一体式膜生物反应器中环境条件对混合液粘度的影响研究

文章研究了一体式膜生物反应器中环境条件对混合液粘度的影响,以及混合液粘度对膜过滤阻力的影响。试验结果表明：混合液的粘度主要是由胞外聚合物引起的;混合液粘度随着胞外聚合物含量的变化而变化;混合液粘度与各操作条件之间存在一定的关系U=1．586（MESS）^0．614T^-0.106（DO）^0.4697;混合液粘度与膜过滤阻力有较好的相关性。     

Evaluation of factors influencing soluble microbial product in submerged MBR through hybrid ASM model

In this study, a mathematical model was established to predict the formation of the soluble microbial product (SMP) in a submerged membrane bioreactor. The developed model was calibrated under the reference condition. Simulation results were in good agreement with the measured results under the reference condition. The calibrated model was then used in the scenario studies to evaluate the effect of three chosen operating parameters: hydraulic retention time (HRT), dissolved oxygen concentration, and sludge retention time (SRT). Simulation results revealed that the SMP dominated the soluble organic substances in the supernatant. The scenario studies also revealed that the HRT can be decreased to 1 h without deteriorating the effluent quality; dissolved oxygen concentration in the reactor can be kept at 2–3 mg/L to maintain the effluent quality, reduce the content of SMP, and minimize operating costs; the optimal SRT can be controlled to 10–15 d to achieve complete nitrification process, less membrane fouling potential, and acceptable organic removal efficiency.     

Biodegradation of trace pharmaceutical substances in wastewater by a membrane bioreactor

The biodegradation of selected pharmaceutical micropollutants, including two pharmaceuticals with argued biodegradation, was studied by a lab-scale membrane bioreactor. The reaction kinetics and affecting factors were also investigated in this paper. Clofibric acid (CA) with contradictive biodegradation reported was degraded almost completely at different hydraulic retention times (HRTs) after adaptation to microorganisms. The biodegradation of CA was disturbed at low pH operation, while the activity of microorganisms recovered again after pH adjustment to neutral condition. Ibuprofen (IBP) degraded under neutral and acidic conditions. Removals of IBP and CA were zero-order and first-order reactions under high and low initial concentrations, respectively. Carbamazepine and diclofenac were not degraded regardless of HRTs and pH.     

膜生物反应器在屠宰废水中的应用

介绍了平板膜生物反应器在屠宰废水工程的应用实例。实践表明,膜生物反应器技术适合处理屠宰废水,具有工艺流程简单,处理效果好,处理后的废水可以回用,运行稳定和基建投资低等优点。     

浸入式超滤膜工艺稳定运行影响因素研究

以确定浸入式超滤膜工艺稳定运行工况为目标,进行了混凝.浸入式超滤膜工艺处理滦河原水的中试研究.采用横跨膜压差(TMP)做为表征膜稳定运行的工艺参数,考察了膜通量、制水周期、原水水质条件的改变对膜工艺的影响.结果表明,采用浸入式膜处理滦河水时,膜通量为53.3 L/(m2·h)且制水周期为30 min时膜工艺运行稳定,能较好控制膜污染;水温变化对膜工艺运行影响较大,低温期单个过滤周期TMP比高藻期增加了76%;EFM和化学清洗结合是一种有效地控制膜污染、强化稳定运行的措施.     

纳滤膜过滤MBR出水的污染原因与清洗方法

为研究膜-生物反应器(MBR)出水对纳滤膜的污染原因及清洗方法,使用场发射扫描电镜、傅立叶变换红外光谱仪、原子力显微镜和接触角仪对经MBR出水污染的纳滤膜表面污染层进行了检测,结果表明,纳滤膜表面污染物包括有机物和无机物,所含元素包括磷、镁等,对经过不同清洗步骤的膜表面进行的检测表明,柠檬酸清洗可以去除镁和大部分磷,这些物质主要以无机形态存在于膜面污染物中;后续NaOH清洗可以进一步去除磷,这部分磷主要来自有机酸、有机磷或蛋白质等膜面污染物.污染使膜表面粗糙度由79.5 nm增大至111.2 nm,但接触角由55.6°变为62.1°,表明亲水性变化不大;酸洗后表面粗糙度显著减小至51.9 nm,接触角变为96.0°,表明有机污染物暴露出来,膜面呈现疏水性;再经碱洗后,膜面粗糙度与亲水性均接近于新膜.这些结果说明,先酸洗后碱洗的方法可以去除绝大部分的膜面污染物,进一步推知膜污染初期主要为有机污染,之后无机物的作用使污染进一步加重.     

