中铝洛铜熔铸厂16吨黄铜炉组除尘系统改造

通过对中铝洛铜熔铸厂16t黄铜炉组除尘系统出现的问题采取相应对策进行改造,探讨了通过屋顶罩排烟系统来解决黄铜炉组炉盖开启操作时产生大量烟尘的方法,具有实用性,同时针对黄铜炉熔炼产生烟尘的特点,提出了适合氧化锌回收的除尘改造方案.     

电捕法净化焙烧炉沥青烟气

针对炭素焙烧炉烟气特点,采用雾化水预处理和电捕焦油技术,对某炭素厂焙烧炉烟气进行治理,达到既高效净化有害气体,又降低资金投入。处理后的烟气指标为:沥青烟浓度13.8mg/m3,苯并(a)芘浓度0.053×10-3mg/m3,烟尘浓度19.1mg/m3,各项污染物均达标排放。     

酸浸粉煤灰混凝法处理制革废水的研究

笔者研究了在热电厂粉煤灰中加入少量的鼓风炉铁泥和适量的助溶剂HS,在加热条件下用稀硫酸搅拌浸取2h后,制得集物理吸附和化学混凝为一体的混凝剂。这种混凝剂与聚硅酸铝铁(PSAF)絮凝剂配合处理COD为1500～2000mg/L制革废水,SS,COD,硫化物和铬的去除率分别为95%,93%,92%和88%。该法的显著特点是混凝沉降速度快,污泥体积小,处理废水费用低,此外还探讨了酸浸粉煤灰混凝剂对制革废水的混凝沉降机理。      

闪速炉烟尘收尘装置的改造

简要概述了闪速炉气力输送系统收尘装置的改造和圆筒型布袋收尘装置在气力输送系统中使用的效果.     

Removal kinetics of phosphorus from synthetic wastewater using basic oxygen furnace slag

Removal kinetics of phosphorus through use of basic oxygen furnace slag (BOF-slag) was investigated through batch experiments. Effects of several parameters such as initial phosphorus concentration, temperature, BOF-slag size, initial pH, and BOF-slag dosage on phosphorus removal kinetics were measured in detail. It was demonstrated that the removal process of phosphorus through BOF-slag followed pseudo-first-order reaction kinetics. The apparent rate constant (k_obs) significantly decreased with increasing initial phosphorus concentration, BOF-slag size, and initial pH, whereas it exhibited an opposite trend with increasing reaction temperature and BOF-slag dosage. A linear dependence of k_obs on total removed phosphorus (TRP) was established with k_obs = (3.51 ± 0.11) × 10^− 4 × TRP. Finally, it was suggested that the Langmuir–Rideal (L–R) or Langmuir–Hinshelwood (L–H) mechanism may be used to describe the removal process of phosphorus using BOF-slag.     

Removal kinetics of phosphorus from synthetic wastewater using basic oxygen furnace slag

Removal kinetics of phosphorus through use of basic oxygen furnace slag(BOF-slag)was investigated through batch experiments. Effects of several parameters such as initial phosphorus concentration, temperature, BOF-slag size, initial p H, and BOF-slag dosage on phosphorus removal kinetics were measured in detail. It was demonstrated that the removal process of phosphorus through BOF-slag followed pseudo-first-order reaction kinetics. The apparent rate constant(kobs) significantly decreased with increasing initial phosphorus concentration, BOF-slag size, and initial p H, whereas it exhibited an opposite trend with increasing reaction temperature and BOF-slag dosage.A linear dependence of kobson total removed phosphorus(TRP) was established with kobs=(3.51 ± 0.11) × 10- 4× TRP. Finally, it was suggested that the Langmuir–Rideal(L–R)or Langmuir–Hinshelwood(L–H) mechanism may be used to describe the removal process of phosphorus using BOF-slag.     

木质生物燃料与其半焦的混燃实验研究

生物质半焦作为生物质气化的副产物,其固定碳含量和热值均高于原生物质.若将生物质半焦充分利用将大幅提高生物质利用的能量效率,具有很大的经济和环境效益.在综合热分析基础上,考察了生物质半焦添加比例(掺烧比)对生物质微米燃料旋风炉燃烧炉膛温度、烟气及灰分的影响.试验研究发现掺烧比为20%(空气当量比为1.2,粉体粒径在0.177 mm以下,生物质含水率控制在8.1%以下),燃烧效果最好,燃烧效率高达98%,燃烧烟气中有害气体NOx和SO2的含量较少.     

Estimation and characterization of PCDD/Fs and dioxin-like PCBs from Chinese iron foundries

The iron foundry industry is considered to be a potential source of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). This study investigated the emission factors and total emission amounts of PCDD/Fs and dioxin-like polychlorinated biphenyls (DL-PCBs) from iron foundries in China. The concentrations and the World Health Organization toxicity equivalents (WHO-TEQs) are presented and the congener profiles are discussed in this paper.In the present work, 26 fly ash samples were collected and tested to quantify the PCDD/Fs and DL-PCBs generated by 14 plants of different scales, and five stack gas samples were collected from two (named as EFG and LFG) of those plants. The emission levels of PCDD/Fs and DL-PCBs indicated that hot-air cupolas had lower emissions than cold-air cupolas. When iron ore lump and sinter were used as raw material, the emission factors were about 250 ng TEQ t⁻¹ of product. However, if the raw material was scrap, the emission factors varied owing to the different contents of organic materials in the raw materials. It was found that the mean WHO-TEQ values of PCDD/Fs and DL-PCBs were 144 and 34.2 pg Nm⁻³ in stack gas and 20.0 and 1.58 pg g⁻¹ in fly ash. In multiple tests, it was estimated that the mean emission factors of PCDD/Fs and DL-PCBs were 365 and 10.9 ng WHO-TEQ t⁻¹ released to residue and 2719 and 555 ng TEQ t⁻¹ released to air. The total emission amounts of PCDD/Fs and DL-PCBs from Chinese iron foundries with cupola furnaces released to residue and air were 16.8 and 146 g WHO-TEQ in 2008, respectively.     

冶金炉重大危险源辨识及其爆炸事故后果模拟

冶金炉的铁水、钢水温度高,国内外多次发生冶金炉爆炸事故,但现阶段根据《重大危险源辨识》(GB18218-2000)和《关于开展重大危险源监督管理工作的指导意见》(安监管协调字[2004]56号文)还无法判定其是否为重大危险源.运用爆炸学、热学等方法,提出了判定冶金炉是否为重大危险源的理论与方法,并给出了判定高炉是否为重大危险源的临界有效容积,判定转炉、混铁炉是否为重大危险源的临界公称吨位,最后通过VB编程对冶金炉进行了爆炸事故后果模拟,为冶金企业提供一定的参考价值.     

熔融还原炼铁工艺环保可行性初步研究——以广州珠江钢铁为例

熔融还原炼铁技术是目前国内外高度重视的新一代炼铁技术,Corex和Hlsmelt是其中的代表工艺。文章就炼铁工艺在技术、环境、经济等方面有不同的要求而提出可行性判别指标,对Corex、HIsmelt与传统高炉工艺进行各判别指标的对比分析,并结合广州珠江钢铁有限责任公司现址建设炼铁项目这一实例从定性和定量的角度判别三种工艺的优劣,从而指出,对于珠钢现址,Corex和H／smelt比高炉技术更适应环保要求,更利于珠钢的未来发展,其中HIsmelt最具优势和竞争力。