外源硅对不同pH水田土壤吸附铅的影响

通过等温吸附实验,研究了加硅对2种不同pH水田土壤吸附铅特性的影响。实验中用硝酸中和硅酸钠的碱性,各处理间钠离子和硝酸根离子的差异以硝酸钠补齐,消除了因硅酸盐的加入改变体系pH及伴随离子对土壤吸附铅可能产生的影响。结果表明,在本实验条件下,Langmuir方程、Freundlich方程和Temkin方程都能较好地描述不同硅浓度条件下两种土壤对铅的吸附特征,但以Freundlich模型为最优;加硅促进了酸性土壤对铅的吸附,抑制了碱性土壤对铅的吸附。     

Combining sap flow and eddy covariance approaches to derive stomatal and non-stomatal O3 fluxes in a forest stand

Stomatal O₃ fluxes to a mixed beech/spruce stand (Fagus sylvatica/Picea abies) in Central Europe were determined using two different approaches. The sap flow technique yielded the tree-level transpiration, whereas the eddy covariance method provided the stand-level evapotranspiration. Both data were then converted into stomatal ozone fluxes, exemplifying this novel concept for July 2007. Sap flow-based stomatal O₃ flux was 33% of the total O₃ flux, whereas derivation from evapotranspiration rates in combination with the Penman-Monteith algorithm amounted to 47%. In addition to this proportional difference, the sap flow-based assessment yielded lower levels of stomatal O₃ flux and reflected stomatal regulation rather than O₃ exposure, paralleling the daily courses of canopy conductance for water vapor and eddy covariance-based total stand-level O₃ flux. The demonstrated combination of sap flow and eddy covariance approaches supports the development of O₃ risk assessment in forests from O₃ exposure towards flux-based concepts.     

钢渣吸附处理苯酚废水的研究

采用恒温振荡的方法,考察了钢渣粒径、吸附温度、振荡速度、溶液pH值、溶液初始浓度对苯酚去除率的影响。结果表明,在粒径为120~180目、pH=4.0、苯酚溶液浓度在500 mg/L以内、苯酚/钢渣质量比为1∶1 000时吸附效果最好。钢渣对苯酚的吸附能较好地符合Langmuir和Freundlich吸附等温线,线性相关系数分别为0.9971和0.9916,吸附机理为表面吸附。     

共代谢基质对芽孢杆菌Y-4降解异喹啉的影响

以吡啶,葡萄糖和邻苯二甲酸作为共代谢基质,研究了它们对芽孢杆菌Y_4降解异喹啉的影响。实验结果表明各降解过程均遵循二级反应动力学方程：-dS／dt=K2S2＋K1S＋K0。吡啶的加入会抑制异喹啉的降解,并且吡啶的浓度越高,抑制作用越明显。反应体系中葡萄糖的浓度为100-800mg／L时,葡萄糖的加入会促进异喹啉的降解,且葡萄糖浓度越大,异喹啉降解速率P越大,当葡萄糖的浓度为800mg／L时,其降解率速率P可由未加葡萄糖的0．1924h。上升为0．2255h-1。适宜浓度的邻苯二甲酸会对异喹啉的降解产生促进作用,邻苯二甲酸的浓度为50mg／L时,异喹啉的降解速率可由原来的0．1924h-1增加到0．2145h-1,邻苯二甲酸浓度过高反而会抑制异喹啉的降解。     

Use of fugacity model to analyze temperature-dependent removal of micro-contaminants in sewage treatment plants

Effluents from sewage treatment plants (STPs) are known to contain residual micro-contaminants including endocrine disrupting chemicals (EDCs) despite the utilization of various removal processes. Temperature alters the efficacy of removal processes; however, experimental measurements of EDC removal at various temperatures are limited. Extrapolation of EDC behavior over a wide temperature range is possible using available physicochemical property data followed by the correction of temperature dependency. A level II fugacity-based STP model was employed by inputting parameters obtained from the literature and estimated by the US EPA’s Estimations Programs Interface (EPI) including EPI’s BIOWIN for temperature-dependent biodegradation half-lives. EDC removals in a three-stage activated sludge system were modeled under various temperatures and hydraulic retention times (HRTs) for representative compounds of various properties. Sensitivity analysis indicates that temperature plays a significant role in the model outcomes. Increasing temperature considerably enhances the removal of β-estradiol, ethinyestradiol, bisphenol, phenol, and tetrachloroethylene, but not testosterone with the highest biodegradation rate. The shortcomings of BIOWIN were mitigated by the correction of highly temperature-dependent biodegradation rates using the Arrhenius equation. The model predicts well the effects of operating temperature and HRTs on the removal via volatilization, adsorption, and biodegradation. The model also reveals that an impractically long HRT is needed to achieve a high EDC removal. The STP model along with temperature corrections is able to provide some useful insight into the different patterns of STP performance, and useful operational considerations relevant to EDC removal at winter low temperatures.     

