云南宣威地区燃煤排放PM10的微观形貌和粒度特征

宣威地区肺癌发病率居全国首位,并且肺癌与室内燃煤关系密切. 为了解宣威地区室内燃煤排放PM₁₀的微观形貌和粒度特征,使用小流量Minivol采样器,分别于2011年1月、3月和12月对宣威地区6个代表性乡镇的18个农户及对照点——贵州六盘水幸福村2个农户室内、外的PM₁₀进行采样. 采用扫描电子显微镜分析样品的微观形貌,并对颗粒物粒度进行统计分析. 根据微观形貌特征将PM₁₀分为烟尘集合体(链状、蓬松状、密实状)、球形颗粒(燃煤飞灰和焦油球)、矿物颗粒(规则和不规则状)、生物颗粒及超细未知颗粒. 结果表明:宣威地区室内PM₁₀微观形貌差别较大;室、内外PM₁₀的粒度分布在0.1~0.4μm内的颗粒数量所占比例较大,而1μm以上颗粒体积所占比例较大;小粒径颗粒对颗粒物数量贡献较大,而少数大粒径颗粒对体积贡献较大;宣威地区和对照点室内的PM₁₀数量-粒度和体积-粒度分布相似,室外PM₁₀数量-粒度特征相似但体积-粒度分布有所差异. 宣威地区室内的烟尘集合体和球形颗粒分别占颗粒物总数的10.5%和23.6%,高于对照点 (分别为7.7%和11.3%).      

细微泥沙对活性污泥系统的影响及其恢复特征

不同地区、排水体制和季节下,我国城市污水厂进水中细微泥沙含量〔以ρ(ISS)/ρ(COD_Cr)表征,ISS为无机悬浮固体〕差异较大,细微泥沙进入生化处理单元将会对活性污泥系统的正常运行产生一定影响. 考察在不同进水细微泥沙浓度下,活性污泥系统各运行参数的变化及系统恢复情况,结果表明:①随着进水中细微泥沙浓度的增大,活性污泥系统ρ(MLVSS)/ρ(MLSS)、SOUR′(单位质量污泥活性)、CST(污泥毛细吸水时间)和SVI(污泥容积指数)降低;在影响期,ρ(MLVSS)/ρ(MLSS)最小值、SOUR′平均值、CST平均值与细微泥沙浓度均呈良好的线性关系,R2(相关系数)分别为0.963 7、0.979 9和0.786 5;系统恢复所需时间与进水细微泥沙浓度呈正相关. ②污泥中细微泥沙浓度的增加导致SOUR′下降,使得ρ(MLSS)和剩余污泥量增加,不利于污水厂的节能减排. 可见进水中细微泥沙浓度的增大不利于污水厂的稳定高效运行.      

Using multivariate regression modeling for sampling and predicting chemical characteristics of mixed waste in old landfills

Municipal solid waste landfills pose a threat on environment and human health, especially old landfills which lack facilities for collection and treatment of landfill gas and leachate. Consequently, missing information about emission flows prevent site-specific environmental risk assessments. To overcome this gap, the combination of waste sampling and analysis with statistical modeling is one option for estimating present and future emission potentials. Optimizing the tradeoff between investigation costs and reliable results requires knowledge about both: the number of samples to be taken and variables to be analyzed.This article aims to identify the optimized number of waste samples and variables in order to predict a larger set of variables. Therefore, we introduce a multivariate linear regression model and tested the applicability by usage of two case studies. Landfill A was used to set up and calibrate the model based on 50 waste samples and twelve variables. The calibrated model was applied to Landfill B including 36 waste samples and twelve variables with four predictor variables.The case study results are twofold: first, the reliable and accurate prediction of the twelve variables can be achieved with the knowledge of four predictor variables (Loi, EC, pH and Cl). For the second Landfill B, only ten full measurements would be needed for a reliable prediction of most response variables. The four predictor variables would exhibit comparably low analytical costs in comparison to the full set of measurements. This cost reduction could be used to increase the number of samples yielding an improved understanding of the spatial waste heterogeneity in landfills.Concluding, the future application of the developed model potentially improves the reliability of predicted emission potentials. The model could become a standard screening tool for old landfills if its applicability and reliability would be tested in additional case studies.     

