Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

ABR-生物接触氧化法处理果汁废水实验分析

厌氧式折流反应器(Anaerobic Baffled Reactor,简称ABR)是一种新型高效厌氧反应器,具有工艺技术简单、建设投资费用低、运行管理方便、固液分离效果好、出水水质好、运行稳定可靠、对有毒物质适应性强等优点,是一种极具开发应用前景的废水生物处理新技术。ABR最大的特点是在反应器中设置上下折流板而在水流方向上形成依次串联的隔室,从而使其中的微生物种群沿长度方向的不同隔室实现产酸和产甲烷相的分离。该反应器具有结构简单,截留污泥能力强,系统处理效果稳定,运行管理方便等优点。分析了ABR及ABR与其它工艺的联合在果汁废水处理方面的应用。     

Mitigation of eutrophication caused by wastewater discharge: A simulation-based approach

Mitigation of eutrophication, intensified by excessive nutrient load discharge in wastewaters regulated by restrictive legal requirements, remains one of today’s most important global problems. Despite implementation of the Water Framework Directive, the Urban Wastewater Directive and the HELCOM recommendations, the actual condition of surface water is still not satisfactory. In response to the above, the study presents an alternative approach for surface water protection against eutrophication based on the selection of appropriate nutrient removal technologies. An activated sludge model simulation was used to enable the identification of environmentally justified nutrient removal systems with lowest eutrophication potential of treated wastewater conditioned by bioavailable nutrient forms content. Based on the outcome of the study, the 3-stage Bardenpho system was identified as the most efficient for bioavailable phosphorus removal, while the Johannesburg system proved to have the highest efficiency for bioavailable nitrogen removal. The proposed eutrophication mitigation approach underlines the need for a reconsideration of current legal regulations which ignore nutrient bioavailability and key eutrophication limiting factors.     

坡岸截留强化处理设施在不同运行条件下对农业面源污染物去除效果

对坡岸截留强化处理设施在不同温度、不同雨强、不同降雨间隔条件下处理农业面源污染进行中试试验研究.结果表明,水温从20℃下降至4.3℃,COD、TN、NH+4-N、TP去除率下降了15.58%、48.93%、42.26%、57.75%;降雨强度由0.65mm·min-1增加1倍至1.30 mm·min-1,COD的平均去除率低了15.19%,TN、NH+4-N的去除效率相当,TP的去除效率提高了11.21%,但COD、TN、NH+4-N、TP单位面积去除的总量却提高了26.27%、68.3%、32.6%、104.2%;降雨间隔从2 d增加到4 d时对COD去除的影响不大,但使NH+4-N、TN的处理效率提高19.31%、13.95%,对TP的单位面积去除量提高71.43%,但去除总量有限.     

微气泡臭氧催化氧化-生化耦合工艺深度处理煤化工废水

采用微气泡臭氧催化氧化-生化耦合工艺对煤化工废水生化出水进行深度处理,考察耦合系统处理性能及不同臭氧投加量和进水COD量比值的影响.结果表明,微气泡臭氧催化氧化处理能够有效降解废水中难降解含氮芳香族污染物,去除部分COD并释放氨氮,显著提高废水可生化性,臭氧利用率接近100%,无需进行臭氧尾气处理;同时为生化处理提供充足溶解氧(DO),实现生化处理对COD和氨氮的进一步有效去除,生化处理无需曝气.在系统出水回流比为30%、臭氧投加量和进水COD量之比为0.44 mg·mg~(-1)的运行条件下,耦合系统处理性能较好.微气泡臭氧催化氧化处理对COD去除率为42.5%,臭氧消耗量与COD去除量比值为1.38 mg·mg~(-1),臭氧利用率为98.0%;生化处理对COD去除率为42.3%;耦合系统整体COD去除率为66.7%,最终平均出水COD浓度为91.5 mg·L~(-1),估算整体臭氧消耗量与COD去除量比值为0.68 mg·mg~(-1),具有较优的技术经济性能.     

