基于pH调控的城市污泥厌氧发酵产酸小试研究

本研究设计了热碱预处理-半连续流厌氧发酵污泥处理工艺,探究了p H对热碱预处理污泥产酸性能的影响,同时对发酵液作为碳源回用于污水厂强化脱氮除磷进行了质量衡算.在30 L厌氧发酵罐中考察了偏中性(p H=6.5)和碱性(p H=10.0)条件下热碱预处理污泥发酵的挥发性脂肪酸(VFA)产生及分布、蛋白质及碳水化合物的消耗和氮磷释放情况.结果表明,污泥热碱预处理-半连续流厌氧发酵工艺的VFA产量稳定,在p H为6.5和10.0的条件下,发酵罐中平均VFA产率分别为333.29 mg·g-1(以每g VS产生的COD(mg)计,下同)和250.64 mg·g-1,p H为6.5时产酸更稳定,且产量较高,但碱性条件更适合产乙酸.两种p H条件下的SCOD、溶解性蛋白质、溶解性多糖、氮和磷的释放都无较大差异.质量衡算结果表明,以处理量为50000 m3·d-1的城市污水处理厂为例,其产生的污泥经过热碱预处理-半连续流厌氧发酵产酸工艺,产生的VFA能够满足该污水处理厂脱氮除磷提标改造的碳源需求.     

Effects of Ca(OH)2 assisted aluminum sulfate coagulation on the removal of humic acid and the formation potentials of tri-halomethanes and haloacetic acids in chlorination

The effects of addition of calcium hydroxide on aluminum sulphate(or alum) coagulation for removal of natural organic matter(NOM) and its subsequent effect on the formation potentials of two major types of regulated disinfection byproducts(DBPs),haloacetic acids(HAAs) and trihalomethanes(THMs),have been examined.The results revealed several noteworthy phenomena.At the optimal coagulation pH(i.e.6),the coagulation behavior of NOM water solutions versus alum dose,showed large variation and a consequent great change in the formation potentials of the DBPs at certain coagulant doses.However,with addition of a relatively small amount of Ca(OH) 2,although the zeta potential of coagulated flocs remained almost the same,NOM removal became more consistent with alum dose.Importantly,also the detrimental effect of charge reversal on NOM removal at the low coagulant dose disappeared.This resulted in a steady decrease in the formation potentials of DBPs as a function of the coagulant dose.Moreover,the addition of Ca(OH) 2 broadened the pH range of alum coagulation and promoted further reduction of the formation potentials of the DBPs.The enhancement effects of Ca(OH) 2 assisted alum coagulation are especially pronounced at pH 7 and 8.Finally,synchronous fluorescence spectra showed that the reduction in DBPs formation potential by Ca(OH) 2-assisted alum coagulation was connected to an enhanced removal of small hydrophobic and hydrophilic HA molecules.Ca(OH) 2-assistance of alum coagulation appeared to increase substantially the removal of the hydrophilic HA fraction responsible for HAAs formation,prompting further reduction of HAA formation potentials.     

Natural organic compounds as alternative to methyl bromide for nematodes control

Thirty-three organic acids and furfural metabolites were examined for their nematicidal activity against plant-parasitic, free-living and predacious nematodes. Propionic acid, 2-methylhexanoic acid, lactic acid, maleic acid, and furic acid were the most effective nematicides among normal chain organic acids, branched organic acids, hydroxy/keto-acids, dicarboxylic acids and furfural metabolites, respectively. Seven of the tested compounds were found to have more than 90% mortality thus designating them as highly active nematicides. Of the highly active tested compounds, an average octanol/water log P of 0.97 was observed with a range from 0.28 to 2.64, and a Henry's Law constant averaging 2.6 × 10^{? 7} atm.m³/mole. Tested chemicals with minor or low nematicidal activity showed an average log P of 1.76 with a range from 0.15 to 3.42 and a Henry's Law constant averaging 16.6 × 10^{? 7} atm.m³/mole.     