Elevated CO2 changes the moderate shade tolerance of yellow birch seedlings

To demonstrate the existence of light thresholds in plant growth and to examine the effects of elevated CO2 on the shade tolerance of a tree species, an experiment consisting of a completely randomized design for a total of 96 yellow birch (Betula alleghaniensis Britton) seedlings was conducted with 3 light levels (2.9%, 7.7%, 26.1% of full sunlight)×2 CO2 levels (350 and 700±10 ppm) with 4 replications in a phytotron. The study proved that thresholds exist and they vary in different plant organs. In ambient CO2, the thresholds were 13.3%, 18.7%, 15.0%, 15.2%, and 15.6% of full sunlight for stem, leaf, root, total plant biomass, and the averaged value, respectively. In 700 ppm CO2, the corresponding thresholds were 16.7%, 21.3%, 18.1%, 21.7% and 19.5% for stem, leaf, root, total plant biomass, and the averaged value, respectively. The lowest threshold in the stem is an indicator of the minimal light intensity for regular growth for seedlings of this species. Below this threshold, light-stressful growth occurs. The result of a paired t-test indicated that the thresholds in elevated CO2 were significantly higher than in ambient CO2. This suggests that yellow birch will lose its moderate shade tolerance, evolutionally becoming a shade-intolerant species, and that it may become more difficult to naturally regenerate in the future.     

水稻耐氨固氮菌施用效应研究

早、晚两季的田间试验结果表明,在电脑推荐施N水平上,耐氨固氮菌的增产效果不显著;在低N情况下(每公顷减纯N37.5kg),耐氨固氮菌的增产效果达显著水平,早、晚稻分别增产8.41％和7.21％。15N示踪盆栽试验结果表明,耐氨固氮菌对根系生长有明显的促进作用,在秧苗期明显增加秧苗对肥料15N的吸收．禾苗分蘖盛期则增强了禾苗根系的吸氮能力。     

温度变化对不同污泥形态厌氧氨氧化菌活性的影响

以Ca. Brocadia为主要种属的厌氧氨氧化颗粒污泥和生物膜为研究对象,通过测定不同温度下厌氧氨氧反应活化能以探讨温度对以不同污泥形态存在的厌氧氨氧化菌的短期影响。结果表明,在15~25 ℃和25~35 ℃,以颗粒污泥及生物膜形态存在的厌氧氨氧化菌的反应活化能不同。在15~25 ℃,颗粒污泥和生物膜中的厌氧氨氧化反应活化能分别为105.60 kJ·mol⁻¹和88.25 kJ·mol⁻¹,而在25~35 ℃,对应的活化能分别为62.15 kJ·mol⁻¹和56.78 kJ·mol⁻¹,均低于同温度条件下以游离态存在的厌氧氨氧化菌的反应活化能。这说明不同污泥形态对Anammox菌的温度效应不同,以生物膜和颗粒污泥形态存在的厌氧氨氧化菌具有较强抵抗温度变化的能力。在15~25 ℃,颗粒污泥和生物膜中厌氧氨氧化菌的温度系数θ分别为1.14和1.12,在25~35 ℃,对应的温度系数θ分别为1.09和1.08。与硝化菌或反硝化菌相比,厌氧氨氧化菌的温度系数$ \theta $偏大。这表明厌氧氨氧化菌对温度的变化更为敏感,使得厌氧氨氧化在低温条件下首先将成为限制步。     

