北京不同污染事件期间气溶胶光学特性

利用2005~2011年的AERONET观测数据,对北京不同污染事件期间(秸秆焚烧、烟花燃放以及沙尘天气)气溶胶光学特性进行了分析.气溶胶光学厚度受污染有显著上升,沙尘、秸秆、烟花气溶胶的AOD440 nm分别是干净背景的4.91、4.07、2.65倍.AOD与ngstrm波长指数的匹配能够较好地识别污染类型,沙尘对应高AOD和低α,烟花气溶胶α(1.09)稍低于秸秆(1.21)以及背景(1.27),表明烟花气溶胶的粗粒子更占优,秸秆对应更高的AOD则与其中黑碳颗粒较强的消光能力有关.单次散射反照率对波长敏感性不高,沙尘气溶胶的ω值(0.934)高于背景值(0.878)、秸秆气溶胶(0.921)以及烟花气溶胶(0.905),秸秆气溶胶受烟羽老化、吸湿性增长等影响表现出偏大现象.气溶胶粒子谱分布在背景与污染期间均为双峰模态,细模态和粗模态的峰值浓度半径分别为0.1~0.2μm以及2.24~3.85μm,粗细粒子浓度比值由小到大依次为背景(1.04)、秸秆焚烧(1.10)、烟花燃放(1.91)以及沙尘气溶胶(4.96).     

苦草(Vallisneriaspiralis)对城市缓流河道黑臭底泥理化性质的影响

以苦草(Vallisneria spiralis)和城市缓流河道黑臭底泥为研究对象采用模拟实验方法,探讨了苦草对城市缓流河道黑臭底泥理化性质的影响.结果表明,苦草可以显著改善城市缓流污染河道底泥氧化还原环境.实验期间表层底泥Eh从-70 mV升高至90 mV;减少致黑物质亚铁的含量,实验组表层底泥降低25%,而对照却升高38%;促进铁、硫的自然循环,防止亚铁、H2S的累积;明显改善底泥黑臭现象,实验组表层底泥第7 d出现约3 mm厚灰黄色氧化层,氧化层随时间推移逐渐增厚,第28 d厚度为11 mm.该氧化层无明显恶臭气味.对照则在实验第14 d出现1 mm氧化层并维持至实验结束,期间恶臭气味未消减;种植苦草可显著提高沉积物致密程度,降低底泥含水率,有效改善表层底泥流动状态,且在段头浜、河湾、人工湿地景观等处不影响防汛等功能,对减少河道底泥冲刷迁移和抑制黑臭物质悬浮具有积极的生态学意义.     

磺胺甲噁唑对猪粪堆肥过程中堆料性质与酶活性的影响

以猪粪、小麦秸秆为材料,研究了磺胺甲噁唑（SMZ）对高温堆肥过程中理化性质（温度、pH值、E₄/E₆）和酶活性（纤维素酶、磷酸酶、脲酶、多酚氧化酶）的影响.结果表明：SMZ对堆肥理化性质的影响与其浓度有关.高浓度（95 mg·kg^-1）SMZ会对微生物活性产生显著抑制作用,表现出堆肥温度难以达到无害化标准,堆料pH值较低（<9.0）.但高浓度（95 mg·kg^-1）SMZ能激活多酚氧化酶活性,且水提浸液E₄/E₆值较低.在堆肥过程中,SMZ对纤维素酶和脲酶活性呈现出“抑制-激活-抑制”的作用,50 mg·kg^-1的SMZ对纤维素酶产生不同程度的激活作用.相比之下,脲酶活性对SMZ的敏感性比纤维素酶更敏感,5 mg·kg^-1的SMZ即能显著抑制脲酶活性,中浓度（50 mg·kg^-1）的SMZ对碱性磷酸酶活性产生了显著的抑制作用.综上,SMZ通过影响酶活性而影响堆肥过程的物质转化.此外,SMZ浓度越大,种子发芽指数越低.当SMZ≥50 mg·kg^-1时,堆肥难以腐熟而对植物毒性较大.     

改性壳聚糖CAD与微生物絮凝剂MBF8复配絮凝研究

采用水溶液自由基聚合反应,将丙烯酰胺(AM)、二甲基二烯丙基氯化铵(DMDAAC)接枝到壳聚糖分子上制成了阳离子改性壳聚糖(CAD).经FT-IR、XRD、zeta(ξ)电位、凝胶色谱等分析确定,CAD为淡黄色透明液体,pH值为3.7,相对分子质量为2.88×10⁶,阳离子度为16.7,等电点(0.1%溶液)约为pH值10.5,有效成分2.6%,主要特征官能团有羟基、氨基、季铵基和酰胺基, 呈不规则晶体结构.将CAD与相对分子质量3.67×10⁵的多糖类电负性微生物絮凝剂MBF8复配,对浊度12~460 NTU、离子强度3.0 mmol·L^-1的高岭土悬浊液进行烧杯实验.结果表明,MBF8与CAD的最佳使用方式为先投加MBF8后投加CAD,复配比5:3时效果最好,适用的pH范围为6.0~10.0.采用PAC(3.0 mg·L^-1)+MBF8+CAD(1.0 mg·L^-1)复配絮凝,pH=8.0下,对浊度为110 NTU的高岭土悬浊液,浊度去除率>97%,残余铝<0.08 mg·L^-1,絮体大、沉降快,絮凝效果优于PAC+分子量800万、1200万的阴离子PAM及分子量1500万的阳离子PAM.     