Control of aliphatic halogenated DBP precursors with multiple drinking water treatment processes: Formation potential and integrated toxicity

The comprehensive control efficiency for the formation potentials(FPs) of a range of regulated and unregulated halogenated disinfection by-products(DBPs)(including carbonaceous DBPs(C-DBPs), nitrogenous DBPs(N-DBPs), and iodinated DBPs(I-DBPs)) with the multiple drinking water treatment processes, including pre-ozonation, conventional treatment(coagulation–sedimentation, pre-sand filtration), ozone-biological activated carbon(O_3-BAC) advanced treatment, and post-sand filtration, was investigated. The potential toxic risks of DBPs by combing their FPs and toxicity values were also evaluated.The results showed that the multiple drinking water treatment processes had superior performance in removing organic/inorganic precursors and reducing the formation of a range of halogenated DBPs. Therein, ozonation significantly removed bromide and iodide,and thus reduced the formation of brominated and iodinated DBPs. The removal of organic carbon and nitrogen precursors by the conventional treatment processes was substantially improved by O_3-BAC advanced treatment, and thus prevented the formation of chlorinated C-DBPs and N-DBPs. However, BAC filtration leads to the increased formation of brominated C-DBPs and N-DBPs due to the increase of bromide/DOC and bromide/DON.After the whole multiple treatment processes, the rank order for integrated toxic risk values caused by these halogenated DBPs was haloacetonitriles(HANs)》haloacetamides(HAMs) haloacetic acids(HAAs) trihalomethanes(THMs) halonitromethanes(HNMs) 》I-DBPs(I-HAMs and I-THMs). I-DBPs failed to cause high integrated toxic risk because of their very low FPs. The significant higher integrated toxic risk value caused by HANs than other halogenated DBPs cannot be ignored.     

我国工业危险废物的来源、处理及监管对策与建议

通过大量环境统计数据的分析,对我国工业危险废物的产生、综合利用、处置和贮存,从行业来源、区域分布进行了分析和总结。结合我国工业危险废物企业自建设施和政府集中处理设施处理情况,对我国工业危险废物的处理和环保监管对策提出了若干建议。     

滇西北高原湖泊剑湖演变过程及其生态环境效应分析

以滇西北高原湖泊剑湖为研究区,1974—2015年间8期遥感影像为数据源,运用遥感和地理信息系统技术,研究剑湖湖泊近40年间的时空演变过程,探析剑湖湖泊的入湖污染物及其生态环境效应变化。结果表明:近40年来剑湖湖泊面积呈现先明显减少再增加后缓慢减少的变化规律,由1974年的504.47 hm~2减至2015年的451.72 hm~2;目前剑湖水体中COD含量较低,符合地表水环境质量Ⅱ类标准;TP含量满足Ⅲ类标准;TN含量仅可满足IV类标准;剑湖入湖的主要污染源是农村生活污染和农业面源污染;随着时间的演变剑湖湖泊TN、TP污染物浓度呈上升趋势,剑湖湖泊生态系统受到极大干扰。     

煤制烯烃废水处理与回用技术解析

针对煤制烯烃项目废水的来源及水质特点,从生化处理技术与回用处理技术方面阐述了煤制烯烃废水处理现状及存在问题,展望了煤制烯烃废水处理与回用技术未来发展方向,指出了新型脱氮工艺、膜集成工艺及分质结晶技术在煤制烯烃废水处理中的可行性,为煤化工废水处理与资源化利用提供理论参考。     

广西壮族自治区污水处理厂运行状况及特征分析

基于广西壮族自治区126座污水处理厂2015年运行状况的调查数据,分析广西污水处理厂的工艺特点、污泥处置、出水水质达标情况、运行负荷率和运行费用,评估污水处理厂运行的效率和效果,分析存在的问题,并就污水处理厂的运行和管理提出建议。