生活垃圾高温空气气化处理的低污染特性分析

本文介绍了高温空气气化城市生活垃圾的工作原理及过程 ,分析了城市生活垃圾高温气化反应机理。通过对高温空气 /蒸汽发生器、高温气化炉及湿式除尘器等关键部件的分析发现 ,采用高温空气气化系统可实现城市生活垃圾低污染处理     

生物质气化过程催化剂应用研究进展

生物质气化技术已在国内外得到广泛的开发和运用,但由于燃气品位较差,焦油较多,限制了生物质气化气的进一步利用。在生物质气化过程中应用催化剂是一种有效的提升燃气质量和催化裂解焦油的方法,近年来已引起了国内外的广泛注意。本文对国内外生物质催化气化及相关研究进展进行了综合评述,分析了催化剂对减少生物质气化焦油的生成和改进燃料气品质的作用结果, 提出了进一步的研究方向。     

城市生活垃圾催化气化制取富氢气体的研究

采用下吸式固定床气化炉,以煅烧白云石为催化剂水蒸气气化城市生活垃圾(MSW)有机组分,在气化温度为750~950℃,S/M(水蒸气和垃圾物料进料质量比)为0.57~1.28时,探讨了催化剂种类、气化温度和S/M等因素对富氢气体成分、产氢率、潜在产氢率、低位热值和碳转化率等的影响。较高气化温度有利于富氢气体的生成,增加碳转化率和产气率,但会降低富氢气体的热值;在实验条件下,富氢气体中H2体积分数最高达53.29%,产氢率达到7.13~46.52mol/kg,潜在产氢率为55.48~90.11mol/kg;镍基催化剂催化效果优于煅烧白云石,能大幅增加H2含量,使焦油在850℃以上完全分解。     

Explosion parameters of wood chip-derived syngas in air

The wood gasification process poses serious concerns about the risk of explosion. The design of prevention and mitigation measures requires the knowledge of safety parameters, such as the maximum explosion pressure, the maximum rate of pressure rise and the gas deflagration index, K_G, at standard ambient temperature (25 °C) and pressure (1 bar) conditions. However, the analysis at specific process conditions is strongly recommended, as the explosion behavior of gas mixtures may be completely different.In the work presented in this paper, the explosion behavior of mixtures with composition representative of wood chip-derived syngas (CO/H₂/CH₄/CO₂/N₂ mixtures with and without H₂O) was experimentally studied in a closed combustion chamber. Experiments were run at two temperatures, 300 °C and 10 °C, and at atmospheric pressure. Test conditions were requested by the safety engineering designer of an existing industrial-scale wood gasification plant. In order to identify the specific fuel–air ratios to be analyzed, thus reducing the number of experimental tests, a preliminary thermo-kinetic study was performed.Results have shown that the mixtures investigated can be classified as low-reactivity mixtures, the higher value of K_G found (∼36 bar m/s) being much lower than the K_G value of methane (55 bar m/s @ 25 °C).     

煤气化装置泄漏爆炸事故伤害作用区域研究

利用FARO-Phonton三维激光扫描设备结合Microstation软件对某煤气化装置进行精确建模,根据厂区的实际情况设定可能的爆炸事故场景,运用计算流体力学软件FLACS研究不同爆炸事故对周边环境的作用过程及伤害区域,并与传统蒸气云爆炸伤害作用区域计算方法进行了比较分析.对比研究结果显示,基于FLACS的技术方法能综合考虑复杂装置设备对爆炸后果的影响,预测爆炸后空间各个部位超压的变化趋势及规律,能够弥补传统经验公式法的不足,更加适用于煤气化装置爆炸事故状态下应急救援区域的划分与确定.     

Waste gasification vs. conventional Waste-to-Energy: a comparative evaluation of two commercial technologies

A number of waste gasification technologies are currently proposed as an alternative to conventional Waste-to-Energy (WtE) plants. Assessing their potential is made difficult by the scarce operating experience and the fragmentary data available. After defining a conceptual framework to classify and assess waste gasification technologies, this paper compares two of the proposed technologies with conventional WtE plants. Performances are evaluated by proprietary software developed at Politecnico di Milano and compared on the basis of a coherent set of assumptions. Since the two gasification technologies are configured as “two-step oxidation” processes, their energy performances are very similar to those of conventional plants. The potential benefits that may justify their adoption relate to material recovery and operation/emission control: recovery of metals in non-oxidized form; collection of ashes in inert, vitrified form; combustion control; lower generation of some pollutants.     

生物质气化多发事故及防范

近几年，秸秆气化供气发生事故较多，对事故易发原因进行了归纳与分析，并提出了防洪措施。     

壳牌煤气化技术的应用前景分析

介绍了壳牌煤气化技术的工艺特点和发展现状,分析论述了分布式能源系统技术,将煤气化与分布式能源系统两种技术完美结合,是当今煤-电-化组合的优良模式.     

回转窑热解气化炉处理生活垃圾特性

基于目前固定床热解气化法在常温下进行存在燃气热值和气化效率较低、燃料适用范围小和预处理复杂等问题,采用控制变量法设计探究了不同预热空气温度和过量空气系数对小型回转窑式热解气化炉处理村镇生活垃圾的影响.结果表明:预热空气温度升高有利于垃圾热解气化产气,但有一定的局限性,当温度超过600 ℃时垃圾的气化产气明显下降;当过量空气系数为0.4时,垃圾的热解气化效率达到最大值,并且焦油产量最小.垃圾原样在过量空气系数为0.4、空气预热温度为500 ℃下对底渣、飞灰进行重金属含量的分析测试结果显示,飞灰中的铅含量远高于GB 18598—2001《危险废物填埋污染控制标准》相关标准限值,需要经过处理才能排放,二英采样分析结果显示其含量均低于GB 18485—2014《生活垃圾焚烧污染控制标准》限值.研究显示,该回转窑式热解气化工艺处理生活垃圾的最佳过量空气系数为0.4,最佳空气预热温度为500 ℃,在此最佳工况条件下焦油产量小,飞灰及焦渣中重金属含量小,ρ(二英)低于0.10 ng/m3.      

Heavy metals fraction and ecological risk evaluation in municipal solid waste gasification slag non-burnt bricks

The heavy metals in non-burnt bricks made from municipal solid waste (MSW) gasification slags with a modified European Bureau Community of Reference procedure were studied. Heavy metals were present in the form of oxidizable and residual fractions, which were stable and not easy to dissolve. The preparation process of non-burnt bricks displayed prominent solidification effect for some heavy metals in the gasification slag. The solidified rate for metals, such as As, Cd, Cr, Ni, and Zn reached 89.82%, 79.57%, 73.64%, 66.73%, and 88.05%, respectively. Moreover, the leaching concentrations of eight heavy metals were all below 8 mg/kg. On the basis of these observations, the risk of exposure to heavy metals in non-burnt bricks was evaluated using the solidification formula and the leaching concentration of heavy metals combined with the assessments of the Hakanson potential ecological risk and pollution ratio of secondary phase and primary phase. Results showed that the preparation of MSW gasification slag non-burnt bricks was not harmful to the environment, but attention is warranted for possible migration of heavy metal cadmium (Cd) in the long term, which may result in an impact on the ecological environment.