Metabolism of n-C10:0 and n-C11:0 fatty acids by Trichoderma koningii,Penicillium janthinellum and their mixed culture: I. Biomass and CO2 production,and allocation of intracellular lipids

The capacity of two soil fungi, Trichoderma koningii and Penicillium janthinellum, to oxidize n-C_10:0 and n-C_11:0 fatty acids to CO₂ and store intracellular lipids during growth is unknown. This article reports for the first time the metabolism of decanoic acid (DA, C_10:0), undecanoic acid (UDA, n-C_11:0), a mixture of the acids (UDA+DA) and a mixture of UDA+ potato dextrose broth (PDB) by T. koningii and P. janthinellum and their mixed culture. A control PDB complex substrate was used as a substrate control treatment. The fungal cultures were assayed for their capacity to: (1) oxidize n-C_10:0 and n-C_11:0 fatty acids to CO₂ and (2) store lipids intracellularly during growth. On all four fatty acid substrates, the mixed T. koningii and P. janthinellum culture produced more biomass and CO₂ than the individual fungal cultures. Per 150 mL culture, the mixed species culture grown on UDA+PDB and on PDB alone produced the most biomass (7,567 mg and 11,425 mg, respectively). When grown in DA, the mixed species culture produced the least amount of biomass (6,400 mg), a quantity that was lower than those obtained in UDA (7,550 mg) or UDA+DA (7,270 mg). Amounts of CO₂ produced ranged from 210 mg under DA to 618 mg under PDB, and these amounts were highly correlated with biomass (r² = 0.99). Fluorescence microscopy of stained lipids in the mixed fungal cell cultures growing during the exponential phase demonstrated larger fungal cells and higher accumulation of lipids in membranes and storage bodies than those observed during the lag and stationary phases. T. koningii and P. janthinellum grown on n-C_10:0 and n-C_11:0 fatty acids produced lower amounts of biomass and CO₂, but stored higher amounts of intracellular lipids, than when grown on PDB alone.     

Malodor emission characteristics in rendering plants

Odor emission characteristics in rendering plant was studied by measuring 14 kinds of odorants in the emission gases from main processes: cooking of raw bone, concentrating of glue, refining of fat, and drying of bone. The odor from cooker had higher concentration of all odorous components compared with the other processes. From any process except the drying one, there were detected sulfur‐containing odorants in very high concentration. Of the odorants, concentrations of hydrogen sulfide and methyl mercaptan were higher. The odor from drying bed had comparatively low concentration of sulfur‐containing odorants, and higher concentration of ammonia and trimethylamine were detected. Lower fatty acids were detected from all processes though the concentrations were low. In the odorous gases taken at both the emission source and borderline side, high correlations were recognized between organoleptic test value and concentrations of measured odorants.     

Fish products available in Polish market – Assessment of the nutritive value and human exposure to dioxins and other contaminants

