高压衰减器的时域校准方法

本文介绍了一种基于系统辨识的高压衰减器的时域校准方法。依据系统辨识的基本原理,对高压衰减器建立输入、输出误差模型,通过测量衰减前后的时域波形,计算获得衰减器的传递函数,进而获得其修正系数。该方法可同时得到高压衰减器的幅频及相频特性,并可在高压校准条件下,准确反映衰减器的高压特性,为高压衰减器的时域校准提供了技术依据。     

Risk-Based Prioritization of Air Pollution Monitoring Using Fuzzy Synthetic Evaluation Technique

Air pollution monitoring programs aim to monitor pollutants and their probable adverse effects at various locations over concerned area. Either sensitivity of receptors/location or concentration of pollutants is used for prioritizing the monitoring locations. The exposure-based approach prioritizes the monitoring locations based on population density and/or location sensitivity. The hazard-based approach prioritizes the monitoring locations using intensity (concentrations) of air pollutants at various locations. Exposure and hazard-based approaches focus on frequency (probability of occurrence) and potential hazard (consequence of damage), respectively. Adverse effects should be measured only if receptors are exposed to these air pollutants. The existing methods of monitoring location prioritization do not consider both factors (hazard and exposure) at a time. Towards this, a risk-based approach has been proposed which combines both factors: exposure frequency (probability of occurrence/exposure) and potential hazard (consequence).This paper discusses the use of fuzzy synthetic evaluation technique in risk computation and prioritization of air pollution monitoring locations. To demonstrate the application, common air pollutants like CO, NO_x, PM₁₀ and SO_x are used as hazard parameters. Fuzzy evaluation matrices for hazard parameters are established for different locations in the area. Similarly, fuzzy evaluation matrices for exposure parameters: population density, location and population sensitivity are also developed. Subsequently, fuzzy risk is determined at these locations using fuzzy compositional rules. Finally, these locations are prioritized based on defuzzified risk (crisp value of risk, defined as risk score) and the five most important monitoring locations are identified (out of 35 potential locations). These locations differ from the existing monitoring locations.     

Optimization-Based Atmospheric Plume Source Identification

This work applies optimization and an Eulerian inversion approach presented by Bagtzoglou and Baun in 2005 in order to reconstruct contaminant plume time histories and to identify the likely source of atmospheric contamination using data from a real test site for the first time. Present-day distribution of an atmospheric contaminant plume as well as data points reflecting the plume history allow the reconstruction and provide the plume velocity, distribution, and probable source. The method was tested to a hypothetical case and with data from the Forest Atmosphere Transfer and Storage (FACTS) experiment in the Duke experimental forest site. In the scenarios presented herein, as well as in numerous cases tested for verification purposes, the model conserved mass, successfully located the peak of the plume, and managed to capture the motion of the plume well but underestimated the contaminant peak.     

假单胞菌好氧降解四溴双酚A的特性

为了解四溴双酚A(TBBPA)的好氧降解特性,采用选择富集法从活性污泥中分离出一株能够高效降解四溴双酚A的菌株。根据其形态、生理生化特性及16S rDNA核苷酸序列分析,该菌株被鉴定为假单胞菌属(Pseudomonas sp.)。研究结果表明,该菌株可通过好氧共代谢方式实现四溴双酚A的降解,葡萄糖是四溴双酚A降解的最佳碳源,其最优降解条件为葡萄糖8 g/L,牛肉膏0.5 g/L,pH值为7.0,培养温度为35℃,摇床转速为150 r/min。在该条件下其生物降解过程符合一级动力学模型,6 d后的降解率高达95.6%。LC-MS结果表明,四溴双酚A在好氧降解过程中会生成异丙苯酚类物质。     

抗铬菌株的筛选鉴定及其生物学特性和吸附特性

利用微生物分离纯化技术,在培养基中加入不同浓度的Cr3+、Cr6+,经过长时间驯化,从污染土壤中筛选出2株对Cr具有较高抗性的菌株(A和B),对其进行了形态、生理生化特性及分子生物学鉴定,并研究了其最佳生长条件及对Cr3+的生物吸附规律。结果表明,菌株A和B分别为蜡状芽孢杆菌(Bacillus cereus)和米根霉菌(Rhizopus oryzae)。菌株A和B的最适生长pH值均为7,最适生长温度均为30℃,最佳装液量为80~100 mL(250 mL摇瓶)。在培养时间一定时,随着Cr3+浓度的增加,菌株对Cr3+的吸附率减少,而生物吸附量则逐渐增大;在Cr3+浓度一定时,随着培养时间的延长,菌体对Cr3+的吸附率呈现出先增加后减少的趋势,这与生物吸附量的变化趋势基本一致。在Cr3+浓度为100 mg/L时,菌株A和B对Cr3+的吸附率达到最大,分别为51.47%和46.36%。     

