臭氧联用技术深度处理腈纶废水的效果对比

将臭氧分别与超声波、H2O2、紫外光等联用,深度处理干法腈纶生产厂生化池出水,对各种联用技术的处理效果进行了研究。实验结果表明：在进水流量2 L/min、反应时间30 min、臭氧加入量3.5 g/（L?h）的条件下,当超声功率为300 W时,臭氧-超声联用技术的COD去除率为30.0%;当H2O2加入量为0.4 mL/L时,臭氧-H2O2联用技术的COD去除率为50.7%;当紫外灯功率为40 W时,臭氧-紫外光联用技术的COD去除率为49.9%;在各种联用技术中,臭氧-H2O2联用技术的运行成本最低（为7.5 元/t）,且处理后出水COD为143 mg/L,达到《<污水综合排放标准>（GB8978—1996）中石化工业COD标准值修改单》中的一级排放标准。综合考虑,臭氧-H2O2联用技术是深度处理干法腈纶废水的最优工艺。     

烟气脱硫溶液中硫酸根的去除

分别采用石灰乳化学沉淀法和低温结晶法去除烟气脱硫溶液中的SO42-。实验结果表明：在室温、CaO溶液质量分数25%的条件下,石灰乳化学沉淀法对SO42-的去除率仅为59.51%,且向溶液中引入了Ca2+,产生的硫酸钙固体废物难以再生利用;采用低温结晶法处理烟气脱硫溶液,在结晶温度7 ℃、结晶时间3 h、NaOH加入量34.8 g/L的条件下,SO42-的去除率为82.04%、滤液中的ρ（Na+）为3.88 g/L。在现场工业应用试验中,采用低温结晶法去除烟气脱硫溶液中的SO42-,平均SO42-的去除率可达70.00%以上,滤液中的ρ（Na+）小于15.00 g/L。该法可有效抑制烟气脱硫溶液中SO42-含量的增加。     

Mn/γ-Al2O3催化剂的制备及头孢合成废水的催化臭氧氧化法深度处理

对Mn/γ-Al₂O₃催化剂的制备条件及头孢合成废水的催化臭氧氧化法深度处理工艺条件进行了优化。实验结果表明：以Mn（NO₃）₂溶液为浸渍液,Mn/γ-Al₂O₃催化剂的最优制备条件为浸渍液浓度0.10 mol/L、浸渍时间9 h、焙烧温度400 ℃、焙烧时间2 h;在反应时间为30 min、废水pH为9.0、臭氧通量为4.6 mg/min、催化剂加入量为5 g/L的条件下,当进水COD、BOD₅、ρ（氨氮）和色度分别为220~250 mg/L,8~10 mg/L,10~12 mg/L和60~70倍时,出水COD、BOD₅、ρ（氨氮）和色度的平均去除率分别为53%,30%,33%和93%,出水水质满足GB 21904—2008《化学合成类制药工业水污染物排放标准》的要求。     

臭氧氧化—包埋菌流化床生物处理组合工艺深度处理煤气化废水

采用臭氧氧化—包埋菌流化床生物处理组合工艺对煤气化废水进行深度处理。实验结果表明：当臭氧的质量浓度20 mg/L、臭氧进气流量1.5 L/min、臭氧通气时间30 min、包埋菌流化床水力停留时间24 h时,臭氧氧化工序的COD去除率达到30.0%~40.0%,总酚去除率达到100.0%;包埋菌流化床工序的COD去除率达到60.0%以上,氨氮的去除率大于95.0%;经组合工艺处理后,出水COD<60 mg/L,ρ（氨氮）<1.0 mg/L,ρ（总酚）未检出,色度小于50倍,达到GB8978—1996《污水综合排放标准》中的一级排放标准。     

微波活化过硫酸钾深度处理印染废水

为了深度处理印染废水生化出水,使其达到工业回用要求,利用微波活化过硫酸钾产生具有强氧化性的硫酸根自由基·SO-4,降解印染废水生化出水中的有机污染物。考察了硫酸亚铁的投加量,过硫酸钾的浓度及pH的影响,并通过对比实验讨论了微波活化作用效果。结果表明,过硫酸钾微波组合能够有效地去除生化出水中的TOC和色度。对于某印染废水生化出水,处理效果在pH=10时最好,当过硫酸钾浓度为14 g/L时,TOC去除率达57.60%,脱色率为98.28%。研究结果表明,过硫酸钾微波组合对于印染废水的深度处理效果良好,有较好的应用前景。     

Fuel efficiency improvement of a dual-fuel engine fuelled with Honge oil methyl ester (HOME)–bioethanol and producer gas