超级钢闪光对焊电热耦合过程温度场分布的有限元分析

为研究超级钢闪光对焊闪光阶段焊件的温度场分布 ,建立了轴对称有限元模型。运用单元死活技术解决闪光时液体过梁爆破引起物质烧损的模拟问题 ,提出了闪光焊过程中电热耦合作用的模拟方法。考虑单元死活的有限元分析结果与试验结果更加吻合 ,为选择和优化闪光焊焊接参数以及为闪光焊过程顶锻阶段的热力耦合过程的模拟提供了有效的分析手段     

小陇山林区主要森林群落凋落物及死木质残体储量

采用固定面积样方取样法研究了小陇山林区锐齿栎和油松天然林死木质残体及凋落物的总储量.结果表明:小陇山林区锐齿栎天然林粗死木质残体(Coarse woody debris,简称CWD)和细小木质残体(Fine woody debris,简称FWD)储量分别为29 350.92 kg hm-2和2 298.41 kg hm-2,分别为油松天然林的3.8和1.3倍.油松林CWD组成中枯立木占到85.65%,倒木只占14.35%,而锐齿栎天然林枯立木和倒木所占的比例基本为1.从CWD的径级结构上来说,锐齿栎林内以大径级CWD为主(≥20 cm),占样地CWD总储量的60.81%,天然油松林以小径级(20 cm≥小径级≥10 cm)CWD为主,大、小径级分别占CWD储量的55.33%和44.67%.油松林内凋落物储量为30 472.31 kg hm-2,是天然锐齿栎凋落物储量8 902.29 kg hm-2的3倍以上.凋落物和死木质残体储量的不同是锐齿栎天然林和油松天然林种群结构、林分更新和群落内部竞争状况及凋落物分解状况差异所导致的结果.     

湿法脱硫系统对烟气中可吸入颗粒物特性影响的实验研究

采用荷电低压颗粒冲击器对4套湿法烟气脱硫(WFGD)系统进出口颗粒物进行在线检测和采样分析,获得烟气中PM10、PM2.5质量浓度以及粒径分布特征,并通过场发射扫描电镜(FESEM)和元素能谱对飞灰颗粒的形貌特征和主要元素含量进行分析。实验结果表明,由于脱硫塔喷淋浆液的洗涤作用,WFGD系统对飞灰颗粒有一定的脱除效果,但喷淋浆液产生的小液滴以及石灰石/石膏颗粒被携带进入烟气,导致WFGD系统对烟气中颗粒物质量浓度及粒径分布影响较大。WFGD系统对飞灰颗粒组成成分也有一定影响,以WFGD系统B为例,出口飞灰颗粒中Ca和S的质量分数从进口的1.60%、2.81%上升到出口的6.12%、10.92%。FESEM观察结果表明,脱硫后小颗粒在脱硫浆液的促进作用下团聚凝并,形成大颗粒,呈现致密的不规则块状、层状或絮状结构。     

黑炭气溶胶质谱仪(SP-AMS)分析春季PM2.5中水溶性有机气溶胶

为探讨常州春季大气细颗粒物(PM_2.5)的化学组成及污染特征,于2017年3月1日～5月30日采集了84个有效样品,对其水溶性离子(WSIIs)、碳质组分(OC和EC)等常规组分进行了测定和分析,并采用黑炭-气溶胶质谱仪(SP-AMS)对水溶性有机气溶胶(WSOA)进行了分析.结果表明,采样期间PM_2.5的日均质量浓度为101. 97μg·m^-3,超标(环境空气质量标准二级标准)率达73. 8%,以轻度、中度和重度污染为主,分别占总天数的39. 3%、21. 4%和13. 1%. WSIIs约占PM_2.5的39. 86%,其中二次离子(SO₄^2-、NH₄⁺和NO₃^-)占WSIIs的81. 85%,阴阳离子电荷平衡的线性拟合直线的斜率(AE/CE)大于1(1. 09),表明PM_2.5偏弱酸性. OC/EC比值为2. 53,说明受二次转化的影响. SP...