Vertical migration of radionuclides in undisturbed grassland soils

Literature data on numerical values obtained for the parameters of the two most popular models for simulating the migration of radionuclides in undisturbed soils have been compiled and evaluated statistically. Due to restrictions on the applicability of compartmental models, the convection–dispersion equation and its parameter values should be preferred. For radiocaesium, recommended values are derived for its effective convection velocity and dispersion coefficient. Data deficiencies still exist for radionuclides other than caesium and for soils of non-temperate environments.     

HYDROLOGIC MODELING OF A BIOINFILTRATION BEST MANAGEMENT PRACTICE1

ABSTRACT: The goal of this research was to develop a methodology for modeling a bioinfiltration best management practice (BMP) built in a dormitory area on the campus of Villanova University in Pennsylvania. The objectives were to quantify the behavior of the BMP through the different seasons and rainfall events; better understand the physical processes governing the system's behavior; and develop design criteria. The BMP was constructed in 2001 by excavating within an existing traffic island, backfilling with a sand/soil mixture, and planting with salt tolerant grasses and shrubs native to the Atlantic shore. It receives runoff from the asphalt (0.26 hectare) and turf (0.27 hectare) surfaces of the watershed. Monitoring supported by the hydrologic model shows that the facility infiltrates a significant fraction of the annual precipitation, substantially reducing the delivery of nonpoint source pollution and erosive surges downstream. A hydrologic model was developed using HEC‐HMS to represent the site and the BMP using Green‐Ampt and kinematic wave methods. Instruments allow comparison of the modeled and measured water budget parameters. The model, incorporating seasonally variable parameters, predicts the volumes infiltrated and bypassed by the BMP, confirming the applicability of the selected methods for the analysis of bioinfiltration BMPs.     

CRITICAL EVALUATION OF CERTAIN METHODS OF UNSTEADY GROUNDWATER HYDRAULICS1

The basic theories and fundamental assumptions usually employed in the solution of unsteady groundwater flow problems are reviewed critically. The best known method of analysis for such problems is based on the Dupuit-Forchheimer approximation and leads to a nonlinear parabolic differential equation which is generally solved by linearization or numerical methods. The accuracy of the solution to this equation can be improved by use of a different approach which does not employ the Dupuit Forchheimer assumption, but rather is based on a semi-numerical solution of the Laplace equation for quasi-steady conditions. The actual unsteady process is replaced by a sequence of steady-state conditions, and it is assumed that the actual unsteady flow characteristics during a short time interval can be approximated by those associated with “average” steady state flow. The Laplace equation is solved by a semi-discretization method according to which the horizontal coordinate is divided into subintervals, while the vertical coordinate is maintained continuous. The proposed method is applied to a typical tile drainage problem, and, based on a comparison of calculated results with experimental data, the method is evaluated and practical conclusions regarding its applicability are advanced.     

DIGITAL SIMULATION OF THE EFFECT OF THERMAL DISCHARGE ON STREAM WATER QUALITY1

A modified transient version of the Streeter-Phelps model along with the energy balance equation is employed to analyze the effects of waste heat discharge from power plants on stream water quality. Analysis is also made to examine the effects of the upstream water quality and stream velocity on the downstream DO concentration level. The resulting coupled nonlinear hyperbolic partial differential equations representing the energy, BOD and DO concentrations are solved by the method of characteristics and simulated on a digital computer. Final numerical results indicate that the allowable quantity of thermal discharge does heavily depend on the upstream quality.     

STABILITY AND REACH LENGTH IN WATER SURFACE PROFILE DETERMINATION1

ABSTRACT: Extension of basic step methods of backwater computation to reaches of finite length is examined. Accuracies of commonly accepted hydraulic loss equations under particular water surface profile conditions are compared. Simulation of energy lines within a reach by parabolic curves is found to minimize error provided orientation of the axis of the parabola is selected in accordance with prevailing hydraulic conditions. Theoretical basis for an index reach length beyond which single-step computation from end to end of the reach must be in error is developed. Reduction of this reach length by suitable factors tailored to hydraulic conditions yields a mathematically defined allowable reach length for backwater computation. When reach length does not exceed this allowable reach length, no significant error may be detected. Automatic insertion of synthetic cross sections interpolated between surveyed cross sections when these are inadvertently spaced too far apart enables computation to proceed. This device is error-free for prismatic channls but may introduce error for irregular natural channels. Preliminary trials indicate that results so obtained may be accepted provided the fall in the original reach does not exceed from one to two feet. When this is exceeded, additional cross sections should be surveyed.