北京市餐饮业大气污染物排放特征

餐饮业是中国大型城市大气环境污染源之一.为了解餐饮业大气污染物的产生能力,本研究以北京为研究对象,选取41家不同菜系的餐饮企业,现场实地检测了净化设备前端的油烟、颗粒物和非甲烷总烃(NMHC)的产生浓度水平.结果表明,净化前油烟、颗粒物和NMHC的初始平均浓度约为1.93、 6.6和10.9 mg·m^-3.提出了一种基于工作日与非工作日的估算污染物排放总量的计算方法.并基于北京市餐饮企业数量和本研究测得的排放因子,初步估算了2019年全市餐饮源主要污染物的初始产生总量,油烟、颗粒物和NMHC的年排放总量分别为5 512、 18 849和6 169 t.川湘菜、烧烤、烤鸭与家常菜产生的油烟与颗粒物浓度的Pearson系数均>0.6,具有强相关性;其中川湘菜和烤鸭排放的Pearson系数均>0.8,呈现极强相关性.     

烹调油烟对DNA和细胞的损伤

综述了烹调油烟的成分及对DNA和细胞的损伤，提出了降低居室内烹调油烟的措施。     

等离子体协同MnOx/SBA-15催化降解正己醛的研究

采用浸渍法制备了MnOx/SBA-15催化剂,利用BET、XRD和SEM等对催化剂进行表征。考察了介质阻挡放电等离子体协同MnOx/SBA-15催化剂对正己醛的降解性能。结果显示,负载MnOx后的SBA-15仍然保持介孔结构,且MnOx均匀地分散在SBA-15中;等离子体与催化剂表现出较好的协同作用,干燥条件下7.5 kV的放电电压结合10%MnOx/SBA-15时降解效果最佳,正己醛去除率达99%;相比干燥条件,相对湿度低于20%时正己醛去除率变化不明显,但高于20%时催化效果明显下降;该催化剂具有很强的O3分解能力,O3在催化剂表面的分解不仅促进了正己醛的氧化,同时也提高了CO2的选择性。     

液体节煤固硫添加剂对锅炉排污的影响研究

通过对在同一种原煤上使用液体节煤固硫添加剂前、后锅炉废气的对比测试,分析了加入添加剂后锅炉排放废气中烟尘粒径、烟尘浓度、二氧化硫、氮氧化物浓度等变化的原因及趋势。结果表明,在使用液体节煤固硫添加剂后,锅炉排放废气中烟尘、二氧化硫浓度均有显著降低,氮氧化物浓度基本不变,排放烟尘粒径呈现由较大向较小转化的趋势。     

饮食业油烟污染与处理技术研究

分析了油烟中的主要污染物成分，介绍了油烟对人体健康的几种危害，并对现有的五种处理技术：惯性分离、过滤分离、洗涤去除、静电沉积、复合技术进行了详尽的分析比较，列举了一些应用实例。     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N2吸附-脱附曲线、FT—IR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu2＋的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869．5m。／g,孔容为0．97cm3／g,平均孔径为3．3nm;溶液pH为5—6时,MCM-41对Cu2＋的去除效果最好;MCM-41对Cu3＋的最大吸附吸附容量36．3mg／g;MCM-41对Cu2＋的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

饮食业油烟净化工艺的新探索

针对饮食业厨房油烟组成及污染特点 ,在比较现有净化技术优缺点的基础上 ,提出了雾化湿法与过滤吸附相结合的油烟净化新工艺 ,且对油烟净化方法进行了新的探索。试验结果表明 :雾化湿法与过滤吸附相结合的净化工艺对油烟的去除效率在 92 %以上 ,净化后的油烟排放浓度符合国家标准 ,适合中、小型餐馆使用。     

Analysis of welding fumes: A short note on the comparison between two sampling techniques

It is well established that welding fumes contain toxic substances, and that its composition is dependent on multiple factors, such as nature of the welding process and chemical compositions of the welding consumables and base materials. In order to prevent accidents and, thus to contribute to the safety of protection of welders, the establishment of a database on welding fume components is considered as essential. This has led to the development and upgradation of sampling techniques of welding fumes. Up to now, few standard techniques exist in this area. This study describes the results of the analysis of welding fumes, in terms of heavy metals, for a set of welding electrodes commonly used in carbon steel manufacture. Sampling was done by two different techniques: using the one currently known as “fume box” and common techniques in workplace atmospheres.     

Assessment of the effect of welding fumes on welders’ cognitive failure and health-related quality of life

Introduction. This study examined whether cognitive symptoms and health-related quality of life can be affected by welding fume exposure. Method. Participants consisted of welders (n?=?40) and welder assistants (n?=?25) from welding units as the exposed group, and office workers (n?=?44) as the non-exposed group. All participants were studied using ambient air monitoring and two types of questionnaires: the Cognitive Failures Questionnaire (CFQ) and the 36-item Short Form Health Survey (SF-36). Results. Welders and welder assistants were exposed to higher concentrations of all airborne metals than office employees, except for aluminum and chromium (p?p?M (SD)?=?54.84 (17.88)). The relationships between total CFQ score and the measured concentration of nickel at peak work rate was significant for welders. Conclusion. Cognitive symptoms and health-related quality of life were not related to the measures of welding fume exposure and further research should be performed to find other influencing factors.     

转炉二次烟气除尘变工况及风机调速

根据转炉二次烟气除尘风量随冶炼周期变化的特征,利用工艺设备工况特征信号控制各除尘阀门的开闭,并根据各个除尘分支管道工况的变化,确定系统在不同工作点的总阻力、风量和风机转速,达到自动控制风机调速,节约电能的目的。