有序介孔碳载金/L-赖氨酸/纳米金修饰电极的制备及其对邻苯二酚、对苯二酚的检测响应研究

通过化学还原的方法合成有序介孔碳负载纳米金粒子,并构筑有序介孔碳载金/L-赖氨酸/纳米金复合膜修饰玻碳电极;利用扫描电镜观察介孔碳和介孔碳复合膜的微观结构,并用循环伏安法、电化学阻抗谱表征自组装电极的过程.在此基础上用差分脉冲伏安法研究对苯二酚和邻苯二酚混合物在该电极上的电催化氧化,研制了一种基于有序介孔碳载金/L-赖氨酸/纳米金复合膜修饰电极分别检测对苯二酚和邻苯二酚的传感器.在最优的实验条件下,该传感器在对苯二酚和邻苯二酚浓度为1×10-6～8×10-4mol·L-1的范围内具有良好的线性关系,检出限分别为3×10-7mol·L-1、7×10-7mol·L-1.     

Electrochemical and spectroscopic characteristics of dissolved organic matter in a forest soil profile

Dissolved organic matter （DOM） represents one of the most mobile and reactive organic compounds in ecosystem and plays an important role in the fate and transport of soil organic pollutants, nutrient cycling and more importantly global climate change. Electrochemical methods were first employed to evaluate DOM redox properties, and spectroscopic approaches were utilized to obtain information concerning its composition and structure. DOM was extracted from a forest soil profile with five horizons. Differential pulse voltammetry indicated that there were more redox-active moieties in the DOM from upper horizons than in that from lower horizons. Cyclic voltammetry further showed that these moieties were reversible in electron transfer. Chronoamperometry was employed to quantify the electron transfer capacity of DOM, including electron acceptor capacity and electron donor capacity, both of which decreased sharply with increasing depth. FT-IR, UV-Vis and fluorescence spectra results suggested that DOM from the upper horizons was enriched with aromatic and humic structures while that from the lower horizons was rich in aliphatic carbon, which supported the findings obtained by electrochemical approaches. Electrochemical approaches combined with spectroscopic methods were applied to evaluate the characteristics of DOM extracted along a forest soil profile. The electrochemical properties of DOM, which can be rapidly and simply obtained, provide insight into the migration and transformation of DOM along a soil profile and will aid in better understanding of the biogeochemical role of DOM in natural environments.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

电化学强化低能耗废水生物处理技术研究

以碳布为阴阳极材料构建一种新型的生物电化学系统（BES）,研究该系统在不曝气条件下对城市污水的处理效果,并与传统的厌氧和好氧处理方法进行比较。结果表明,该BES处理城市污水是可行的,与传统曝气法相比能够显著降低能耗。在进水CODcr,为350mg／L、NH3-N为15mg／L、水力停留时间（HRT）为24h时,电化学强化生物处理系统对CODcr和NH3-N的去除率达84％和80％,优于同等条件下的厌氧、好氧生物处理方法。BES的输出电压最高为211mV。     

氧气热处理的TiO2纳米管阵列光电催化降解亚甲基蓝的研究

采用原位阳极氧化法在Ti基底上制备了高度有序的TiO2纳米管阵列薄膜,SEM图像表明TiO2纳米管定向排列整齐,分布均匀,其管径范围在70～100 nm.XRD结果证明,阳极氧化法制备的TiO2纳米管为无定型晶型,经退火后为具有良好光催化活性的锐钛矿型.以亚甲基蓝（methylene blue）为目标物研究了TiO2纳米管光电催化性能及影响因素,结果表明,以0.1 mol/L NaCl为电解质,在氧气热处理气氛下,外加偏压为0.5 V、pH=3.25、光照强度为1 000μW/cm2、纳米管薄膜表面积为2 cm×2 cm且MB初始浓度为10 mg/L的条件下,TiO2纳米管阵列薄膜光电催化降解MB的降解效率可达99.56%.电化学阻抗谱分析显示,光电催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

几种牺牲阳极在干湿交替条件下的自放电行为比较

模拟海水与空气的干湿交替条件,对四种海船常用牺牲阳极的自放电行为进行了研究。通过测定工作电位、发生电流、溶解性能、溶解产物成分,分析了四种牺牲阳极在经历不同间浸工作周期后的电化学性能,特别是再活化性能。结果表明:在干湿交替条件下,Zn-Al-Cd阳极的电化学性能降低幅度最大,Al-Zn-In-Cd阳极次之,它们均不适合在此环境中使用;Al-Zn-In-Mg-Ti的电化学性能比前两者好,Al-Zn-In-Mg-Ga-Mn则最适合作为干湿交替环境中的牺牲阳极。