Simulation and assessment of sludge concentration and rheology in the process of waste activated sludge treatment

The process of using flat-sheet membrane for simultaneous sludge thickening and digestion (MSTD) was employed. The variations of sludge concentration and rheology were characterized and simulated. Based on mass balance analysis, mathematical models were developed and successfully used to predict and evaluate the variations of sludge concentration and the digestion e ciency in the MSTD process. The apparent viscosity of sludge could be modeled as functions of mixed liquor suspended solids and shear rates. The sludge in the MSTD process showed both shear-thinning and viscoplastic behaviour, and under various shear rates di erent rheological models could be chosen to predict their flow behaviour. It was also found that sludge concentration and viscosity had significant correlations with membrane fouling in the MSTD process.     

表面覆膜多层复合纤维滤料过滤性能的数值研究

根据Matlab软件和数值计算前处理软件Gambit中的Journal文件建立了多层复合纤维滤料模型,利用计算流体动力学(CFD)技术对沿气流方向具有不同纤维填充密度及直径分布的滤料内部的气-固两相流动特性进行了数值研究,计算了不同运行条件下滤料的压力损失及过滤效率,并将数值计算值和经典模型及实验关联式的计算值进行了比较.结果表明,压力损失的数值计算预测值和实验关联式计算值吻合较好,误差在2%以内.随着迎面风速的增加,压力损失呈线性增加.相对于填充密度,纤维直径对压力损失和过滤效率的影响更显著.不同结构滤料过滤效率的数值计算结果和理论模型的计算值变化趋势基本一致.不同迎面风速下,过滤效率都是先减小后增大,对于颗粒直径dp≤0.05μm的颗粒,随着风速的增大,过滤效率减小;对于dp≥0.5μm的颗粒,过滤效率变化趋势正好相反.迎面风速不同,过滤效率最低点出现的位置也不同.对于小颗粒,风速越小,扩散作用起主导作用;而对于大颗粒,风速越大,惯性作用越明显.过滤效率最低点出现在扩散作用逐渐弱化,惯性作用刚刚开始加强的区域.多层复合滤料在结构上采用纤维直径逐层加大的梯次结构时,能够获得较高的过滤效率.而在多层复合滤料表面覆膜后过滤效率平均增加约13%.     

O_3-MBR法深度处理煤气废水

以经多级生物处理后的煤气废水为原水,采用O3-MBR组合工艺对其进行深度处理,以满足回用要求.结果表明:采用臭氧氧化工艺,当废水pH为11和臭氧投加量〔ρ(臭氧)〕为189.2mg/L时,CODCr和色度的去除率分别为46.5%和80.2%,ρ(BOD5)/ρ(CODCr)由0.02升至0.29,废水的可生化性得到明显改善;臭氧氧化工艺出水再通过MBR作进一步处理,CODCr,NH3-N和色度的去除率分别达23.0%,76.3%和70.0%,且出水水质稳定;总体上,废水经O3-MBR组合工艺处理,CODCr,NH3-N,色度和浊度的平均总去除率分别达到58.7%,76.3%,88.6%和95.1%;处理后出水的ρ(CODCr)50mg/L,ρ(NH3-N)5mg/L,浊度0.2NTU,色度约为30度,出水水质满足生产工艺回用的要求.     

臭氧对膜法水处理中膜污染的影响

膜过滤是一种高效水处理技术,包括污水处理中的膜-生物反应器（membrane bioreactor,MBR）和针对二级生物处理出水（生产再生水）、地表水（生产饮用水）的膜过滤工艺等,其中膜污染是制约膜工艺应用的一个主要问题.臭氧具有强氧化性,在水处理上得到了广泛的应用.近十几年来,针对臭氧-膜过滤组合工艺的研究正变得越来越多,因此本文对这些研究进行了系统综述与分析.在MBR组合臭氧控制膜污染方面的研究中,目前结论相对较少.可以通过对MBR进水预臭氧化或者投加适量臭氧到MBR混合液这2种方式来减轻MBR膜污染.在针对微污染水的臭氧-膜过滤组合工艺中,根据臭氧的功能和结构形式主要分为3种,分别是污染膜臭氧清洗、分离式臭氧-膜工艺和一体式臭氧-膜工艺.绝大部分报道认为臭氧可以有效地控制膜污染的发展,但也有少数投加臭氧后膜污染加剧的情况.目前,臭氧化影响膜污染机制的研究主要集中在有机物方面,根据原水水质和工艺结构参数等的不同,颗粒物、微生物和无机物质也在这个过程中起着相应的作用.另外,在迄今为止的研究中,还缺乏对于臭氧投加方式和分散方式的统一衡量和比较标准.作者建议应该加强对一体式臭氧-膜组合工艺的研究,并且要注意臭氧投加的工艺经济性.