宝钢焦化废水处理脱氮研究与实践

针对上海提高新排放标准中总氮(TN)≤35 mg/L的要求,对焦化废水进行了脱氮研究。选取现场缺氧-好氧-好氧(A-O-O)工艺中前两段的A-O生化沉淀池1出水,在SBR内进行反硝化脱氮实验,考察葡萄糖、葡萄糖+乙酸钠、甲醇和甲醇+乙酸钠单一或复合碳源及投加反硝化菌种对脱氮的影响,确定最佳碳源为甲醇+乙酸钠,最佳反硝化水力停留时间为16 h。当反硝化菌液投加浓度为1 mg/L时,SBR出水TN满足达标排放要求。结合实验结果对宝钢焦化废水原有AO-O工艺改造升级为A-O-A-O二段脱氮工艺,并对生化出水实施进一步的物化混凝处理。改造后,工艺长期运行稳定,最终出水完全达到上海市污水综合排放标准(DB 31/199-2009)TN≤35 mg/L的要求,并满足氰化物、氟化物以及COD的排放要求。     

超声破解污泥上清液对A~2O工艺脱氮除磷和微生物群落结构的影响

为了提高传统污水处理工艺的脱氮除磷效率、实现污泥资源化,本实验通过超声破解污泥获取碳源,采用耗氧呼吸速率分析上清液作为碳源的可行性,并将上清液回用于生活污水,考察其对A2O工艺长期运行的脱氮除磷效果和微生物群落结构的影响。结果表明,上清液中可降解有机物达到76.2%,具有作为内碳源的潜能;上清液和生活污水按1∶15投入A2O反应器后,氮、磷的去除率分别从63.2%和53.4%提高到了82.1%和94.7%;上清液明显改变了微生物群落结构,使除磷菌Actinobacteia和反硝化聚磷菌Sphingobacterium富集。     

利用白云石石灰去除与回收污泥厌氧消化液中氮和磷

以白云石石灰为实验材料去除与回收污泥厌氧消化液中的氮磷,通过小试实验研究不同投药固液比S/L、初始pH值、反应温度、搅拌速度及反应时间对去除与回收氮磷效果的影响。实验结果表明,在最佳投药固液比S/L为300mg/L,最佳初始pH值范围为8.5~9.5,反应温度为25.0℃,搅拌速度为150 r/min,反应时间为24 h条件下,氨氮(NH+4-N)和磷(PO3-4-P)的去除率分别为37.26%和89.60%。利用X射线衍射仪(XRD)、扫描电镜(SEM)对沉淀产物进行了表征,通过分析可知沉淀产物中含有磷酸铵镁(MAP),可实现废水中氮磷经济有效的回收。     

酸性矿井水中和沉淀法除铁优化

针对山西某煤矿高矿化度、高铁酸性矿井水除铁效果差、出水容易返色等问题,采用NaOH中和调pH、曝气及化学氧化等处理工艺进行酸性矿井水中和沉淀法除铁优化实验研究。结果表明,采用NaOH中和沉淀法除铁时,投加中和剂使出水pH达6.7以上时,出水中铁含量低于10 mg/L,满足排放要求。对于本实验废水NaOH所需投加量为2.8 g/L,铁的去除率可达到99.75%;以H2O2对原水进行氧化处理,可迅速将Fe(Ⅱ)氧化成Fe(Ⅲ),其用量与原水中Fe(Ⅱ)的含量成正比。当其用量为1.6 mL/L时,可将原水中的Fe(Ⅱ)完全转化为Fe(Ⅲ),投加中和剂使出水pH达到4.5以上时,能使出水中铁含量满足排放要求。对于实验废水所需的NaOH投加量为2.0 g/L,比直接中和沉淀所需的NaOH用量要节省28.6%。曝气处理对原水中Fe(Ⅱ)的氧化效果不明显。     

氧活性粒子氧化NO生成HNO_3

采用强电离介质阻挡放电方法制取高浓度氧活性粒子(O+2、O3)并注入气体外排烟道中,实现O+2、O3氧化NO转化成资源酸(HNO3)的等离子化学反应。描述强电离放电的氧活性粒子产生器,讨论烟道中O+2、O3氧化NO成HNO3等离子体反应机制,分析回收酸液的NO-2、NO-3离子种类及浓度。考察强电离放电等离子体源的输入功率、水体积百分比、气体温度、气体流速对NOx氧化率的影响。氧化率为97.2%的最佳实验条件是:O+2浓度为1.38×1010个/cm3,O3浓度为210 mg/L,烟气温度为65℃,H2O体积浓度为5.6%,停留时间为0.94 s。     