Chemical analyses were performed on one hundred and twenty of the most popular varieties of fish products (smoked fish, salted fish, and marinated fish) of the fish market in Poland. The contents of the nutritive substances of fish products (protein, micro- and macronutrients, vitamins A₁, D₃, E, and fatty acids) and the chosen contaminant (toxic metals – mercury, cadmium, lead, arsenic; dioxin/furans – PCDDFs; dioxin-like PCB – dl-PCBs; seven congeners of polybrominated diphenyl ethers – PBDEs; organochlorine pesticides – ΣDDT, HCB, ΣHCH and marker polychlorinated biphenyls – PCB₇) levels were determined. It was confirmed that fish products are a good source of digestible proteins, iodine, selenium, and vitamin D₃. The fundamental nutritive benefit of processed fish lies in its highly beneficial fatty acid composition, which is what imparts them healthy nutritive qualities. The high content of long-chain polyunsaturated fatty acids (LC-PUFAs), which is not noted in other food products, is particularly important.The majority of contaminants studied were present in low levels. The possible threats, particularly in the case of pregnant/nursing women and young children, can pose the levels of dioxin/furans (PCDD/Fs) and dioxin-like (dl-PCBs) in smoked Baltic salmon and smoked sprat, elevated in a relation to particular requirements concerning the content of sum of PCDD/Fs and dl-PCBs in fish (8 pg WHO-TEQ g⁻¹).The health benefits and risks stemming from consumption of fish products were determined according to the Provisional Tolerable Weekly Intake (PTWI) for chosen contaminants (Cd, Hg, As, PCDD/Fs + dl-PCB) and the quantity of ingredients that render a fish diet healthy based on data from the EFSA Journal [EFSA (European Food Safety Authority), 2005. Opinion of the scientific panel on contaminants in the food chain on a request from the European Parliament related to the safety assessment of wild and farmed fish. EFSA J. 236, 1–118]. In regard of high content of LC-PUFAa and other nutritive ingredients, fish products available in Polish market may be considered as healthy food.However, many authors point at contaminants (methylmercury, PCDD/Fs) occurring in fish and fish products as on potential health problem, and emphasize that the amount of that hazardous substances should be limited in human diet.     

Monofluorinated analogues of polychlorinated biphenyls (F-PCBs): synthesis using the Suzuki-coupling, characterization, specific properties and intended use

An improved method, a palladium-catalyzed cross-coupling reaction the so-called Suzuki-coupling, was used to synthesize 19 monofluorinated analogues (F-PCBs) of polychlorinated biphenyls (PCBs), including analogues of PCBs 28, 52 and 81. The coupling of chlorinated and/or fluorinated isomers of aryl boronic acids with bromo- and/or iodobenzenes gave the desired F-PCB congeners in good to excellent yields. The self-coupling product of the aryl boronic acids was the major impurity, but this limitation could be minimized. The influence of ortho-substitution by chlorine on the reaction time was studied in detail. The F-PCBs were characterized by means of ¹H and ¹⁹F NMR and mass spectrometry (MS). F-PCBs show remarkably similar characteristics in many aspects to those of the corresponding non-fluorinated parent PCBs. Since fluorine is generally resistant to degradation, once incorporated into a substrate it functions as an indelible label that can be used to monitor structures and dynamics. F-PCBs may prove their usefulness as markers and tracers in mechanistic and toxicological studies. The aim of further research will be to test the suitability of fluorine as a sensitive probe in a broad range of applications, including synthesis, analytical, mechanistic and toxicological studies.     

Effects of fulvic acid concentration and origin on photodegradation of polycyclic aromatic hydrocarbons in aqueous solution: Importance of active oxygen

With an Xe arc lamp house as simulated sunlight, the influences of fulvic acid (FA) concentration and origins on photodegradation of acenaphthene, fluorine, phenanthrene, fluoranthene and pyrene in aqueous solution have been studied. Similar effects of FAs, collected from five places around China, on polycyclic aromatic hydrocarbon (PAH) photodegradation have been observed. Active oxygen was of significance in PAH photodegradation with the presence of FAs. For systems with 1.25 mg L⁻¹ FAs, the contributions of OH to PAH photodegradation rates were from 33% to 69%. FAs had two opposite effects, i.e., stimulating the generation of active oxygen and advancing PAH photodegradation; competing with PAHs for energy and photons and restraining PAH photodegradation. Generally, photodegradation rates of the 5 PAHs decreased with the increase of FAs concentration; except fluoranthene and pyrene were advanced in solutions with low FA concentration. The influences of FA concentration on PAH photodegradation were more significant than FA origin.     

