抚顺市酸雨污染特征及变化趋势

在抚顺市酸雨监测数据分析的基础上,对抚顺地区的酸雨污染特征及其变化趋势和污染来源进行了探讨。     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

离子色谱法测定废气中硫酸雾实验研究

文章建立了离子色谱法测定废气中硫酸雾的分析方法,制备好的样品经0．45um微孔滤膜抽滤,采用AS14A阴离子交换色谱柱分离,电导检测器检测,以0．8mmol／L碳酸钠和0．1mmol／L碳酸氢钠混合溶液为流动相,流速为0．5ml／min进行测定,以保留时间定性,峰面积进行定量,方法的适用范围为0．50～50mg／m3。与铬酸钡分光光度法进行比对试验,无显著性差异。该方法操作简便、灵敏度高、准确度好,实用性强,适用于大批量环境样品的分析。     

局地化工区污染案例的小气候特征分析研究

针对群众举报夜晚受不明气体污染中毒的两起事件,经过环保部门的现场勘查及监测,确定造成纺织厂污染的大气污染物为HCl气体,来自于纺织厂隔壁的农药厂装盐酸的空罐、罐区受污染的固体废弃物及受污染的土壤;助剂厂附近村民所受的污染物为HNO3、NO2和NOx气体,来自于助剂厂装硝酸的空罐、跑冒滴漏的废水废气、固体废弃物及受污染的土壤。夜晚气温降到露点,空气湿度达到饱和状态,气体污染物与空气中的水分结合形成对人体危害更重的酸或酸性气体;这两个工厂又都位于鸭绿江边的化工区内,具有局地小气候特征,夜晚易形成类似于海陆风的微风,形成局地污染。     

土地利用变化对土壤硝化及氨氧化细菌区系的影响

以西藏高原相邻的原始森林、天然草原和农田土壤为研究对象,分别采用室内培养法和nested PCR-DGGE技术,对比研究了这3个生态系统的土壤硝化势、硝态氮浓度以及土壤氨氧化细菌（AOB）菌群区系.结果表明,农田土壤的硝化势和硝态氮（NO 3--N）浓度显著高于相邻的草原和森林土壤,硝化势分别是森林和草原土壤的9倍和11倍,NO 3--N是农田土壤无机氮（Nmin）的主要成分,占无机氮的70%～90%.铵态氮（NH 4＋-N）则是森林和草原土壤中主要的无机氮形态.原始森林和天然草原间的硝化势和硝态氮浓度没有显著差异.原始森林的土壤AOB菌群数量、多样性及均匀度最低.天然草原生态系统转换为农田后,土壤AOB菌群的多样性和均匀度显著降低,但是农田土壤的AOB菌群结构仍与其前身草原生态系统有较高的相似性.原始森林的AOB菌群数量、多样性及均匀度最低直接导致了其硝化势最低;农田土壤的硝化势和硝态氮浓度最高意味着农田生态系统中优势AOB的活性最高.以上结果表明,土地利用变化导致土壤氮素内循环及其关键微生物AOB的多样性与活性均发生显著变化,这些变化会影响土壤环境质量以及生态系统的持续与稳定.