Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

ABR-生物接触氧化法处理果汁废水实验分析

厌氧式折流反应器(Anaerobic Baffled Reactor,简称ABR)是一种新型高效厌氧反应器,具有工艺技术简单、建设投资费用低、运行管理方便、固液分离效果好、出水水质好、运行稳定可靠、对有毒物质适应性强等优点,是一种极具开发应用前景的废水生物处理新技术。ABR最大的特点是在反应器中设置上下折流板而在水流方向上形成依次串联的隔室,从而使其中的微生物种群沿长度方向的不同隔室实现产酸和产甲烷相的分离。该反应器具有结构简单,截留污泥能力强,系统处理效果稳定,运行管理方便等优点。分析了ABR及ABR与其它工艺的联合在果汁废水处理方面的应用。     

蠡河底泥中反硝化复合菌群富集及菌群结构研究

从无锡市滨湖区蠡河底泥中富集培养反硝化复合菌群,研究其在不同富集培养阶段TN、NO-3-N、NO-2-N、NH+4-N和COD动态变化,分析反硝化过程中气体释放总量、释放速率和成分,通过构建全长16S r DNA克隆文库研究其菌落结构.结果表明,反硝化复合菌群富集在阶段4时脱氮效果最佳,仅在9 h内,330 mg·L-1的TN负荷下,TN去除率达90.9%,NO-3-N去除率达100%,中间产物NO-2-N和NH+4-N积累量最少,分别为3.39 mg·L-1和16.64 mg·L-1,COD去除率达85%;释放气体260m L,气体主要成分为N2,同时还有少量的CH4和CO2等.富集培养反硝化复合菌群细菌属于Pseudomonadaceae科和Rhodocyclaceae科,为Proteobacteria门,OUT丰度分别为57.8%和31.6%,Pseudomonadaceae科是优势类群.     

Mitigation of eutrophication caused by wastewater discharge: A simulation-based approach

Mitigation of eutrophication, intensified by excessive nutrient load discharge in wastewaters regulated by restrictive legal requirements, remains one of today’s most important global problems. Despite implementation of the Water Framework Directive, the Urban Wastewater Directive and the HELCOM recommendations, the actual condition of surface water is still not satisfactory. In response to the above, the study presents an alternative approach for surface water protection against eutrophication based on the selection of appropriate nutrient removal technologies. An activated sludge model simulation was used to enable the identification of environmentally justified nutrient removal systems with lowest eutrophication potential of treated wastewater conditioned by bioavailable nutrient forms content. Based on the outcome of the study, the 3-stage Bardenpho system was identified as the most efficient for bioavailable phosphorus removal, while the Johannesburg system proved to have the highest efficiency for bioavailable nitrogen removal. The proposed eutrophication mitigation approach underlines the need for a reconsideration of current legal regulations which ignore nutrient bioavailability and key eutrophication limiting factors.     

华北地区乡村站点(曲周)夏季PM2.5中二次无机组分的生成机制与来源解析

利用大气PM2.5水溶性组分及其气态前体物在线测量系统(GAC-IC)于2014年6月9日~7月11日对华北地区乡村站点曲周大气PM2.5中水溶性组分及其气态前体物进行了在线测量,分析了PM2.5中水溶性组分与气态前体物日变化规律及其相互作用,探讨了当地细颗粒物的气粒转化机制并分析了其来源.结果表明夏季曲周大气PM2.5中水溶性无机离子与相关气态前体物的浓度呈现明显的日变化规律.观测期间,PM2.5中SO2-4、NH+4和NO-3的平均浓度分别是26.28、18.08和16.36μg·m-3,是PM2.5中最主要的水溶性无机离子,约占PM2.5质量浓度的76.23%;气态前体物中,NH3浓度明显偏高、平均值为44.85μg·m-3,主要来源于当地的农业活动排放;硫氧化率(SOR)和氮氧化率(NOR)平均值分别是0.60和0.30,表现出明显的二次污染特征.经相关性分析发现:曲周大气PM2.5中NH+4与NO-3、SO2-4有良好的相关性,且表现为富氨状态,NH+4以(NH4)2SO4形式存在,NO-3的生成主要受HNO3的限制.对NH4NO3平衡进行研究发现:与夜间相反,白天曲周大气环境不利于NH4NO3生成和保持.结果也表明,二次转化是曲周夏季细颗粒物的主要来源,堆肥与农田释放的NH3是导致高浓度二次无机颗粒物(SNA)的重要因素.     

微气泡臭氧催化氧化-生化耦合工艺深度处理煤化工废水

采用微气泡臭氧催化氧化-生化耦合工艺对煤化工废水生化出水进行深度处理,考察耦合系统处理性能及不同臭氧投加量和进水COD量比值的影响.结果表明,微气泡臭氧催化氧化处理能够有效降解废水中难降解含氮芳香族污染物,去除部分COD并释放氨氮,显著提高废水可生化性,臭氧利用率接近100%,无需进行臭氧尾气处理;同时为生化处理提供充足溶解氧(DO),实现生化处理对COD和氨氮的进一步有效去除,生化处理无需曝气.在系统出水回流比为30%、臭氧投加量和进水COD量之比为0.44 mg·mg~(-1)的运行条件下,耦合系统处理性能较好.微气泡臭氧催化氧化处理对COD去除率为42.5%,臭氧消耗量与COD去除量比值为1.38 mg·mg~(-1),臭氧利用率为98.0%;生化处理对COD去除率为42.3%;耦合系统整体COD去除率为66.7%,最终平均出水COD浓度为91.5 mg·L~(-1),估算整体臭氧消耗量与COD去除量比值为0.68 mg·mg~(-1),具有较优的技术经济性能.     