SWMM 模型在城市不透水区地表径流模拟中的参数识别与验证

为了研究城市不透水下垫面的降雨径流过程和污染负荷,以屋面为例,选择径流管理模型SWMM,采用独立场次实测数据,应用基于不确定性分析的HSY算法和Monte Carlo采样方法对模型中的水文水力和水质参数进行识别和验证.结果表明,地表不透水区径流模型中主要包含6个关键参数,分别为不透水区初损填洼深度(S-imperv)、不透水区曼宁系数(N-imperv),指数累积方程中的最大可能累积值(max buildup)、累积常数(rate constant),指数冲刷方程中的冲刷系数(coefficient)和冲刷指数 (exponent).水文水力参数的识别可以最小二乘法偏差作为目标函数,水质参数的识别可以场次污染负荷和污染物峰值浓度作为目标函数.参数识别结果为N-imperv0.012～0.025, S-imperv 0～0.7, max buildup 15～30, rate constant0.2～0.8, coefficient0.01～ 0.05, exponent1.0～1.2.参数的区域灵敏度由大到小排序为 coefficient、S-imperv、N-imperv、max buildup、exponent、rate constant.识别后的参数可以通过模型验证,但是在模拟一些雨型特殊的降雨径流污染物浓度曲线时,仍然存在一定的困难.     

An integrated assessment method of urban drainage system:A case study in Shenzhen City,China

In recent years, the urban drainage system in China is facing the dual pressure of renovation and construction. This requires that the integrated assessment for the planning and operation of the urban drainage system is obligatory. To evaluate the urban drainage system, an integrated assessment methodology based on the analytic hierarchy process (AHP), integrated simulation, and fuzzy assessment is established. This method is a multi-criteria decision adding app roach to the assessment of the urban drainage system comprehensively. Through the integration of the Storm Water Management Model (SWMM), a simple wastewater treatment plant model, and a surface water quality model, an integrated modelling system for the urban drainage system is developed and applied as a key tool for assessment. Using the established method, a case study in Shenzhen City has been implemented to evaluate and compare two urban drainage system reno vation plans, the distributed plan and the centralized plan. Because of the particularity of this case study, the established method is not applied entirely. Considering the water environ mental impact, ecological impact, technological feasibility, and economic cost, the integrated performance of the distri buted plan is better. As shown in this case study, the proposed method is found to be both effective and practical.     

Design of policy mechanism to promote cleaner production in China

ＩｎｔｒｏｄｕｃｔｉｏｎＣｌｅａｎｅｒｐｒｏｄｕｃｔｉｏｎ (ＣＰ)ｈｏｌｄｓｇｒｅａｔｐｒｏｍｉｓｅａｓａｎｅｆｆｅｃｔｉｖｅｓｔｒａｔｅｇｙｉｎｔｈｅｆａｃｅｏｆｄｏｕｂｌｅｃｈａｌｌｅｎｇｅｓｏｆｅｎｖｉｒｏｎｍｅｎｔａｌｐｒｏｔｅｃｔｉｏｎａｎｄｅｃｏｎｏｍｉｃｄｅｖｅｌｏｐｍｅｎｔ.Ｉｎ 1993,ａｄｅｍｏｎｓｔｒａｔｉｏｎｐｒｏｊｅｃｔ (Ｂ 4ｐｒｏｊｅｃｔ) ,ｄｅｓｉｇｎｅｄａｎｄｅｘｅｃｕｔｅｄｂｙｔｈｅＳｔａｔｅＥｎｖｉｒｏｎｍｅｎｔａｌＰｒｏｔｅｃｔｉｏｎＡｄｍｉｎｉｓｔｒａｔｉｏｎ (…     

溢油多环芳烃模糊指数的研究

通过用氧化铝柱层析和等梯度呷醇：水=85％：15％）反相高效液相色谱（C18硅烷柱）紫外检测器254nm,测定30多种油品和我国海洋环境油类样品中的多环芳烃（PAHs）,建立了溢油PAHs模糊指数结果表明,油类PAHs响应因子和相对保留值的变异系数分别在8.4％－16.5％和0.00％－5.4％之间,回收率在74.6％－111.2％之间,精密度和准确度较好;海洋环境油类的多环芳烃模糊指数值（0.00383－0.01839）与润滑油类的值（0.00106－0.00942）接近,较石油及其它产品油的值（0.06983－1.00000）低;用润滑油类作为标准油,PAHs模糊指数作为溢油芳烃类监测的指示物（指标）,可提高监测海洋环境油类的代表性和可靠性     

分光光度法快速测定化学耗氧量

本方法是重铬酸钾法改进与仪器自动测定法相结合的一种快速分析方法，氧化消耗量是重铬酸钾法的十分之一，测定时间仅４０分钟，操作简便，适合于工厂污水处理场中间控制分析要求。