抗铬菌株的筛选鉴定及其生物学特性和吸附特性

利用微生物分离纯化技术,在培养基中加入不同浓度的Cr3+、Cr6+,经过长时间驯化,从污染土壤中筛选出2株对Cr具有较高抗性的菌株(A和B),对其进行了形态、生理生化特性及分子生物学鉴定,并研究了其最佳生长条件及对Cr3+的生物吸附规律。结果表明,菌株A和B分别为蜡状芽孢杆菌(Bacillus cereus)和米根霉菌(Rhizopus oryzae)。菌株A和B的最适生长pH值均为7,最适生长温度均为30℃,最佳装液量为80~100 mL(250 mL摇瓶)。在培养时间一定时,随着Cr3+浓度的增加,菌株对Cr3+的吸附率减少,而生物吸附量则逐渐增大;在Cr3+浓度一定时,随着培养时间的延长,菌体对Cr3+的吸附率呈现出先增加后减少的趋势,这与生物吸附量的变化趋势基本一致。在Cr3+浓度为100 mg/L时,菌株A和B对Cr3+的吸附率达到最大,分别为51.47%和46.36%。     

基于改性凹凸棒土的强化混凝处理高藻低浊原水工艺

针对水厂低浊高藻水的处理难题,研究了改性凹凸棒土(改性凹土)联合聚合氯化铝(PAC)强化混凝的除藻除浊效果。设计实验原水条件为叶绿素a(chl-a)浓度为98.58~110.35μg/L,浊度(5.6±0.5)NTU。考察了PAC和改性凹土的复配投加量、混凝沉淀时间、pH、投加顺序、搅拌速率等工艺参数对Chl-a和浊度耦合去除效果的影响。结果表明,"PAC+改性凹土"对Chl-a和浊度的去除效果明显优于单投PAC的效果。当PAC投药量12 mg/L,改性凹土投药量10 mg/L,沉淀时间20 min时,对Chl-a和浊度的去除率可分别达到92.5%和89.2%,可至少减少40%的PAC投量,且形成的矾花密实,沉降速度快,去除效率高。最适pH范围为7~8。投加顺序应为先投加改性凹土,混合搅拌转数宜慢速,可控制为50 r/min。     

应用加载磁混凝处理微污染河水

实验对比考察了常规混凝和加载磁混凝工艺对微污染河水中COD、浊度和TP等污染物的去除效果,系统研究了混凝剂用量、磁种加载量、搅拌条件和药剂投加顺序等因素对加载磁混凝效果的影响。实验结果表明,加载磁种后沉淀颗粒的体积平均粒径为从常规混凝工艺的50.1 μm显著增加到68.6 μm;污染物去除效果明显优于常规混凝工艺,尤其对浊度和总磷的去除效果得到了显著的提升;在实验最优条件下COD、浊度和TP的去除率分别达到54.17%、99.28%和75.82%;并且加载磁种后可减少50%以上的混凝剂投加量,同时大大缩短沉淀时间。     

Oil Identification Based on a Goodness-of-Fit Metric Applied to Hydrocarbon Analysis Results

Assessment of environmental damage following accidental oil spills requires reliable oil identification methods. Results from hydrocarbon analyses of environmental samples are often difficult to interpret, because of the changes in oil composition (or weathering) that follows release into the environment, and because of confounding by hydrocarbons from other sources. To a first-order approximation, weathering proceeds according to simple first-order loss-rate (FOLR) kinetics for polycyclic aromatic hydrocarbons (PAH) based on molecular size. This relationship between relative weathering rate and molecular size can be exploited to infer the initial PAH composition of spilled oils, and this information can be combined with results for weathering-invariant analytes to substantially increase the precision and accuracy of hydrocarbon source recognition methods. The approach presented here evaluates a goodness-of-fit metric between the measured hydrocarbon composition of an environmental sample and a suspected source, after correcting for PAR weathering losses based on FOLR kinetics. Variability from analytical and sampling error may thus be accounted for, and source identifications can be expressed as objective probability statements. This approach is illustrated by application to four independent case studies.     

Biodegradation of α and β Endosulfan in Soil as Influenced by Application of Different Organic Materials

Abstract

A laboratory pot experiment was conducted to study the effect of amending soil with four different sources of organic matter on the degradation rate of α and β endosulfan isomers. Poultry by-product meal, poultry manure, dairy manure, and municipal solid waste compost were cured, dried, ground (<1 mm) and thoroughly mixed with a calcareous soil at a rate of 2% and placed in plastic pots. Endosulfan was added at the rate of 20 mg kg^?1. The moisture level was kept near field capacity and the pots were kept at room temperature. Soil sub-samples, 100 g each, were collected from every pot at days 1, 8, 15, 22, 29, 43, and 57 for the measurement of endosulfan isomers. Endosulfan residues were extracted from the soil samples with acetone. The supernatant was filtered through anhydrous sodium sulphate, 5 mL aliquot was diluted to 25 mL with hexane, mixed well, and then two sub-samples from the filtrates were analyzed for α and β endosulfan isomers by gas chromatography. The results indicated that the half-life (T _½) of α-endosulfan in the poultry by-product meal treatment was 15 days compared to about 22 days in the other treatments. The T _½ of β-endosulfan was 22 days in the poultry by-product meal treatment and followed a bi-phasic pattern, 57 days in the municipal solid waste compost treatment and the extrapolated T _½ was about 115 days for the other three treatments.