO₂催化湿式氧化苯酚的过程表明,Ru/ZrO₂-CeO₂可以显著提高COD和苯酚去除效果,当反应温度为170℃,压力为3 MPa,反应120 min后,COD和苯酚的去除率分别达到了99％和100％.试验还考察了不同反应条件对苯酚溶液COD去除的影响,并获得了最优的反应条件：温度为170℃,压力为3 MPa,催化剂的投加量为5　g/Ｌ,搅拌速度为500 r/min.通过对中间产物的分析,本研究提出了催化湿式氧化苯酚的简单路径图,认为苯酚首先被氧化成小分子有机酸,接着小分子有机酸被氧化成二氧化碳和水.前一个过程是快速反应,后一个过程中的乙酸氧化是慢速过程,需要在高温下才能完成.乙酸的氧化主要是自由基攻击α碳上的C—H键,先生成甲酸,并最终生成二氧化碳和水.     

Kinetics of selective catalytic reduction of NO by NH3 on Fe-Mo/ZSM-5 catalyst

The catalyst of Fe-Mo/ZSM-5 has been found to be more active than Fe-ZSM-5 and Mo/ZSM-5 separately for selective catalytic reduction (SCR) of nitric oxide (NO) with NH3. The kinetics of the SCR reaction in the presence of O2 was studied in this work. The results show that the observed reaction orders were 0.74-0.99, 0.01-0.13, and 0 for NO, O2 and NH3, respectively, at 350-450℃. And the apparent activation energy of the SCR was 65 kJ/mol on the Fe-Mo/ZSM-5 catalyst. The SCR mechanism was also deduced. Adsorbed NO species can react directly with adsorbed ammonia species on the active sites to form N2 and H2O. Gaseous O2 might serve as a reoxidizing agent for the active sites that have undergone reduction in the SCR process. It is also important to note that a certain amount of NO was decomposed directly over the Fe-Mo/ZSM-5 catalyst in the absence of NH3.     

Pd/C气体扩散电极用于电生成H2O2降解苯酚的研究

采用自制的Pd/C气体扩散阴极和Ti/IrO2/RuO2阳极,在无隔膜电解槽中对苯酚模拟废水降解效果及机制进行了研究,采用电子自旋共振法(ESR)对电解体系中产生的羟自由基(·OH)进行了检测.结果表明,在Pd/C气体扩散体系中掺杂Pd催化剂可以促进H2 O2的生成(H2 O2的稳定浓度是7.5 mg/L),有利于·OH的产生.经电化学氧化处理120 min后,苯酚和COD的去除率分别达到97.2%和50%,表明在电催化氧化过程中苯酚被氧化生成了大量低分子量中间产物.废水的BOD5/COD值达到0.73是处理前的9.1倍,苯酚废水的可生化降解性通过电化学氧化处理后显著提高.在该电化学体系中苯酚的降解是在阳极直接、间接氧化及阴极产生的H2 O2、·OH的氧化共同作用下完成的.通过对紫外扫描光谱图的分析推断出苯酚在电解过程中有醌类物质生成;由GC-MS检测到了邻苯二酚、对苯二酚、苯醌等芳香族化合物和己二酸、顺丁烯二酸、反丁烯二酸、丁二酸、丙二酸、乙二酸等短链羧酸,据此提出了苯酚降解的可能历程.     

非均相催化臭氧处理高浓度制药废水的研究

非均相催化臭氧是一种对高浓度制药废水进行预处理的有效方法.本研究采用单一活性炭吸附、单一臭氧氧化和臭氧/活性炭联用3种体系对实际制药废水进行预处理,并对处理过程中的工艺参数进行优化.结果表明,相比单一活性炭吸附和单一臭氧降解体系,臭氧/活性炭联用体系能显著提高COD、TOC的去除率及BOD5/COD值,并显示出良好的协...     

电渗析法再生CO_2电还原电解液的研究

探索了电渗析法再生CO2电还原电解液的可行性。以HCOOK溶液作为CO2电还原反应后的模拟液,采用单室电渗析装置对其进行再生,考察了电流、时间、温度等操作条件对电流效率和再生率的影响,研究结果表明:在常温条件下,操作电流低于极限电流时,采用电渗析法再生CO2电还原电解液具有高的电流效率和再生率。     

Effect of manufacturing methods of AgCl/Al2O3 catalyst on selective catalytic reduction of NOx

The AgCl/Al2O3 catalyst has potential for use in the selective catalytic reduction (SCR) of NOx. A compound hydrocarbon, following oxygenation is used as a type of reducing agent. In this experiment, the AgCl/Al2O3 catalyst was produced by four different methods, and the differences among their reduction catalysis of NOx were compared. Ethanol was used as a type of reducing agent. X-ray diffraction analysis was performed to study the crystalline structure and scanning electron microscope and transmission electron microscope (TEM) were applied to determine the microindentation. The results indicated that, in the range of 350–400°C, there was no significant difference on the NOx reduction rate; however, there was dispersion at high and low temperature ranges. The size of the AgCl particles was about 20–100 nm.     

Complete catalytic oxidation of o-xylene over Ce02 nanocubes

The activities of CeO2 nanocubes calcined at different temperatures were tested for catalytic oxidation of o-xylene. Using CeO2 nanocubes as catalysts, complete catalytic oxidation of o-xylene was achieved below 210℃. The CeO2 nanomaterials were characterized by means of BET, X-ray diffraction (XRD), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). From the TEM images, all Ce02 nanocubes displayed cubic morphology irrespective of calcination temperature. The HRTEM images revealed that these nanocubes were enclosed by reactive {001}planes, which may contribute to the intrinsically catalytic property of o-xylene oxidation. The higher activity of Ce02 nanocubes calcined at 550℃ than those calcined at above 550℃ was attributed to their smaller crystallite size and larger surface area. The influences of reaction conditions were also studied, which found that a higher reaction temperature was necessary for complete catalytic oxidation of o-xylene at higher weight hourly space velocity (WHSV) and o-xylene concentration.