Evaluation of resin and fatty acid concentration levels by online sample enrichment followed by atmospheric pressure chemical ionization-mass spectrometry (APCI-MS)

Background, aim, and scope  In papermaking, there is a continuous interest both to minimize fresh water consumption and to reduce discharges into the environment. These general trends mean an increase in the amounts of detrimental substances, such as resin and fatty acids, in papermaking process waters. Resin acids, in particular, are responsible for much of the toxicity typically present in paper mill effluents and, for this reason, the routine and rapid monitoring of these compounds in various process streams is necessary. This also means that there is a continuous need to develop straightforward offline and online techniques to clarify problems occurring, for example, as a result of the introduction of more intensively closed systems of water circulation. In the present study, we describe the use of a novel, online, sample enrichment technique followed by atmospheric pressure chemical ionization–mass spectrometry (APCI-MS) suitable for monitoring the concentration levels of common resin and fatty acids in papermaking process waters. Materials and methods  The representative process water samples were taken from the grinding zone of a thermomechanical pulping mill. The samples were first preconcentrated in a precolumn C18, and the analytes were transferred online to MS. The high intensive [M–H]⁻ ion was used for the identification of each analyte since, according to the present ionization method, no other fragmentation was observed. Laboratory-scale, online measurements with an online sample feed were carried out by connecting a centrifugal pump and a ceramic filter to the APCI-MS. Results  Quality parameters, such as repeatability, linearity, and limit of detection (LOD), were determined by using dehydroabietic acid (DHAA) in order to evaluate the suitability of the method for the rapid screening of concentration levels. This method provided satisfactory linearity and a good correlation between analyte concentration and peak area. The suitability of the system for the continuous analysis of the same acids was evaluated in laboratory-scale, online experiments. In all cases, the response to changes in the analyte concentration was linear, and the repeatability of the system was also satisfactory. Discussion  Only a few studies have been published on the analysis of resin and fatty acids with MS techniques. The present method was applied to the monitoring of dehydroabietic, oleic, and stearic acids. The quality parameters were highly comparable with those reported earlier, and the LOD values of the DHAA were below the levels usually encountered in process waters. The quality parameters were only slightly higher than those obtained by the traditional methods of analysis, probably due to the absence of an effective sample clean-up before analysis. Conclusions  The results of the laboratory-scale, online experiments indicated that the online enrichment APCI-MS system is a suitable alternative for monitoring the concentration levels of selected resin and fatty acids in papermaking process waters. The method can be used, for example, to provide useful information about the concentration levels of these acids in different stages of the process, thus signaling possibly impending problems. In general, faster and simpler measurements are needed to meet the requirements for a reduction in fresh water usage in papermaking. Recommendations and perspectives  Compared to the conventional methods used for this purpose, the main benefits of the method are rapidity of measurement, simplicity of use, and absence of the need for multistage sample treatments (short analysis time). For this reason, this online method is more suitable for the control of papermaking by analyzing the concentration levels of interfering substances (i.e., selected resin and fatty acids) than an offline analysis detailing all the individual extractives-based compounds in process streams. It is also obvious that the technique can easily be modified for other environmental pollutants as well.     

Biosynthesis of polyhydroxyalkanoate by Gamma proteobacterium WD-3 from volatile fatty acids

The production of copolymers of poly-β-hydroxyalkanoates (PHA) is generally a high cost process. To reduce the production costs, inexpensive carbon sources such as volatile fatty acids (VFAs) from acidified wastewater can be used. Therefore, isolation of bacterial strains that can produce PHA copolymers using VFAs as a sole carbon source would be a beneficial alternative. In this study, a strain of PHA accumulating bacterium was isolated from the wastewater treatment plant of a soybean processing facility in Harbin. The strain was identified as γ-proteobacterium according to its 16S rDNA information and was originally named as strain WD-3. The strain accumulated a mass of PHA up to 45% of its dry cell weight when it was cultured under the optimum fermentation condition in this study when butyrate was used as the carbon source. In addition, WD-3 could synthesize PHA copolymers of poly-hydroxybutyrate and poly-hydroxyvalerate (PHV) either from C-even substrates or from C-odd substrates, and one-third of the copolymer was PHV. Results from this study demonstrated that small molecule organic acids can be used by the strain of WD-3 as the carbon source for growth and PHA production. The maximum PHA yield in the study was 0.45 g g⁻¹ dry cell.