Control of aliphatic halogenated DBP precursors with multiple drinking water treatment processes: Formation potential and integrated toxicity

The comprehensive control efficiency for the formation potentials(FPs) of a range of regulated and unregulated halogenated disinfection by-products(DBPs)(including carbonaceous DBPs(C-DBPs), nitrogenous DBPs(N-DBPs), and iodinated DBPs(I-DBPs)) with the multiple drinking water treatment processes, including pre-ozonation, conventional treatment(coagulation–sedimentation, pre-sand filtration), ozone-biological activated carbon(O_3-BAC) advanced treatment, and post-sand filtration, was investigated. The potential toxic risks of DBPs by combing their FPs and toxicity values were also evaluated.The results showed that the multiple drinking water treatment processes had superior performance in removing organic/inorganic precursors and reducing the formation of a range of halogenated DBPs. Therein, ozonation significantly removed bromide and iodide,and thus reduced the formation of brominated and iodinated DBPs. The removal of organic carbon and nitrogen precursors by the conventional treatment processes was substantially improved by O_3-BAC advanced treatment, and thus prevented the formation of chlorinated C-DBPs and N-DBPs. However, BAC filtration leads to the increased formation of brominated C-DBPs and N-DBPs due to the increase of bromide/DOC and bromide/DON.After the whole multiple treatment processes, the rank order for integrated toxic risk values caused by these halogenated DBPs was haloacetonitriles(HANs)》haloacetamides(HAMs) haloacetic acids(HAAs) trihalomethanes(THMs) halonitromethanes(HNMs) 》I-DBPs(I-HAMs and I-THMs). I-DBPs failed to cause high integrated toxic risk because of their very low FPs. The significant higher integrated toxic risk value caused by HANs than other halogenated DBPs cannot be ignored.     

Effect of lubricant sulfur on the morphology and elemental composition of diesel exhaust particles

This work investigates the effects of lubricant sulfur contents on the morphology, nanostructure, size distribution and elemental composition of diesel exhaust particle on a light-duty diesel engine. Three kinds of lubricant (LS-oil, MS-oil and HS-oil, all of which have different sulfur contents: 0.182%, 0.583% and 1.06%, respectively) were used in this study. The morphologies and nanostructures of exhaust particles were analyzed using high-resolution transmission electron microscopy (TEM). Size distributions of primary particles were determined through advanced image-processing software. Elemental compositions of exhaust particles were obtained through X-ray energy dispersive spectroscopy (EDS). Results show that as lubricant sulfur contents increase, the macroscopic structure of diesel exhaust particles turn from chain-like to a more complex agglomerate. The inner cores of the core-shell structure belonging to these primary particles change little; the shell thickness decreases, and the spacing of carbon layer gradually descends, and amorphous materials that attached onto outer carbon layer of primary particles increase. Size distributions of primary particles present a unimodal and normal distribution, and higher sulfur contents lead to larger size primary particles. The sulfur content in lubricants directly affects the chemical composition in the particles. The content of C (carbon) decreases as sulfur increases in the lubricants, while the contents of O (oxygen), S (sulfur) and trace elements (including S, Si (silicon), Fe (ferrum), P (phosphorus), Ca (calcium), Zn (zinc), Mg (magnesium), Cl (chlorine) and Ni (nickel)) all increase in particles.     

港口罢工对周边空气质量的影响

港口污染物的排放浓度极大地影响着周边的空气质量,以2013年3月28日香港国际集装箱码头发生的罢工事件为契机来探究港口运作短暂的瘫痪对周边空气质量的影响。首先,进行污染物之间的相关性分析确定影响本次罢工事件的污染物主要为NO_2、NO_x、SO_2以及O_3。其次,基于罢工前、罢工期间以及罢工后污染物排放的浓度变化,进行横向对比发现罢工期间的污染物确实有一定程度的减少。再次,利用纵向对比排除四季带来的影响探究不同年份同一阶段污染物浓度的变化情况评估罢工期间的空气质量。最后,以NO_2为例建立预测模型对罢工期间的NO_2浓度进行预测,根据实际值与预测值之间的差异来说明罢工影响了NO_2的预测趋势。这项研究主要强调港口空气质量对整个环境的影响,在一定程度上说明政府实施政策的有效性,为政府提供了决策支持,同时也要注重污染物之间的相互转化作用对环境的影响。     

我国工业危险废物的来源、处理及监管对策与建议

通过大量环境统计数据的分析,对我国工业危险废物的产生、综合利用、处置和贮存,从行业来源、区域分布进行了分析和总结。结合我国工业危险废物企业自建设施和政府集中处理设施处理情况,对我国工业危险废物的处理和环保监管对策提出了若干建议。