Renewable and alternative fuels have numerous advantages compared with fossil fuels as they are renewable and biodegradable and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues (Yaliwal et al. 2013. International Journal of Sustainable Engineering, doi:10.1080/19397038.2013.801530. Zhu et al. 2011a, Applied Thermal Engineering 31 (14–15): 2271–2278; Zhu et al. 2011b, Fuel 90: 1743-1750; Banapurmath, Tewari, and Hosmath 2008, Renewable Energy 33: 2007-2018; Banapurmath 2009, “Performance, Combustion and Emission Characteristics of a Single Cylinder Direct Injection CI Engine Operated on Dual Fuel Mode Using Honge Oil and Producer Gas.” PhD thesis, 1–195; Banapurmath et al. 2011, Waste and Biomass Valorization 2: 1–11). In this context, the main objective of the present work is to study methods of biofuel production such as Honge oil methyl ester (HOME) using a conventional transesterification process and bioethanol from the Calliandra calothyrsus shrub using a new pretreatment method known as hydrothermal explosion. Further, experimental investigations were carried out on a single-cylinder, four-stroke, direct-injection stationary diesel engine operating in a dual-fuel mode using HOME, bioethanol and producer gas combinations to determine its performance, combustion and emission characteristics. The performance of the dual-fuel engine was analyzed at optimized engine conditions. HOME-Bioethanol (BE) blends such as HOME+ 5% bioethanol (BE5), HOME+ 10% bioethanol (BE10) and HOME+ 15% bioethanol (BE15) were prepared by adding bioethanol to HOME (on volume basis) in different proportions ranging from 5 to 15% with an increment of 5%. In this present work, the effect of different BE blends on the performance of producer gas fuelled dual fuel engine was studied. Experimental investigation on dual fuel engine using BE5-Producer gas operation resulted in up to 4–9% increased brake thermal efficiency with decreased hydrocarbon (HC), carbon monoxide (CO) and marginally increased nitric oxide (NOx) emission levels compared to HOME-Producer gas, BE10-producer gas and BE15-producer gas mode of operation. However, it was observed that, the overall performance of BE-producer gas operation was found to be lower compared to diesel-producer gas operation.     

Performance,combustion and emission characteristics of a single-cylinder,four-stroke,direct injection diesel engine operated on a dual-fuel mode using Honge oil methyl ester and producer gas derived from biomass feedstock of different origin

Renewable and alternative fuels have numerous advantages compared with fossil fuels, as they are renewable and biodegradable, and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues. In this context, present work was carried out to investigate the feasibility of alternative and renewable fuels derived from biomass feedstock of different origin for engine applications. The present study was also extended to study the effect of producer gas composition derived from different biomass feedstock on the performance, combustion and emission characteristics of a single-cylinder, four-stroke, direct injection stationary diesel engine operated on a dual-fuel mode using Honge oil methyl ester (HOME) and producer gas induction. The performance of the engine was evaluated with a constant injection timing of 27° before top dead centre, an injection pressure of 205 bar for the diesel–producer gas combination and 230 bar for the HOME–producer gas combination and a compression ratio of 17.5. The results showed that the performance of the dual-fuel engine varies with the composition of the producer gas and depends on the type of biomass feedstock used in the gasifier. Experimental investigations on the dual-fuel engine showed that brake thermal efficiency values for the engine operated using HOME–producer gas derived from babul, neem and honge woods were found to be 17.2, 14.3 and 11.56% respectively, compared to 23.8% for diesel–producer gas operation at 80% load. However, the results showed better engine performance with lower exhaust emission levels for the operation of HOME–producer gas derived from the ordinary or babul wood compared with the operation of that derived from the neem and Honge woods. In view of this, present study reveals that use of alternative and renewable fuels for dual fuel engine can be considered as an immediate solution for the development of rural areas and emergency use in the event of severe diesel fuel shortage.     

炼油恶臭污染治理技术在中国石化天津分公司的应用实例

简述了炼油装置区恶臭污染源的主要分布、恶臭气体组成和排放规律,介绍了恶臭治理的基本方法。通过治理实例,重点分析了目前常用的吸收法、燃烧法、生物法和吸附法等恶臭治理技术的优势和相对不足,并对恶臭治理应用技术方案的选择提出建议。     

共代谢膜生物反应器法处理二甲基亚砜废水

采用蔗糖作为共代谢基质与一体式好氧膜生物反应器（MBR）工艺相结合处理二甲基亚砜（DMSO）废水。考察了装置的污泥驯化效果、DMSO去除率、污泥的性能、HRT和冲击负荷对DMSO去除率的影响。试验结果表明：驯化第29天,DMSO去除率达98.5%,表明MBR内的污泥已驯化成功;在MBR运行的正式期,当DMSO处于高负荷状态时,DMSO去除率较低;随蔗糖加入量的增加,DMSO去除率逐渐提高,最终恢复到DMSO高负荷冲击前的DMSO去除效果;正常运行时,装置进水ρ（DMSO）=257~1 448 mg/L（平均值为718 mg/L）、出水ρ（DMSO）=6~22 mg/L（平均值为7 mg/L）,DMSO去除率为96.4%~99.6%（平均值为98.9%）;在MBR运行的正式期,污泥体积指数小于100 mL/g,表明污泥的沉降性能较好,MLVSS/MLSS较高,表明污泥的活性高,MBR内MLSS的平均值为5.52 g/L,MLVSS的平均值为4.78 g/L;MBR适宜的HRT为12 h。     

生物滴滤塔处理氯苯废气的工艺性能

将活性污泥培养及驯化后接种于生物滴滤塔中,挂膜启动后处理模拟氯苯废气（简称氯苯废气）,考察了生物滴滤塔在挂膜启动阶段及稳定运行阶段的性能。实验结果表明：接种41 d后生物滴滤塔成功挂膜,此时氯苯去除率稳定在90%以上;生物滴滤塔稳定运行阶段,随着进气中氯苯质量浓度由303.82 mg/m³逐渐增至1 489.05 mg/m³,氯苯去除率从85.1%降至70.1%。处理氯苯废气适宜的工艺条件为：空塔停留时间超过45 s,喷淋液流量31.8 mL/min,氯苯负荷23.97~128.01 g/（m³·h）。生物滴滤塔对喷淋液的酸性环境有较好的适应性,喷淋液pH的变化对氯苯去除率无显著影响。